American Standard 3011.016.021 Cadet-3 Round Front Toilet Bowl, Bone (Bowl Only)

How to repair a leaking toilet tank

The toilet tank contains the water before rinsing. After pressing the discharge handle, the water in the tank is exhausted to the bowl and the distance colors of the wastewater. Because it is constantly carrying water, the tank has a lot of opportunity to leak. A leaking tank should not have to call a plumber immediately, however. Repairing a leaking toilet tank is something that even the average diyer can do on its own.



American Standard 3011.016.021 Cadet-3 Round Front Toilet Bowl, Bone (Bowl Only)

Instructions

1 Turn off the water in the supply. This is under the tank on the side of the wall. Cut the water by turning the knob clockwise. This will help prevent new leaks.

2 Unload the toilet to get rid of all the water inside the tank. Collect the extra with rags and sponges.

3 Disengage the water supply from where it connects to the tank.

4 Remove the tank from the bowl. The heads of the screws are in the lower part of the tank. Hold a screwdriver on their head while unscrewing the nut from below with a wrench. In most models, two bolts are holding the tank to the cup.

5 Set a towel on the floor. Carefully lift the tank from the cup and put it upside down on the towel.

6 Remove the cone gasket at the bottom of the tank. This is the part that connects the tank to the cup. Check this for leaks. Even if it is in good condition, it is a good idea to change these each year more or less. Replace the cone seal or replace it with a new one.

7 Check the rubber gaskets on the bolts. As with the cone gasket, they can deteriorate over time. Replace those that are cracked or broken.

8 put the tank back in the cup. Make sure that the cone seal is correctly aligned with the hole in the container.

9 loosen the screws and rubber washers through the holes in the bottom of the tank and through the container. Tighten the nuts of the tightened hand, and then an additional turn with the key.

10 Wrap a strip of plumber's tape around the water inlet in the tank. This will help prevent the water supply from leaking. Squeeze the water hose in the inlet, the hand tightened at first, and then use a wrench.

11 Open the water supply and allow the bath to fill.

12 Pull the chain. Check for leaks around the tank.

Tips and warnings

•     Be careful not to over tighten the nuts around the toilet, as this could break the porcelain.
•     Do not try to repair a fissured toilet tank crack with putty. Replace the entire tank.

American Standard 3191.016.222 Colony FitRight Right Height Elongated Toilet Bowl, Linen (Bowl Only)

How to repair the chain in the toilet tank

If you press the handle of the toilet on the toilet and nothing happens, you have a problem with your toilet chain. The handle on the outside of the toilet tank is connected to a discharge rod that rises in response to the action of the handle. When this rod lifts, pulls a chain. Attached to the other end of the chain is the odorless fin. When the chain raises the fin, it allows the water inside the tank to escape and discharge. Repair of the chain in the toilet tank is a relatively simple operation.



American Standard 3191.016.222 Colony FitRight Right Height Elongated Toilet Bowl, Linen (Bowl Only)

Instructions

1 Close the water supply for the toilet that contains the chain you want to repair. The toilet supply valve is located on the wall behind the toilet. You should see a hose or tube that goes from the supply valve to the toilet tank. Turn the knob on the end of the water supply valve to the right to close the water.

2 Lift the lid of the toilet tank. Locate the toilet flap, which is the rubber stopper on the bottom of the tank. Normally, when the discharge lever is pressed, this raises the fin and allows the water to rotate out of the tank. This, however, will not be the case if the chain needs to be repaired. Reach your hand in the tank - do not worry, the water is treated - and grab the fin with your hand. Pull the tongue and allow the water inside the tank to escape.

3 Examine the chain and determine where the break occurs. A break in the middle of the chain can be repaired by reattaching the two halves of the chain back together with a piece of wire. If the break occurs, either in the discharge lever or the trap, replace these links as necessary, either with cable or by adding a replacement link. You can buy chain replacement links that slide over the flap or the dipstick as a car key ring.

4 Press the discharge handle and check that the chain opens and closes the flap when operating. Press the flap down on the flap opening at the base of the tank.

5 Restore the water supply by turning the water supply knob clockwise. Let the tank fill up.

6 Pull the chain and see the flap and chain. Make sure it works properly with the full tank. Replace the tank lid.

Tips and warnings

•     Some of the hardware stores sell toilet chain repair kits that have many of the replacement parts you need.
•     If the chain breaks in the middle, this repair is a good temporary solution. However, the chain must be replaced as soon as possible.

STERLING 403215-47 Windham Elongated Toilet Bowl, Almond

How to repair a filling valve of a toilet tank

The filling valve, as the name implies, refills the toilet tank with water after a wash. These accessories are controlled by a set of valve float. As the water level in the tank rises, it leads up to the float valve, which finally cuts off the water supply to the fill valve when it reaches a predetermined level. The best way to repair a fill valve in a toilet tank is by replacing the entire filling valve assembly. They are not expensive and the work is not complicated, even for a plumber for the first time.



STERLING 403215-47 Windham Elongated Toilet Bowl, Almond

Instructions

1 Close the water for the toilet cistern. Follow the water supply valve from the bottom of the toilet bowl to its confluence with the supply valve on the wall. Turn the knob oval on the front of the valve to the right to close the water.

