How to replace a Kohler toilet tank

How to replace a Kohler toilet tank

Kohler toilets are one of the most popular toilet brands in the United States. They are well manufactured, efficient and come in a variety of styles. However, even Kohler toilets will suffer wear and tear. Replacing a defective part of the toilet, like the tank, can be simple or require a little more time, depending on your Kohler model. You can quickly change a Kohler two-piece toilet tank. But you will have to take out the entire toilet to replace.

Toilet Bowl Ring Remove Product

Two-piece toilet
Turn off the water supply in the wall. You can find the shut-off valve by following the inlet hose from the tank to where it is connected to the wall.

Unload the toilet to remove the water. Wipe off any remaining water with a sponge and towels.

Unscrew the inlet hose.

Separate the Kohler tank from the base by unscrewing the two bolts inside the bottom of the tank. On most models, the bolts inside the tank have a screwdriver head, which allows you to use a screwdriver to keep the bolt stable while unscrewing the nut at the other end with a wrench. Or you can keep the key firmly on the nut at the bottom and unscrew the bolt.

Remove the bolts and washers. Gently lift the tank and out of the way.

Install the new Kohler toilet tank as you align the two bolt holes in the tank with the holes in the bowl and align the tank gasket with the inlet port in the bowl.

Pass the bolts and washers back into the tank holes once the tank is in place. Screw the nuts and washers onto the end of the bolts and tighten by hand.

Tighten the nuts a few turns with the key. Turn on one side and then on the other. Alternate the sides to maintain even pressure.

Add a few drops of glue or plumber's tape to the water inlet connection in the tank. This will ensure a tight connection. Then screw the water inlet hose. Squeeze with a wrench.

Turn on the water and allow the toilet to fill. Check for leaks.

One piece toilet
Turn off the water supply, clean the water and disconnect the hose following the steps above.

Unscrew the bolts at the base of the bowl that hold the toilet to the flange.

Gently shake the toilet back and forth to loosen it from its fit. Then lift it up and out of the way.

Wipe the remains of the old wax ring on the flange and install a new wax ring in place.

Insert the new flange bolts into the flange.

Turn over the new Kohler toilet. Add a thin strip of putty or plumbers putty along the bottom of the tank. This will help ensure an airtight seal between the cup and the floor.

Lower the new Kohler toilet into the wax ring, making sure the flange bolts seat through the holes in the base.

Press the toilet gently on the flange to make sure it is positioned on the ring.

Thread the nuts and washers onto the bolts on the bottom of the toilet. Hand tighten, then squeeze one side at a time with the key.

Things you will need

• New tank
• New one piece toilet
• Towels and sponge
• Wrench
• Screwdriver
• Plumífero, adhesive tape and putty
• Wax ring
• Disposable gloves

Tip

• The above steps are a guide to use in conjunction with the manufacturer's instructions.
• Warnings
• Do not over tighten the nuts or the porcelain could break.
• When cleaning wax rings, wear gloves; This part of the bathroom is full of harmful bacteria.

How to repair a toilet seal

How to repair a toilet seal

If you're wondering how to repair a seal toilet, you do not need to be worried since this is a simple repair job that can be done easily with some basic household supplies. Broken or loose toilet seals are among the most common causes of a leaking toilet. The toilet seal in most contemporary bathrooms is a ring-shaped seal that has an adjustable collar for a tighter installation. This seal is necessary to prevent the leakage of water and sewer gases that can contaminate the bathroom space. You can use the following guidelines to repair your toilet seal in an affordable and non-demanding manner.

Toilet Bowl Ring Remove Product

Step 1-Starting
Start by getting ready with a pair of rubber gloves. Turn off the shut-off valve or main valve that controls the toilet water supply. This valve is usually located on the wall on which the toilet cistern is secured. Rinse the toilet several times to make sure that the remaining water also drains. Now proceed to the base of the toilet, that is, where the toilet is secured on the floor of the bathroom.

Use a flat-bladed screwdriver to round the putty or putty ring. This can be tedious since the base of the toilet is well compacted at the time of installing the toilet. Use the tip of a screwdriver to open the plastic caps on each side of the toilet seat. Under the covers, you will find metal bolts that secure the toilet bowl on the floor. Loosen these bolts with a wrench and remove them.

Step 2-Dismantling the toilet flange
It is best to seek help from another person at this time to hold and lift the toilet bowl. Sometimes, the toilet bowl is not properly secured on its base and loosening the flange can cause it to fall off suddenly. Spread some old rags around the base of the toilet before attempting to tilt the toilet bowl. Ask your assistant to slowly tilt the toilet bowl. This could also cause a small waste of water retained in the toilet flush outlet along with traces of dirt for which the rags are made. This should reveal the flange bolt with the nuts that accompany it. The flange is a durable accessory, necessary to secure the toilet bowl in the underlying drain hole. The flanges are made of different materials, including cast iron and plastic. Metal flanges are difficult to handle as they can corrode. Use a sharp end of a screwdriver to remove rust. Use a wrench to loosen the nut and remove the bolt.