2 Remove the tank lid and set aside. Download the bathroom. Hold the handle down after pulling the chain and allow all the water inside to flow out. Wipe away any excess with the towel and sponge.

3 To remove the valve float from the filling valve. In most cases, the valve float can be separated by removing the two wing nuts that hold it. This step is not necessary in a filling valve with an integrated float.

4 Place a towel on the floor under the tank. Unscrew the water supply hose from the inlet on the bottom of the tank with a pair of pliers. Loosen the plastic retaining nut on the inlet. Lift the old fill valve up and out of the tank.

5 Clean the area immediately around the filling valve base at the base of the tank. Use a spatula to scrape and remove any buildup of sediment or calcium. Apply a light coat of silicone grease on the perimeter of the socket.

6 Insert the new filler valve into the filler valve socket. Make sure the gasket is tight on the bottom. Keep this with one hand. With the other hand, take the retaining nut and place it under the toilet cistern. Screw the retaining nut onto the threads on the bottom of the filling valve. Tighten with the key.

7 Replace the float assembly, if present.

8 Wrap the inlet threads of the fill valve in the bottom of the tank with plumber's tape. Fix the water supply hose and tighten with the pliers. Reset the water supply by turning the water supply button counterclockwise. Allow the bathroom to fill up

9 Pull the chain and check that the new filling valve is working correctly.

Tips and warnings

•     Do not over tighten any of the retaining nuts or plastic couplings, as this could cause the plastic to crack.

Toto CT708EGNo.01 Commercial Flushometer High Efficiency Toilet-1.28-GPF, Top Inlet Spud, Cotton

How to install a filling valve for a toilet tank

With all the mechanical action that takes place in a toilet tank, it is not surprising that some of the internal parts will need replacement from time to time. If the toilet tank still works or did not work properly, it is time to replace the fill valve. It is not a difficult task, even if you do not have any plumbing experience.



Toto CT708EGNo.01 Commercial Flushometer High Efficiency Toilet-1.28-GPF, Top Inlet Spud, Cotton

Instructions

1 Cut off the water supply for the toilet and pull the chain to remove the water. It is also possible that at this time you want to clean all the lines and valves involved.

2 Remove the lid of the toilet tank. Using the sponge, remove more water still standing in the tank.

3 Loosen and remove the feed line from the bottom of the tank. Have your bucket ready to pick up the water that is standing in the old pipe or valve.

4 Remove the large retaining nut just above the power line at the bottom of the old unit, and remove the unit from the tank.

5 Clean the tank clean and dry, with the sponge before installing the new unit to remove any particles of grain or rust that could ruin the new seal or valve.

6 Set the new fill valve. Most new valves twist to adjust the height. You want to adjust to the highest point you can go without touching anything inside the tank. Now you just have to reinstall the new unit in the place of the old one. Make sure the float does not touch the sides or top of the tank or the ball valve on the bottom.

7 Install the overflow tube in the overflow tube. These usually only latch on top.

8 Install and tighten the unit retaining nut. Just tighten this nut enough to hold it - be careful not to break the porcelain. Wrap the threads on the end of the feed line of the Teflon tape unit and install the feed pipe and tighten. Do not over tighten this accessory as it is a plastic connection in most cases and can easily break.

9 Open the water again and pull the chain. If you do not discharge or refill correctly, you may have to adjust the height of the new fill valve by turning it higher or lower.

Tips and warnings

•     Great idea if you have more than one rental property, it will save you a few dollars in time.
•     Old plumbing tends to have sharp rusty edges sometimes. Be careful how to handle these elements.

TOTO C743E#01 Drake Round Front Bowl, Cotton White

How to replace the float valve in a toilet tank

When a hygienic float valve goes bad, that means that the tank can no longer hold water between discharges. As a result, the toilet is running constantly, which wastes a large amount of water and can lead to utility bills. Replacing the float valve is a simple home repair that requires only a few instruments and about a half hour of maintenance staff time.



TOTO C743E#01 Drake Round Front Bowl, Cotton White

Instructions

1 Turn off the water supply to the toilet bowl by turning the valve handle located behind the toilet. Lift the lid of the toilet tank and keep it in reserve. Pull the chain so that all the water runs out of the tank. Use a sponge to absorb any excess water left in the tank.

2 Place a towel on the floor at the base of the back of the toilet. The towel will absorb water that leaks from the toilet during the process.

3 Use a pair of pliers to disconnect the pipe from the wall to the toilet tank. Disconnect the hose at the end of the tank by loosening the plastic nut that connects the hose to the tank.

4 Switch to a spanner. Use the wrench to loosen the nut that holds the float valve in place. The nut is located near the area that the hose is fed into the tank.

5 Release the thin plastic tube inside the valve tank and lift the valve from the toilet tank. Discard the old valve.

6 Read the instructions that accompany the new float valve. Install the rubber grommets firmly into the hole of the float valve on the base of the tank. Insert the new float valve into the hole and carefully tighten the retaining nut on the bottom of the tank.