Step 3-Replace the toilet seal
It is best not to remove the toilet bowl, as adjusting it again could be difficult. Ask him to partner to keep the toilet bowl tilted as he goes through the repair. Using a spatula, edge the old wax ring. Replace it with the new wax ring. The seal of the wax ring should be adjusted. The new wax rings tend to protrude a little, which could damage the tight fit. Therefore, press down repeatedly on the seal. Now move towards the insertion of the flange bolts. Use a wrench to tighten the bolts.

Step 4: repair of the toilet board
Ask your associate to gently place the toilet bowl in its original position. Doing this with a tug can break the underlying ceramic tiles of the bathroom floor. Insert the metal bolts to secure the toilet bowl on the floor and tighten them with a wrench. Replace the plastic caps that you had removed at the beginning of the project. Finally, apply a thin layer of putty around the base of the toilet for a tighter fit.

How to wash the toilet? How can I clean a toilet?

How to wash the toilet? How can I clean a toilet?

To wash the bath Cup it is recommended to perform the following steps:

Toilet Bowl Ring Remove Product

1. Pull the handle from the TOILET and let the water run clean.


Como puedo limpiar bien un inodoro2. If using any product, apply and let stand for the time indicated on the label.


3. Brush very well, even on the water discharge flange and around the inside sides.


4. Let the water run again, and rinse the brush at the same time, shake very well and put it back in its base.


5. If the scale cannot be removed, apply muriatic acid (in half a bucket of water, two cups of acid and size with a broom or toilet brush), if you do not want to use the acid, tállela with a moistened water sandpaper.

Leaks in the toilet

Leaks in the toilet

Leaks on the outside of the toilet are easy to detect, but to solve them often it is necessary to dismantle the sanitary

Leaks on the outside of the toilet can cause significant damage and seepage across the floor. The advantage in this case is that water losses are easily detected. Sometimes problems are recorded in the area that joins the cup with the ground. Other times, leakages originate from watertight gaskets in poor condition. In many of these cases, it is necessary to dismantle the toilet or cistern to make repairs.

Toilet Bowl Ring Remove Product

 Problems between the toilet and the cistern

In order to solve the problems of water loss between the toilet and the cistern, it is often necessary to dismantle the latter to replace the sealing gasket and sometimes it is also possible to remove the fixing screws and the mechanism of the cistern. You have to take note of the deposit mark to buy a kit with all the necessary elements for the repair.

Then, the foam gasket is removed that allows the watertightness between the toilet and the cistern, the edges of the hole are cleaned to remove the lime scale and the new mechanism is inserted into the cistern. On the outside, the PVC nut is placed on the thread and locked to compress the gasket. Finally, a new foam gasket is installed on the nut and, again, the cistern on the toilet.

Leaks in the evacuation tube gasket

When leaks are recorded between the evacuation tube and the toilet, the latter must be disassembled. To do this, close the water stopcock, empty the cistern and disconnect the water inlet pipe to the cistern. Then it is separated from the wall and the clamping brackets are removed. To release the toilet from the floor, remove the screws that fix it. After unscrewing them, the toilet is carefully balanced to loosen the adhesive that binds it to the pavement.

    When leaks are recorded between the evacuation tube and the toilet, the latter must be dismantled

Sometimes the solution is to replace the seal gasket. In this case, after removing the toilet, remove the damaged gasket and cut the adjustment ring with a hacksaw. A new ring and elastomer gasket are then placed in place. Finally, just pull the ring to immobilize it in the neck of the tube and place the toilet in place.

Leaks in the bottom of the toilet

As time passes, water leaks can be recorded through the bottom of the toilet. Sometimes the escape is so scarce that it is barely noticeable. It may occur that the seal that joins the Cup with the floor has worn out and that this causes small puddles of water around the toilet.

To avoid the formation of moisture, fill this gasket with silicone or plumber's putty. This last product has a yellowish color that can be somewhat tarnished, so it can be painted with the same paint that is used to coat the joints of the tiles.

5 tips to eliminate lime: the best products

5 tips to eliminate lime: the best products

Lime can be a nightmare: it accumulates in the washing machine, in the taps or in our bathroom. Discover how to restore the brightness of your home.

Toilet Bowl Ring Remove Product

There are many ways to end the lime, however, we recommend the use of specialized products; There are different brands and different uses for these products: to remove lime from household appliances such as the washing machine, to leave our taps gleaming, or to finish with lime in the bathroom.

We tell you 5 tips to remove the lime permanently and we recommend the best anti-cal products on the market according to their quality-price.

Why lime is formed

Water often accumulates in cracks: between the tiles, the tiles, the faucets, the washing machine ... This water evaporates, however, its mineral residues remain.

The gradual accumulation of these mineral residues is what we call lime, which, in addition to being an accumulation of waste, offers a non-aesthetic appearance (a whitish layer that removes all shine from our tiles, sinks and appliances).

We will share with you some very useful tricks to eliminate lime in different areas of the house.

How to remove lime from the bathroom

In the toilet many bacteria are produced, therefore, a thorough cleaning every week is the best way to keep your bath hygienic and clean.