7 Reconnect the hose to the valve and connect the thin plastic hose inside the toilet tank to the valve. Make sure all stamps are in place. Open the water supply and see if there are leaks around the tube. Tighten the seals and the plastic nut, if necessary.

8 Look inside the tank, as it fills with water. If the valve is installed correctly, there should be no leaks and the water line should be about a half inch from the top of the tank.

KOHLER K-4304-L-0 Highline(R) Toilet with Pressure Lite(R) Flushing Technology and Bedpan Lugs, White White

How to replace a toilet ball valve

Combined with a float ball that rises and falls with the water level, the ball valve directs the flow of water into a toilet water tank. The ball valve in the water inlet tube opens when the ball float is lower than the desired water level and closes tightly, preventing water from flowing into the tank when the ball reaches the top of the line of water. If the toilet has a ball valve and runs non-stop, that could be the float or ball valve. Both are easy to fix and can be replaced in a couple of hours.



KOHLER K-4304-L-0 Highline(R) Toilet with Pressure Lite(R) Flushing Technology and Bedpan Lugs, White White

Instructions

1 Close the water in the shut-off valve. Look for it connected to the water pipe behind and just to the left of the back of the toilet. If there is no valve in the toilet, or if you can not tighten with your fingers, turn off the water supply to the house until repairs are complete.

2 Pull the chain to ensure that the water is completely free. Water should not come out again in the reserve tank once emptied. If the water does not continue to flow into the tank, you should use a shut-off valve all the water in the house instead of the toilet water trigger to remove and put the shut-off valve on your list of things to replace in the future.

3 Remove the water line from the bottom of the toilet with a wrench or adjustable pliers. Remove the lid of the toilet tank by lifting it and set it aside.

4 Disconnect the nuts securing the ball valve and the water supply pipe to the tank using pliers. Check all the inner washers of the valves for cracking, tearing or other reasons to replace them.

5 Place the new ball valve with the existing or new washers, and place it through the bottom of the reservoir. Wrap the valve threads with the plumber's tape and attach it to the water pipe.

6 Replace and tighten all nuts to secure the ball valve and water line in place. Secure the ball float arm of the valve.

7 Open the water supply, either in the water shut-off valve behind the toilet, or in the water shut-off valve for the entire house. Check the water level to make sure the tank is filled properly. Adjust the float if the water levels are too high or too low. Put the lid on the tank.

Toto CST794EFRNo.01 Elongated Bowl and Tank with Right Hand Trip Lever 1.28-GPF, Nexus Collection, Cotton

How to replace a toilet and float valve

The float valve, also known as the valve or fill valve, is the accessory that fills your toilet after a flush. After the water leaves the tank, the float valve, normally in place by the water in the tank, decreases, allowing water to flow to it. When the float valve reaches a set height, the water flow to the fill valve is cut off. The replacement of a toilet or float valve involves draining the toilet so that it can reach the valve, remove it and replace it with a new one.



Toto CST794EFRNo.01 Elongated Bowl and Tank with Right Hand Trip Lever 1.28-GPF, Nexus Collection, Cotton

Instructions

1 Close the water for the toilet in which you will replace the toilet valve and float valve. This is usually behind the toilet on the wall. The supply shutoff valve will be round or oval. Turn this clockwise to close the water supply.

2 Pull the chain. Hold the handle down until all the water supply is gone. Wipe away any excess with a towel and sponge.

3 Disconnect the float valve lever from the fill valve. This could be held in place with a screw or snapped into place, depending on the model.

4 Disconnect the water supply valve from the inlet of the filling valve by unscrewing it. Unscrew the plastic retaining screw above the filling valve inlet. This keeps the fill valve in place in the bottom of the tank. Lift the fill valve and out of the tank.

5 Turn the new fill valve upside down. Apply a thin layer of grease to the bottom of the filler valve gasket. Turn the filling valve right side up. Insert into the tank so that the seal is flush with the bottom of the tank. Keep holding this in one place with your hand.

6 Reattach the retaining screw to the bottom of the tank by screwing it around the tank inlet. Tighten with the key.

7 Replace the float valve.

8 Wrap the inlet threads with plumber's tape. Replace the water inlet coupling.

9 Reset the water supply. Let the tank fill up. Rinse and check correct operation.

Tips and warnings

•     If possible, try replacing the fill valve that comes with an integrated float valve.

American Standard 3121.016.178 Champion Elongated Seatless Toilet Bowl, Black (Bowl Only)

How to repair a Cup float valve in a toilet

A float valve is a common type of toilets.The valve discharge valve consists of a tower in which a round plastic cup moves up and down. When the chain is pulled, the drop in the water level causes the cup to drop, letting the water flow into the tank. When the cup rises to the top, it will turn off the water. The main problem with the valves of the float cup is that the cup sticks, causing the water to run constantly. The repair of the float valve requires ensuring that the float cup moves smoothly in the tower.



American Standard 3121.016.178 Champion Elongated Seatless Toilet Bowl, Black (Bowl Only)

Instructions

1 Remove the lid of the toilet tank and put it out of the way.

2 Turn the shutoff valve on the floor next to the toilet all the way to the right to stop the water supply to the toilet. Pull the chain to remove most of the water in the tank.