In addition to cleaning the toilet with your cleaning products, be sure to apply an anti-scale product inside the toilet bowl. Spray it with an anti-limescale product and let it act for 10 minutes. After that time, pull the chain and the water will clean the remains of the product.

Do this once a week, and if necessary, rub with the brush in the recesses in which a more visible amount of lime accumulates (once the anti-scale product has been applied).

As for the tiles, there is also the lime accumulates: being between the slits of the tiles, you must carefully apply the anti-lime product with a sponge or scrubbing pad; Leave the product to act for 5 minutes and rinse the remains of the antical with a wet cloth. Do not forget to dry the area when finished! We do not want to accumulate humidity!

How to remove lime from the tap

Removing lime from faucets requires more time; therefore, try to apply the product in a time zone in which you do not need to use that tap frequently, since you have to let the antical act for a long time (sometimes, depending on the amount of lime, can last for hours ).

To remove the lime from the tap and restore its original shine, soak a cloth of anti-scale product and wrap it with the tap in question. Another option is to rub the tap with the cloth, but in both cases it is necessary not to rinse the tap with water until after a while. If you wrap the tap with the cloth, do not remove it until after the actuation time.

With the shower head the procedure is the same, however, in this case it is advisable to disassemble the artichoke in order to reach all the nooks and crannies.

In all these cases, after time, rinse with water and dry carefully with a dry cloth.

How to remove lime from the washing machine

Cleaning the washing machine regularly is a guarantee of a longer service life and a better washing of your clothes.

Every so often (2 months, for example), fill the hot water washer and add one liter of anti-lime or bleach product to the dispenser.

With an operation as simple as this we make sure to keep our washing machine in perfect condition and a much longer durability. In the long run it means savings!

Better anti-lime products

The time has come for us to ask ourselves the big question: what is the best anti-calculus product? Which to choose?

Surely you already know some brands. We are going to recommend the brands with which we work, since, we believe, they are the highest quality for their optimal results and their effectiveness.

• -Calgon (gel)
• -Diranzio Bellido (anti-scale package for the lavavadora)
• -Codina (antical descaler)
• -KH7 (anti-scale gun)
• -Viakal (boat)
• -Viakal (spray)

Other options: salpumánico acid and phosphoric acid

There is the option to use acids to descale lime from certain areas, however, we recommend applying it with great caution, preferably by a professional.

The most commonly used acids are salpumánic acid (salfumán) and phosphoric acid. We recommend you learn how to apply them correctly before putting yourself to it for your safety and a more optimal result.

Have these tips been useful? Give us your opinion, and do not forget to tell us some other advice that you know and that we have overlooked :)

Come back to enjoy the original shine of your faucets, washing machine and bathrooms!

Toilet bowl top-features stripping

Toilet bowl top-features stripping

The problems in the toilet flushing system are not uncommon, however you can always fix them yourself, all you will need to remove the tank cap. Dismantling should be done carefully, as it may break or break. Therefore, in this article we will see how to remove the lid of a different type of toilet.

Toilet Bowl Ring Remove Product

General Information

In older models of drainage tanks, it is usually quite easy to remove the panel, simply unscrew the top of the trigger and lift it up. In modern tanks there is a drain button and a glass button, whose design prevents the dismantling of the cover.

However, in any case, this design is foldable, so this operation should not cause any special problem. The main thing is to do any action with care, without putting an excessive effort and slowly.

Before opening the toilet cistern cover, you must prepare some tools that may be necessary in the working process:

•     Pliers
•     Knife
•     Screwdriver

    Pay attention during operation with the tank, the water must be blocked. Otherwise, it can overflow and flood the bathroom.

Cover removal

At the beginning, it should be said that the lids of some models of modern ceramic containers are removed very simply, as the drain button is not connected to the trigger mechanism. To verify this, we must carefully try to lift the detail.

The following are ways to remove panels from other common types of tank designs:

•     If the water is drained as a result of raising the thrust, then before removing the toilet cistern cover, it is necessary to unscrew the ball located at the end of the handle.
•     Disassembling the container with drain buttons causes greater complexity, however, these models have become more popular recently. In this case, before opening the cover of the toilet cistern, you must unscrew the tube, inside which there are buttons. On the outside, it usually represents a ring, which must be pushed with a screwdriver or knife and turned counterclockwise.

It should be said that after this the panel cannot be completely removed, it can only be lifted and rotated a little, after which the latches of the button mechanism must be unfastened.

    The plastic tanks of the Soviet model, which are sometimes found in the apartments, have poles that must be removed before dismantling the structure with their own hands.


After the workpiece is disassembled, it must be placed in a safe place where it is impossible to hook and break it.

    Tip After repairing the toilet cistern drain attachment, it must be checked several times to operate. In particular, you must ensure that after lifting the float, the valve completely locks the water.

Cover Repair
Link

If in the dismantling process, something went wrong or the cover was broken for some reason, you can try to restore it.

For this you need to prepare the following materials:

•     Scottish
•     Epoxy adhesive;
•     Small galvanized steel plates.