3 Search for the float valve, which is on the left side of the toilet. Notice how the plastic cup is attached to the tower.

4 Apply plumber's grease with a cotton swab to the tower and the inside of the cup where the tower is inserted into it. Move the cup up and down the tower to work on the fat.

5 Turn on the shut-off valve for the water supply to the tank. Pull the chain several times to make sure the cup is working properly. Replace the tank lid.

STERLING 403315-0 Windham Toilet Bowl, White

How to adjust the float valve in a toilet

The float valve controls the water level in the toilet tank. As the water fills the reservoir, the float rises. When the float reaches a predetermined level, the water supply is interrupted. When your toilet is constantly running or you do not pull it completely, you need to adjust the float valve. The adjustment depends on whether you have a ball float or a float that rests on the fill valve.



STERLING 403315-0 Windham Toilet Bowl, White

Instructions

floating ball

1 Remove the tank lid from the toilet and place it on the ground out of your way. Locate the brass adjustment screw below the end of the ball float arm on top of the fill valve.

2 Turn the screw counterclockwise with a Phillips screwdriver to raise the water level if the bath is not emptying completely. Turn the 1/2-turn screw at the same time. Turn the screw clockwise with the screwdriver to lower the level if the toilet is running constantly.

3 Pull the chain and allow the toilet tank to fill. The water should be in the filling line on the back of the toilet cistern. They continue to make adjustments to the screw ball float as needed.

4 Place the toilet tank lid on the toilet once you have completed the adjustments.
Float-on-Fill valve

5 Take the lid of the toilet tank out of the toilet and place it on the floor out of your way.

6 Locate the level adjustment clip next to the float. The clip is a clip fastener that moves up and down a thin wire.

7 Squeeze the top and bottom of the clamp with your fingers. Lift the clip fastener and float to lower the water level, or lower them to increase the water level. Move the float and clip fastener in 1/2 inch increments.

8 Pull the chain and let the tank refill. There is a water line on the back of the toilet cistern. Continue making adjustments as necessary until the water level is in the water line on the back of the toilet tank.

9 Place the toilet tank lid on the toilet after all the settings are complete.

Tips and warnings

•     Do not bend the ball float arm to make adjustments. Bending the ball float arm could damage the connection at the top of the fill valve.

Duravit 22170900921 Toilet Bowl Wall-Mounted 14 5/8-Inch Vero

Problems with flush toilet valves

Bathrooms are a modern convenience when they are working properly, but they are a modern nuisance when they are not. A dump valve is a relatively simple mechanism, but when it starts to malfunction, it is difficult to repair, especially since many homeowners never look toward the back of their toilet until something goes wrong and they really do not know how the water works. toilet.



Duravit 22170900921 Toilet Bowl Wall-Mounted 14 5/8-Inch Vero

Partial closure

If the discharge valve closes only to a certain point, your toilet will probably continue to run and waste of water. Check that nothing is blocking the discharge valve and keep it open and that the toilet tank cover is not obstructing the movement of the discharge valve.

damaged joint

A damaged gasket or crack or hole in the tank below the discharge valve will lead to the same symptoms as a discharge valve that will not close: you will hear running water in the toilet when it should not. Inspect the discharge valve and the area around it for damage or something unusual, which could include cracking or discoloration of the porcelain, interference or obstruction by foreign objects or broken or bent mechanisms.

Bent ball tank

Tank balls were replaced with fins many years ago, but, if you have an old toilet, you can still have a tank ball, which is a plastic or metal sphere attached to a rod. The tank ball floats on the surface of the water in the toilet tank and lifts a lever that closes the discharge valve when the tank is full. If the rod to which the tank ball is attached is bent so that the tank ball is too low, the water stops before the tank is full. If the tank ball is too high, the water keeps running in the overflow tube because the mechanism has not told it to stop.

Flooded Fin

If you have a new toilet, your toilet has a flap valve instead of a tank ball. If you are having problems with the discharge valve, the fault lies most likely to be the trap. If the flap valve becomes saturated with water, it may fail to seal the outlet pipe and the water will continue to run outside the pipe, preventing it from shutting down. Replacing the flooded fin with a new one will solve this problem.

SANIFLO SANIACCESS 3 UPFLUSH MACERATOR PUMP + ROUND TOILET KIT, WHITE FINISH

How to troubleshoot a toilet that does not discharge

Toilets usually work without much maintenance, so a toilet that does not go flush could cause some concern for a homeowner. It is a simple plumbing fixture. The reservoir on the back of the toilet bowl contains water that removes debris. A handle on the front of the tank raises the arm inside the tank. The arm pulls a plunger that holds the water inside the tank. When the plunger is lifted, the water runs in the toilet bowl. If any of these components breaks, the toilet does not discharge.



SANIFLO SANIACCESS 3 UPFLUSH MACERATOR PUMP + ROUND TOILET KIT, WHITE FINISH

Instructions

1 Lift the lid of the toilet tank and set it aside.

2 Inspect the handle and make sure that the handle arm is still attached to the handle. Push the handle down to see the arm of the handle in action. It should be lifted up and down.

3 Place the chain that goes to the fin on the bottom of the tank if it has fallen. Make sure there is enough slack in the fin chain to close, but it is short enough that the fin lifts when the handle is rotated.

4 Check the trap and make sure it is connected to the discharge valve and that it moves freely.

KOHLER K-4197-96 Wellworth Round-Front Bowl, Biscuit

What to do with a toilet that overflows

A flooded toilet presents an immediate problem that must be resolved before the toilet can be used again. First you will have to stop the toilet from overflowing, and deal with the blockage in the drain pipe of the toilet bowl to prevent it from overflowing again. Avoid clogging your toilet by using less toilet paper and not putting other objects in the toilet.



KOHLER K-4197-96 Wellworth Round-Front Bowl, Biscuit

Close the tap

First you will have to stop the toilet from overflowing by cutting off the toilet's water supply. You will have to locate the closing valve of the toilet, which is usually located near the floor behind or next to the toilet. Once you find the valve, turn the lever to the right as far as your hand can use it. Do not use a wrench or other tool to tighten the handle, or you could damage the handle or valve. If the water continues to flow, you will have to close the main water valve in the house, which will turn off all the water in the house, until the toilet can be repaired. Clean the water on the floor since it left that can lead to water damage or mold growth.

Use a plunger

Find a funnel cup plunger to use in the toilet, as it has a curved extension in the bottom of the cup that creates more pressure in the toilet's drain pipe. Regular plungers that have a simple cup of them work best in sinks and tubs when they clog. It is necessary to place the plunger cup in the toilet and cover the drainage hole, creating an airtight seal between the container and the edges of the plunger cup. Vigorously pump the handle of the plunger up and down at least a dozen times, remove the cup from the drain hole and pull the chain to see if the clogging persists. Continue sinking if you see the progress; otherwise go to the auger.

Use an endless screw

A closet auger consists of a handle and a long, flexible hose that has a metal hook or corkscrew on one end. You feed the flexible part of the auger in the toilet drain opening, hook or at the end of the corkscrew first, ensure that you do not scratch the porcelain. Turn the handle to the right of the auger to feed more deeply into the toilet drain pipe and to push through any blockage in the pipe. Once you reach the end of the flexible hose, retract the drain screw by turning the handle to the left. Depending on the severity of the obstruction is, you may have to feed the auger in the toilet up to three times. The first time it is needed to point towards the center of the leak; in subsequent attempts feed the auger through the left and right walls of the leak in an effort to clean the entire drain pipe.

Call a plumber

Some toilet blockages will still not come free, even after using an endless screw. These clogs require the experience of a trained plumber, who will employ additional methods that are necessary to return his toilet to his normal work order. There may be a bigger problem in your home's plumbing if you notice water backing up in other drains in your home.

Kohler K-4067-NY Bancroft Comfort Height Elongated Bowl, Dune

Problems with the float valve in a toilet

Toilets are a useful modern convenience when they are functioning properly, but can be irritating when they have problems. Understanding how the toilet works will make it much easier to treat if and when problems develop. The problem with a toilet in constant operation or leaks is usually related to the float valve. Only old toilets have float valves; these have been replaced in the new toilets with discharge valves.



Kohler K-4067-NY Bancroft Comfort Height Elongated Bowl, Dune

Tilted arm float valve

If the toilet is running constantly, either, or stops before the bowl has been filled, the problem may be that the arm of your float valve is bent, causing the float valve to be at the wrong height. Remove the lid of the toilet tank from your rear and take a look. The plastic or metal ball that floats on the surface of the water is the float valve. When the water rises high enough, the ball is pushed upwards and a shut-off valve is activated. If the arm bends up, the water will reach high enough to start running the overflow before closing the valve. If the arm bends down, the valve will close before the bowl has finished filling.

Waterlog

Sometimes, the float valve can develop a crack or leak, causing it to fill with water. When this happens, it no longer floats on the surface of the water. When the chain is pulled, the rear tank will refill, but the ball will not float on the surface of the water, and the water will simply continue to run in the rear tank and exit through the overflow valve.

Break

If the arm of the float valve is bent or shaken too badly, the float valve may break out of it. If you take the lid of your rear tank and you see the float valve floating in the water, but not connected to anything, this is obviously what happened. You will probably need to replace both the float and the float arm to operate the toilet correctly.

Mansfield 135WHT 135010007 White Elong Toilet Bowl

Problem with a toilet that does not get enough pressure

If you accidentally press the handle on a toilet and, instead of listening to a color, are greeted by the sound of an empty tank, you are likely to have a water pressure problem on your hands. Since plumbing systems are made up of a number of different parts, there may be some reasons why you have a problem with a toilet not getting enough pressure.



Mansfield 135WHT 135010007 White Elong Toilet Bowl

Main water

If the toilet is not getting enough pressure, the first thing to check is the main water that reaches your home. This is the main line that all the water in your house is pumped through. In urban areas, this is generally maintained by the city or municipality, while in rural areas this can be managed by the county or it may have its own water supply. Turn on the other appliances or accessories in your home that use the water. If none of them has water, then this is the problem. Contact your city or city office to see who to speak or, if you have a private offer, a local plumber.