The instructions for the implementation of this work are as follows:

•     First, all individual parts should be assembled in a single frame and taped. This should be done carefully so that there are no spaces where the glue can flow. To do this, all joints must be carefully taped.
•     Then the assembled structure should turn around.
•     Before gluing the toilet cistern cover, mix the glue with the hardener in a proportion of 1:10.
•     All gaskets should be carefully stained with glue and the galvanized plates must be attached from above, which will cause the product to become stiff.
•     When the glue hardens (about a day), the tape should be removed, after which the lid is installed in the toilet bowl.

Since the price of a new toilet is very high, this procedure will allow you to avoid the unplanned spending of family budget funds, while the appearance of the pipelines will not be affected.

Hole Increase

Often, home craftsmen, after replacing the drain fittings, face a difficulty: the diameter of the hole in the cap is smaller than the diameter of the reinforcement. Of course, you should not change the plumbing fixture completely, but how to increase the hole in the toilet bowl lid?

There are two ways to solve the problem:

•     Carefully drill the hole with a ceramic drill and cut out the remaining areas. The irregularities will be hidden by the cover.
•     Carefully chop the enamel with a thin drill and a hammer, then widen the hole with a round file.

In both cases, it is necessary to take great care not to divide the surface, because in this case it will be much harder to make a tank lid from the toilet bowl.

Here, perhaps, are all the main points you need to know to remove the tank cap and, if necessary, repair it.

Conclusion

The cistern cover of the toilet bowl, regardless of the type of construction of the latter, is removed quite easily. The main thing is to understand immediately what elements should be dismantled and not to make excessive efforts during work (see also the article: a toilet flush tank).

The video in this article will give you the opportunity to get additional information on this topic.

Installing a toilet

Installing a toilet

Installing a toilet is not a thing of the other world, just follow these simple steps, have a little patience and very careful and can do it easily.

Toilet Bowl Ring Remove Product

I imagine that you have the same thing happened to me once, we do an enlargement at home, for example an office, and logically we must have the toilets nearby so we do not have to cross the whole house, the ceramics are installed and then we call the Plumber , and oh surprise when we pass the bill to install a simple sink or a toilet charge us almost as we cost the same and of course no return to give we have to pay. Well, I started thinking about this matter when I finished the first bathroom of my house and decided to investigate how it is done, such a surprise when I realized that the work is as simple as "taking candy from a child" (if you please do not do that to children) , it requires that if enough patience and care.

Installing a toilet :

The first step is to acquire the toilet, do not think that they should go to the accessory store and buy the first one that comes or I like, this seemingly simple process has its complications and secret tricks; One is that they should consider saving the liquid element (for things like ecology), water is a precious and expensive, please ask them to buy toilets of 6 liters maximum, currently ay one piece models with this design; On the other hand and as more important step should consider the distance between the wall plated with majolica and the center of the sanitary outlet hole of four inches (or three if the case, although this measure is not highly recommended because it is prone to atoros) This distance should be at least 30.5 cms or 12 inches; Also the height of the outgoing drain pipe must be at least 1 cm. In relation to the finished ceramic floor . These considerations are important because not all toilets have the same measure; A variation in this matter would determine a bad fit of the sealing ring and the consequent leakage of water or annoying smells.

The good thing about acquiring modern toilets is that it already comes with the pre-installed internal accessories (for us as Bricómanos this is very convenient); Of course we must acquire other things like the water supply tube, this implement comes in several presentations: economical, usually with thread in ABS plastic and metal braided thread body less durable and I call premium, with Chrome-plated brass thread, aluminium braided body and inner reinforcement The thread size of this fixture must be 7/8 inch. We also have to supply two anchor bolts, these bolts are made of bronze and are instead of head with a removable nut to facilitate the fitting of the toilet base. A wax ring is the last implement for our project, this consists of a ring made of raw paraffin that in some presentations comes with a guide rubber that facilitates the fitting and installation (I recommend to buy in this type).

By hand all the above materials we proceed to install our toilet. A first step is to fit the toilet base into the drain hole, mark the places we drill with the drill (tip: use a 3/8 drill bit special for diamond-head cement, the hole must be previously Marked with a metal punch to avoid slipping of the bit), remove the base and perforate to insert the plastic anchors, the anchor bolts are screwed using a Stillson key (the movable head) or a self-pressure pliers (a tip: to mark the Hole location use indelible down, this if you paint on Majolica, the distance between the anchor bolts must be 16 cms. As a second step we turn the cup and fit the wax ring around the discharge hole at the bottom (tip: Do not place the toilet on the tile floor as it can chip, use the packing carton as Support). A third step is to fit the cup and adjust it with the nuts of the anchor bolts (A tip: they can "decorate" the head of the anchor bolts with ceramic plugs, sell them in the same health care provider and come in similar colors).


With the above steps we have already installed the toilet bowl or base, now we only need to fit the tank in place; To do this, simply turn the tank over and place the anti-leakage rubber that comes with the accessory kit and allow you to adjust the cup to the tank. The adjustment of the two parts of a toilet is carried out by the use OF ABS plastic regulating bolts (in modern toilets) or bronze (in the oldest), you should keep in mind that these bolts (which are placed from inside the tank) must go with their jebes to avoid leakage and in vertical position; Also be very careful in the placement of the tank, it must be positioned vertically and perfectly centered in relation to the cup (tip: Adjust the cup bolts by hand without using metal tools that can cause damage or breakage in them).