The plumbing pipes

Between the main water and the toilet are the plumbing pipes that carry water to the water supply valve. If one of these tubes blocked or begins to release, there will be no pressure in the toilet. Check the pressure in said ducts by opening the nearest faucet, since these are usually in the same feed tube as the toilet. If there is no pressure in the tap, the problem is in the plumbing pipes. These pipes, unfortunately, are usually buried inside wall spaces. In order to repair, remove the drywall (and any tile covering) to access the pipes.

Water supply valve

The water supply valve is located between the water supply pipe and the supply hose for the toilet. These accessories are usually made of metal and project about three or four inches from the wall behind the toilet cistern. If the water supply valve is clogged or damaged, it will not bring the water to the toilet cistern. To check, turn the handle on top of the supply tube by turning it all the way to the right. Disconnect the water supply hose for the toilet. Place a towel on the floor under the valve. Open the valve slowly. If the water comes out, then the valve is good. If not, replace the valve. Turn off the water supply before removing the old valve and replacing it with a new one.

Toilet filling valve

The last step in the water supply chain of a toilet is the filling valve. The filling valve is in the toilet tank. A supply hose connects the supply valve to the bottom of the fill valve. A malfunction of the filling or broken valve will not have enough pressure to fill the tank above. Filling valves are very expensive to buy and easy to replace; They are really not worth the trouble of trying to repair. Also, if it is a larger filling valve without anti-siphon technology, you may be in code violation if you try to repair an old one. To replace, close the water supply, unscrew the water supply hose, loosen the nut on the bottom of the fill valve and replace it with a new one.

KOHLER K-4325-L-0 Kingston(TM) Wall-Mounted 1.6 or 1.28 GPF Flushometer Valve Toilet Bowl with Top Inlet and Bedpan Lugs, Without Seat, White White

Problem with a toilet that emits a suction sound

Your toilet can make some noise each time you wash, otherwise a suction sound indicates a problem, either with a blockage in the drain pipe or an obstruction or damage to the toilet ventilation tube. As the owner, you have the ability to take care of the simple problems that can make the sucking sound. You may find, however, that the problem requires the experience of a plumber.



KOHLER K-4325-L-0 Kingston(TM) Wall-Mounted 1.6 or 1.28 GPF Flushometer Valve Toilet Bowl with Top Inlet and Bedpan Lugs, Without Seat, White White

clogs

A partial clog in the toilet drain line can result in the toilet making a sucking sound each time it is discharged. The clogging in the toilet drain line traps the air behind it, which leads to strange sounds, and even bubbles going up the toilet drain and into the container. If sinking the toilet does not dislodge the clogging of the drain pipe, turn to an endless closet for help. The auger's flexible line is fed through the drain line that curves the toilet bowl and pushes the blockage, or the hook at the end of the auger catches the clog and pulls it out of the leak.

Inadequate ventilation

Your toilet's drain line connects to a vent pipe, which performs a dual function. The ventilation pipe extends vertically up through the roof of the house, where fresh air is introduced into the old pipe as the air in the lava tubes down with the waste water. The vent pipe also transports the sewer gases into the pipes safely away from the house. A problem such as an obstruction in the ventilation tube leads to inadequate ventilation and suction sounds when the water is washed down the drain. Water demolition of the roof vent pipe, using its hose, should dislodge most of the obstructions in the vent pipes. A flashlight should allow you to see if there are blockages in the vent pipe, and see any progress you make in removing an obstruction.

Vent pipe damage

While you are throwing water down the vent pipe, have someone or several people in the house looking at the walls and ceilings to detect any signs of water leaks. If they detect any leak, they tell you immediately so you can stop shooting the water through the vent pipe. A leak indicates the ventilation pipe has a damage that affects the correct operation of the pipe.

Professional Help

If you see a nuisance and can not be removed, a professional plumber can help. The plumber has tools that reach the ventilation pipes and either push the obstructions out of the way or remove them. A plumber can also help if there are no problems with the vent pipe and yet the suction sounds continue. Plumbers have a machine that creates false smoke, which allows them to see where the obstructions or breaks in the vent pipe are located.

Danze DC013230BC Orrington Elongated Toilet Bowl with Soft Close Seat, Biscuit (Bowl Only)

Problems with a toilet

The toilet, without a doubt, is one of the most important aspects of your home, which can make extreme conditions when it is not being washed properly. Toilets are not terribly complex machines, and any washing problem can usually be diagnosed and fixed, either with a plunger or a quick trip to the hardware store.



Danze DC013230BC Orrington Elongated Toilet Bowl with Soft Close Seat, Biscuit (Bowl Only)

partial discharge

A weak fin could be the reason that your toilet flushes only partially, taking only about half the water in the container. The fin is a rubber device that "fins" in the toilet tank and covers the discharge valve between the tank and the bowl, which is where all the water drains when the toilet flushes. The fin should remain open until about 80 percent of the water has been drained from the tank, and then fall back down again. The fin, however, may decrease early if it is flooded, which prevents the rest of the water from escaping and keeps the wash bath complete. A new fin can be purchased at any hardware store and simply changed to solve the problem.

Phantom stuffing

Phantom filling is when the tank is filling with water constantly, even when the tank was not flushed. You will hear the characteristic sound of a "running toilet." This condition will make your flushes weak, as well as sewage. Phantom filling can result from a cracked fin that allow water to escape into the container instead of shut off. Replace the flap to remedy the problem. This condition can also be caused by a badly adjusted float, which causes the water to run down continuously from the toilet overflow tube and the filling valve does not close. Adjust the float so that it rises to the proper level and the fill valve goes off.

Jam

An obstruction is one of the most common problems with toilets. Clogs, can occur if too much toilet paper is used or if something strange, such as a comb or trash, is thrown down the drain. The sure sign of an obstruction is when a toilet simply does not discharge; when the discharge lever is pulled. Water will fill the container and sometimes spill on the ground. The solution is to use a plunger to aspirate what may be the cause of the obstruction. Sometimes, the obstruction can be remedied immediately, but other occasions will require the use of a hygienic snake or the services of a professional plumber.

Slow filling

Slow filling is when the toilet tank takes much longer to fill than normal, which means having to wait a long time between flushes. The filling valve regulates the water that enters the toilet tank. A floating device is used which, when it reaches a certain height, closes the valve so that the water does not overflow. The fill valve may have internal obstructions and will have to be replaced if the tank takes too long to fill. Filling valves can be purchased at hardware stores and easily changed. Just remember to close the water beforehand or it will come in spurts when the broken valve is removed.

KOHLER K-4309-96 Cimarron Comfort Height Elongated Toilet Bowl with Class Five Flushing Technology, Biscuit

Problems with two toilets

Two toilets are a preferred option for people who want or need to conserve water, but are concerned about the functionality of many low-flow toilets. According to Lowes, two toilets can reduce water consumption by 60 to 80 percent compared to older high-volume toilets. While double discharge models can make a big difference in water consumption, they are not without problems. Knowing the potential disadvantages of a double flush toilet can help owners make the right decisions about their bathroom remodeling.



KOHLER K-4309-96 Cimarron Comfort Height Elongated Toilet Bowl with Class Five Flushing Technology, Biscuit

Jam

According to John Eakes, two toilets and other flow models often clog, especially when installed in sewage systems that were not designed for them. This problem is most common with siphon toilets installed in bathrooms that do not see much use, such as a guest room. Washdown toilets may require more cleaning, but they do not tend to clog so often. Two toilets of all kinds work well when they are installed in bathrooms that see a lot of use as frequent washing prevents more waste material from accumulating in the drain pipe.

cost

Two toilets cost more than traditional individual toilets, due in large part to the lower demand for this style. As of 2010 and according to the Green Start Guide, two toilets start at around $ 175, compared to individual toilets that cost less than $ 100. Fortunately, the manufacturer competition and an increased demand for effective, conservative toilets of water is bringing little by little the models of double discharge down near the price of the most conventional baths. Two toilets also save water over time, resulting in a lower monthly water bill. It may take some time for this savings to pay off the difference in the initial cost of fixing though.

Cleaning

According to Lowes, dual-frequency toilet models require more cleaning and are harder to clean than standard single-flush models. These toilets retain less water in the container, which can result in increased dirt. It is also necessary to ensure that the water wells along the edges do not clog as this may decrease the ability of the toilet to function.

Plumbing Incompatibility

New residential construction takes the needs of flushing toilets into account, but dual flush models are not always compatible with old homes built when flush toilets were the norm. In addition, older plumbers have developed falls, sauces and other problems that prevent a double-flush toilet from working. Homeowners affected by the compatibility of their pipes should speak with an experienced professional before choosing a double-flush toilet.

Gerber Plumbing 21-372 Gerber Ultra Flush Watersense Elongated Toilet Bowl Only, White

Advantages and disadvantages of the two toilets

The purchase of a toilet is much more complicated than it used to be. Instead of having only one basic type of toilet to choose from, there are numerous toilet styles made by many manufacturers. The double flush toilet is a style that is being imposed for environmental and financial reasons.



Gerber Plumbing 21-372 Gerber Ultra Flush Watersense Elongated Toilet Bowl Only, White

Advantage - Environmental Impact

Dual-flush cisterns have a two-configuration activation mechanism that uses either a two-position lever or a two-button system. This allows you to decide whether or not you want to use a high volume color of water or a low volume color. The ability to use a smaller amount of water, when only washing away liquids allows you to ultimately save as much as a gallon and a half of water in each of the hot flashes, reducing your home's water consumption.

Advantage - Cost

In addition to the environmental boost for water savings, this also reduces your water bill over time. Dual discharge cisterns are also considered high efficiency. This means that some states have discount programs in place that help people subsidize the cost of upgrading the toilet in their home to a model that uses less water. Certainly, if you have this kind of bonus in your state, installing a double-flush toilet in the home will be more affordable than buying an old, non-efficient model.

Disadvantage - Cleaning

If you buy a double-flush toilet, you should expect to clean more often than you had to clean the standard toilets. The reason for this is that after each discharge, less water remains in the container. The toilet will start to look dirtier faster than standard-flush toilets do.