Good friends of "the housing market", we have installed our toilet, now we have to dispense with water, for this we taped with Teflon the supply tube in the part where the male thread and put a rubber inside the female thread; The male thread must first be placed in the water outlet of the wall (outlet usually ½ inch) once this is done adjust the thread on the outlet of the tank (tip: It is good to install a control key in case you miscarry a toilet accessory and cam is required Bio). Once all the above steps have been completed, seal around the cup with porcelain to make cleaning easier and prevent dirt buildup.

With these simple steps I believe without fear of mistaken that for you will be simple and gratifying to install a toilet, worth truths in these times always falls well save some pesetas and good there is no thing that makes us feel better than we do for ourselves.

How to remove cigarette burns in a toilet seat

How to remove cigarette burns in a toilet seat

• How to remove cigarette burns in a Kohler toilet seat
• Avoid cigarette burns from smoking in another room.

REMOVE THE CIGARETTE

Kohler toilet seats are made from a variety of materials such as wood, plastic and metal - none of which are completely immune to the damaging effects of a cigarette burning. Cigarette burns can stain the surface of your toilet seat, melt protective layers and burn directly through the base material. You can eliminate superficial burns on your account without professional help. However, deep burns require access to the base material and reapplying all protective coatings, which can be prohibitively expensive particularly if your seat has antimicrobial agents.

Toilet Bowl Ring Remove Product

What you need

• Gloves
• Rags
• soap holder
• Pad not to scrub
• Bathroom cleaner
• Put on rubber gloves.
• Moisten a cloth with warm water.

Pour a dime-sized drop of soap on the cloth. Rub the cloth against itself to form a soap scum.

Rub the cloth over the cigarette burn to remove debris on the surface. Place the used cloth in a bathtub or sink for sanitation or disposal.

Rub the stain with a non-abrasive sponge.

Rinse the entire toilet seat with a clean, damp cloth to remove soap residue.

Follow up with a multiple-use bath cleaner. Spray the cleaner on the surface of the toilet lid. Allow the solution to settle as directed by the manufacturer. Rinse the solution with a clean, damp cloth.

Tips and warnings

Examine the place after cleaning. If the surface of the seat has a visible gap or the cigarette burned and defaced the base material, it can safely be assumed that the protective layer has been removed.During the purchase of a new seat is easier, you can Refinish your current seat, if desired Use a high strength separation solution to remove the coatings from the seat then apply one or two coats of a high strength waterproof varnish.

Do not smoke in the bathroom or put cigarettes on the seat - the toilet seat is not an ashtray. If you can not quit smoking in the bathroom, purchase a cheaper toilet seat that can be replaced as needed.

Kohler advises against allowing chemicals to soak in the toilet seat for long periods of time.

How to clean calcium deposits from the toilet bowl

How to clean calcium deposits from the toilet bowl

Modern civilization would not be so modern without the toilet bowl. We no longer have to stoop precariously in dependencies or have disordered urinal contents. Actually, I think that running water outweighs almost any invention out there, including electricity. But it can still be more than a bit annoying when the toilets you greatly appreciate are victims of the dreaded calcium deposits. Fortunately, calcium spots are usually fairly easy to remove with a little effort and a hand or two solvent.

Toilet Bowl Ring Remove Product

Before you start in the "how" of the portion, it is always important to know some facts about the spots you are going to be attacking. First of all, "calcium deposit" is not code for anything serious. In fact, they are exactly what they seem--an accumulation of calcium and other minerals that are commonly found in your home's water supply. The bathroom is a prime spot for calcium spots because there is always some water hanging out on the plate, waiting to cause problems. Calcium spots accumulate over time, but they often feel like they appear out of the blue at night, resulting in an ugly brown/orange/pink ring around your toilet bowl once pristine.

Calcium deposits tend to be larger and worse in places with hard water or well water because there are more lime and minerals present in the water supply.

In fact, 85 percent of the water in the United States is difficult, so you're likely to face the stain more than a calcium in your life. Calcium deposits are not limited to the toilet bowl, unfortunately. They can run the water flowing rampant in any place, including the sink and shower doors, walls and shower. There are ways to keep calcium deposits from happening or get out of control. First of all, you can install a water softening system in your home.

Unfortunately those are seriously expensive, so you might not have space in your family budget. The cheapest (and most logical) method is probably just to cope with any calcium stain the instant it starts to appear. Like the tartar in the teeth, the longer you let it accumulate, the harder you will have to work to get rid of it.

If the container is already flooded with calcium stains, don't be afraid! Take a look at the following page for helpful tips on how to delete quickly and easily.

Calcium deposits are not all bad!
Of course, calcium deposits are unsightly in your bathroom and kitchen, but water containing calcium and magnesium can actually help you and your family reach some of your daily nutritional requirements!

Tips to remove calcium deposits from your toilet
Even if calcium deposits have established their residence in the toilet, there is no need to throw their hands in the air and buy a new one. Instead, use one or more of these techniques, and you're going to see some squeaky-clean results. Well, for a toilet, anyway. First of all, try the green route! A mild, natural acid, such as lemon juice or vinegar, can be very effective in pinching calcium deposits in the bud. Depending on the severity of the stain, the liquid may have to be re-applied and rubbed vigorously several times with sandpaper or rag.

Another option that many experts in DIY swear by IS plumber's cloth. Available at any hardware store, you can only use a single, plain water section to make stubborn stains disappear. If you don't mind some common household chemicals, pick up a bottle of commercial toilet cleaner for homework. Some users prefer to drain the toilet bowl first because it prevents the dilution water from the power of the VAC. Drop-ins tank are also effective in cleaning and preventing stains, although it might take some time to completely erase the stains from your bowl. If none of the simplest options are doing the trick, there are a couple of more risky ways to get the results you want. For example, muriatic acid can get rid of calcium deposits in a matter of seconds, but it is also very porcelain and dangerous to use if you do not know what you are doing.

First, be careful to make sure that the area is well ventilated due to the risks of smoke. Also, be sure to wear eye protection, rubber gloves, and clothing that covers your skin completely. Then, pour 5 gallons or less of water into the cup, followed by the careful addition of 12 ounces of muriatic acid. Then use a long-handled bath brush to carefully extend the solution around the stain. This step may have to be repeated several times during the next hour or two, but doing so must completely eradicate the mark. If you leave the room at any time, be careful to close the lid and safeguard that no child or animal can come into contact with water.

Another option of last resort is pumice stone, available in many dollar stores and hardware. Just use it with running water to wash the stain, but do it very carefully. Hard stone can irreversibly damage the porcelain, and you don't want to change one unfortunate look for another.

HOW TO CLEAN THE YELLOW SPOTS ON THE TOILET?

HOW TO CLEAN THE YELLOW SPOTS ON THE TOILET?

How many times have we entered a service, in a house or in some elegant offices and we have encountered those nasty yellow spots on the toilet, sometimes with a more intense color remarking the water level, if we knew how easy it is to get rid of They were sure that we had made them disappear for a while. The fact is, they're there and they don't look good.

Toilet Bowl Ring Remove Product

Materials:

• White vinegar
• Nylon Bath Brush
• Coke
• Bleach or Clórox (Bleach for Hispanic America)
• Sandpaper (for grandma's trick)

Note: Always wear gloves throughout the procedure and in the final part of the finish to clean the chair (which few people do) and around the toilet; At the end you should wash your hands when working in places in the home that may have more microbes.
Make the first step the night before.



TO REMOVE Stains Yellows TOILET Bowl:
1. Discharge the cistern and when the water settles and will not use it any more, pour a cup of white vinegar (this is the type of vinegar that has the expected effect) and let it rest overnight.

2. In the morning, scrubbing with the brush or nylon brushes, if you have gloves with a nylon brush will do a lot more strength against the stain, but some people still with gloves do not dare to put your hand inside the toilet bowl.

3. Pour a can of Coca Cola into the toilet bowl and let it sit inside for at least one hour. Unload the toilet and clean the toilet bowl and with a nylon brush the rest of the day use your bathroom as usual.

4. Pour a cup of chlorine bleach into the container and leave all night. In the morning, the stain will be gone.
Although it seems a little wasteful that spend two nights, it is very important to remember that these stains last years in the homes without anyone doing anything, the two nights make "loosen" the mark better.

5. If you see any traces, moisten a little Vanish on the brush and rub a little more vigorously.

Granny Trick to remove the water level mark in the toilet bowl:
Moisten a pumice stone without any product or foam so you can see well through the water and begin rubbing the stain gently with the stone; Make it very soft and without pressing too much, this solution is extreme and we know that the pumice is very abrasive and can scratch the toilet.

Thank you for consulting our easy and economical procedures.

Remove the yellow stains from the bathtub

After a long day it is nice to go home, rest and take a relaxing and warm bath. Soothes the muscles, soothes the mind and magically helps a stressful day fly away.

But how relaxing can your bathroom really be if you are greeted with unpleasant yellow spots? Yuck!

With a little help from Benjamin Franklin's PLUMBing Bay area, this DIY guide provides an effective method to clean a colorful tub – so you don't have to think twice about going into your hot tub!

Remove stains from the tub: follow these simple steps

Before jumping straight into the tub cleaning mode, it is important to consider the type of bathtub you have when it comes to bathroom PLUMBing.

You need to determine if it is porcelain, enamel or acrylic because you don't want to make the stain even worse by using an improper cleaning strategy!

If you have a porcelain bathtub, pour some Ajax or kite directly into the tub stain (enough to cover it completely). Add some water and rub with the abrasive side of a sponge. If you rinse the affected area and still see a defect, use a pumice stone to lift the rest of the stain.