Disadvantage - Cost

Dual-flush cisterns are more expensive than the other options you could choose. Certainly, they are more expensive than a standard toilet. Both the cost of the purchase and the installation cost are higher than that of a standard toilet. A double-flush toilet, however, is often more expensive even than other high-efficiency toilet designs.

American Standard 3189.016.020 Colony FitRight Elongated Toilet Bowl, White (Bowl Only)

How do the two toilets work?

While most of us do not think much about bathing at the base of day to day, these accessories are a must. As we become more aware of how our actions impact the environment, more people are interested in the use of environmentally friendly products. The double flush toilet is one of those products. However, many people are curious about how well two toilets work.



American Standard 3189.016.020 Colony FitRight Elongated Toilet Bowl, White (Bowl Only)

How do the two toilets work?

Two toilets are designed to reduce the amount of water that is used each time a toilet is flushed. Two toilets differ from standard toilets in that they give users the ability to remove different amounts of water, depending on the type of waste that is emptied. Two toilets use less water to remove liquids than they do to remove solids, but both types of blushes use less water overall than standard toilets do.

Saving water

One thing that two toilets do very well is to conserve water. Some old style toilets use up to 5 gallons of water each time someone flushes. However, with two toilets, this number is drastically reduced. For example, washing the liquid waste in a double-flush toilet uses only one gallon of water or less. In addition, when solid waste is washed with a double-flush toilet, only 1.6 liters of water are used, which means it has the potential to hold more than 29,000 gallons of water each year if you change to a toilet double download of a traditional time.

Energy savings

A study conducted by the Canadian Mortgage and Housing (CMHC) monitors how well two toilets work, placing them in different homes, institutional and commercial environments. The study found that when two toilets were used in private residences, the discharge rate was reduced by 68 percent. In addition, blush rates in commercial companies dropped by 52 percent, while those of institutional facilities decreased by approximately 56 percent. While this conserves water, it also conserves energy. Each time a stool is emptied, the energy is used to pull the chain. Therefore, two toilets also work well in reducing energy.

Customer satisfaction

While it is good to know that double-flush toilets are ideal for those who want to go "green" for water conservation and energy reduction, many others are more concerned with how well two toilets work for the consumer. The same study conducted by the CSMC also examined the overall customer satisfaction of those who used two toilets. Overall appearance and functionality were rated as "satisfactory" or "good" in more than 85 percent of users. As a result, more than 66 percent of people said they would recommend double-flush toilets for others.

SANIFLO SANIACCESS 3 UPFLUSH MACERATOR PUMP + ELONGATED TOILET KIT, WHITE FINISH

How do toilet cleaners work?

Commercial Toilet Bowl, Cleaners

Some toilet cleaners use bleach, which will create toxic fumes when chlorine comes into contact with ammonia (urine contains ammonia). Other toilet bowl cleaners create a frothy, amorphous mass that rises when it hits the water in the toilet bowl. The foam is a concentration of bubbles that flush the toilet continuously bouncing against the surface of the toilet bowl. Blue liquid toilet cleaners operate more slowly than foam cleaners, and are made of chemicals that break down the deposits of dirt and minerals in the toilet bowl.



SANIFLO SANIACCESS 3 UPFLUSH MACERATOR PUMP + ELONGATED TOILET KIT, WHITE FINISH

The two most common types of bathroom cleansers are made from acidic or alkaline chemical ingredients. Acid cleaners contain phosphoric and citric acids, as well as alcohol, citrates and anionic or nonionic surfactants. Alkaline cleaners are made of sodium / hydroxide / hypochlorite carbonate, anionic / nonionic surfactants, citrates, glycol ethers, alcohol and sodium. Ammonium compounds are widely used in cleaning products of toilet bowls.

Acid cleaners

The soda can be used to clean the bathrooms. The acidity of the non-alcoholic beverage will eat away the dirt and minerals in the toilet bowl. Tail products are often used to clean the wheel bearings of the skids, and make a powerful bathroom cleaner. Soda pop is effective in the filth of eating on the plate. The lemon juice will remove the films and dirt, and weaken the mineral deposits in the toilet bowls. Toilet cleaners that are made of acids can be a liquid or powder. Acid powder cleaners (sodium hydrogen sulfate) work well for cleaning at night, because dust sticks to the inside of the toilet bowl. Unlike dust, acidic liquids (hydrochloric, phosphoric and oxalic acid) move slowly towards the hole in the toilet, bringing the dirt and mineral deposits with it. Quaternary ammonium chloride quaternary germicides in liquid bath cleaners, which should not be mixed with products containing chlorine (such as toilet bleach). The dye is included in liquid bath cleaners to alert the consumer that the acid cleaner is present in the toilet.

Cleaner Natural alternatives

Some natural remedies to clean the toilets are also effective, and do not include some of the toxic chemicals found in the trademark to clean the toilet. A homemade toilet cleaner is prepared from 2 tbsp. of baking soda, 1 tbsp. of olive oil and 1 teaspoon. of lemon juice. A simpler alternative, however, is white vinegar; It works best if you sit on the toilet and let it sit for 2 hours in a relatively clean toilet, or up to 24 hours for heavily soiled toilets. The same vinegar treatment is used to remove rust from old, corroded toilets, bathtubs and floor drains.