If your tub is made of enamel, pour a generous amount of shampoo that you use for your hair directly in the dislocated area. Let stand for a few minutes, then rinse with lukewarm water. The stain should disappear since discoloration is probably caused by an accumulation of human oils that the shampoo can face.

If your house has an acrylic bathtub that has a stain or two, try applying a mixture of water and vinegar to the affected area. Then let it sit and suck for about 45 minutes. Continue soaking with a good sponge to rub and rinse with lukewarm water.

Fix flushing in the toilet

Fix flushing in the toilet

The toilet is one of the elements that can cause the most problems in the house. The most normal thing is that it gets jammed. However, leaks are also a common problem in these. Leakage from the outside of the toilet may cause damage, as well as seepage through the floor.

Toilet Bowl Ring Remove Product

The toilet is one of the elements that can cause the most problems in the house. The most normal thing is that it gets jammed. However, leaks are also a common problem in these. Leakage from the outside of the toilet may cause damage, as well as seepage through the floor. Other times, these leaks may have their origin in joints that may be in poor condition. To solve this type of problem, many times there is no other than to dismantle the toilet or the cistern in order to repair it.

If you notice that there are leaks between the toilet and the cistern , the latter must be removed to replace the sealing gasket. It may also be necessary to remove the setscrews as well as the cistern mechanism. Take note of the deposit mark to purchase a kit with all the necessary items for repair.

Then you will have to remove the foam gasket that makes it possible to seal between the toilet and the cistern. Cleans the edges of the hole to remove limescale and introduces the new mechanism into the cistern. Then, by the outer zone, you must place the PVC nut on the thread and lock it to compress the gasket. The last step will be to install the new gasket on the NUT, and again, the cistern on the toilet.

In the evacuation tube and the sanitary

Another problem may arise if the leaks are between the evacuation tube and the toilet. If this happens, you must dismantle the latter. To do this, you must close the water stopcock, empty the cistern and disconnect the water inlet pipe to the cistern. Then you must separate it from the wall and remove the clamping brackets.

In order to remove the toilet from the floor, you must remove the screws that keep it fixed. One of the solutions can be to replace the seal gasket of the cuff. In this case, after removing the toilet, remove the damaged gasket and cut the adjustment ring with a hacksaw. Once done, pull the ring to immobilize it in the neck of the tube and place the toilet in its position.

You can also find leaks at the bottom of the toilet. This can occur from the seal that attaches the cup to the floor. It may have worn out over time. To prevent moisture from forming, fill the gasket with silicone and ready.

TOILET SEAT FOR TOILET WITH SOFT CLOSURE SYSTEM

TOILET SEAT FOR TOILET WITH SOFT CLOSURE SYSTEM

In the universe of lids toilet seat, there is a wide variety of models. There are wooden, PL features and in both cases also different hardware options.

For these times the seat covers with soft closure or damped CA, are gaining ground against the AC da manual.

Toilet Bowl Ring Remove Product

A system in which the lid falls slowly towards the ring of the toilet causing a sense of harmony as opposed to the impact it implies when the manual descent fall, therefore have a better sound insulation. They are easy to install and remove because their upper anchorage allows the lid to be removed quickly if compared with the conventional fixing of screws and adjusting nuts. Its compact metal hardware gives it greater stability and a firm fit. The soft-closing lids are of Urea, a compact plastic material that impeccably confronts the humidity generated inside the bathroom without degrading the material over the years.

With these options we have other design variants, since these lids allow, by their manufacturing process, to intersect straight lines and curved shapes with total precision. At the beginning they entered the sanitary market in the high-end lines but today we can find them also in the models of medium range and soon Ferrum will launch this product for the lines of the low segment. A different touch that enhances the bathroom with originality and functionality.

Why resort to wax rings when there is a leak in the toilet

Why resort to wax rings when there is a leak in the toilet

Although there may be other effective solutions to stop water leakage in the WC, we tell you why to resort to wax rings.

Toilet Bowl Ring Remove Product

In toilets such as bathtubs, shower trays, bidets or toilets, which have been installed for a considerable time, it is normal for water leakage to occur promptly. They are usually caused by the deterioration that can be experienced by the joints or elements used to seal the joints between them and the drainage pipes that evacuate the water. So, if you perceive a slight loss of water in your TOILET, don't be alarmed, because it has a solution. Do not lose detail of what we are going to tell you, and find out why to resort to the wax rings when you encounter this mishap, and how to use them.

Why resort to wax rings when there is a leak in the toilet

The wax rings have been used for many years because they are perfect to seal the area where they are placed. In the toilet are located in the inner part, next to the ground, where the drainage pipe is located, in the junction between it and the sanitary, and they act by closing everything around it, to avoid the leakage of water and that gases and bad smells are filtered under the cup of the bathroom.

Although it adapts very well to the contractions, expansions and sedimentation of the soils, the material that composes it has a very long lifespan. The wax can be affected by temperature changes, hardening with cold and deforming or even melting with heat, and stop performing its sealing function. Therefore, if you have not changed it, it is advisable to be pending to detect any irregularity, in case it is time to do so.

And how will you know? Well, easily. When the soil area attached to the toilet has water, it is likely that the ring is in poor condition or deteriorated. You may also perceive a bad smell, like a sewer.

To access the wax ring you have to dismantle the toilet, so before you get into flour if you are not clear where the water comes from, you need to perform a check to make sure that that is the problem. With a natural dye in the cistern or sanitary tank and pull the pump you will know where the water comes out.

Once it has been confirmed that the filter is safely caused by the wax ring, you must replace it immediately to stop the water leakage.

Replacing a wax ring has its complication so, if you see that you're not able to manage by yourself, count on us.

In Morga cleanings We are experts in fixing any problems related to water leaks, pipe breaks and jams, and in conducting preventive maintenance of pipes and put to Point the plumbing facilities of households, businesses and commercial premises.

We also have an emergency service 24 hours, prepared to act in Bilbao and any point of Bizkaia the 365 days of the year. Because giving you assistance when you need it most is one of our priorities.

Do it yourself - How to install a toilet?

Do it yourself - How to install a toilet?

Changing sanitary devices or placing a new ceramic can transform radically not only the appearance of the bathroom, but also the lifestyle of the one who uses it. Therefore, if your TOILET is already worn, stained or broken change it can be an easy task to improve your environment.

Toilet Bowl Ring Remove Product

Tools and Materials
Tools to use:

•     · Caulking gun (for silicone)
•     · Paddle tip Screwdriver
•     · Banner of measuring
•     · Cross screwdriver
•     · Electric drill
•     · Bucket
•     · Concrete Drill
•     · French key
•     · Pelican Key
•     · Drill bit for ceramics

Materials to be used:

•     · Silicone with fungicide
•     · Non-stick resin tape
•     · WD40
•     · Wc

Print shopping list

Step by step
Before you start

Before you start
Before removing the WC, measure the distance between the back wall and the side screws at the base of the fixture, this will give you the measurement of the drain shaft on the floor.
With this measure choose your new device, selecting one that has the same axis or slightly larger.
Check all parts of your new TOILET.

Parts List:

•     Cup and Pond
•     Anchor screws to Floor
•     Full Tank valve
•     Tank-to-cup coupling seal
•     Pond fixing bolts to cup
•     Discharge handle
•     Flexible Water
•     Wax drain ring with plastic, integral verse
•     Seat
•     Stopcock (optional)

1
Remove existing TOILET.

    Drain the pond.
    Close the Stopcock (also known as the angular key) so that it does not pass
    More water.
    If there is no stopcock for the pond, or else you want to change it, close the key
    General step of the house and open some water faucets in other rooms
    To drain the whole system.

    Remove the TOILET chain so that the water flows into the bowl. Should not enter
    More water to the pond.
    Put a bucket to receive the water and unscrew the existing flexible key
    By the way.

    Remove the anchor bolts from the cup.
    Remove the pond from the Cup. This is not essential but it makes it easier to move.
    If the nut is rusty and very tight, apply WD40 or similar product
    to release it.

Recommendation
The TOILETs are heavy, take care of your back when lifting and moving.

Drain

Always try to use the same existing drain on the floor; Changing the position is complicated and quite demoro, and if the house has only one bathroom, it can become a real problem.
A change of drain implies-normally-more than a couple of working days: to break radieres or slabs, to cut existing pipes, to put a new section of pipe, to empty concrete again to close, etc.
And for all this it is advisable to hire specialists.

2
Install the new Cup

    Present the cup with your pond and mark on the floor the location of the perforations for the new bolts.
    If the location coincides with the above, remove the old anchors and put some new ones. Now, bolt the new.

    If the perforations do not coincide, these holes must be filled with cement.
    Once dry, drill two new holes with a ceramic bit.
    Insert new plastic anchors.

Cup position

To ensure that the outlet hole in the bowl is perfectly centered on the drain pipe, do the following:

1. Once the old Cup is removed, mark the shafts of the drain pipe on the floor.
2. Put the new Cup back down and mark on its base the axles, extend
On the side faces.
3. Place the new cup by matching the marked shafts with the floor strokes.
4. Mark the part contour on the floor and remove it.

3
Fit the wax ring

    Put the cup, without the pond, legs up (inverted) and carefully resting on a cardboard so that it is not scratched.
    Remove the protective cover from the wax ring.
    Fit firmly into the bowl drain.

To level
Sometimes the ceramics on the floor are not well leveled.
If this happens, put plenty of silicone on the edge of the TOILET base. This will help you level the position once it is set.

4
Seat Cup

    Turn the cup carefully and lower it until the wax ring is perfectly aligned with the floor drain.
    Press firmly into position.

    Clean out the silicone when pushing the cup against the floor.

    Screw the fixing bolts with their respective seals.

Installing Pond Parts

The inlet valve is installed with the separate 13 MMS float from the rear pond wall.

The discharge valve is installed facing the discharge tube.

5
Insert the inlet valve

    Screw the float to the metal bar.
    Insert the bar into the upper part of the valve and tighten into position by screwing.
    Insert the valve into the corresponding hole in the pond, making sure it has the seal in place.
    Notice that the float is separated from the walls of the pond.
    With a pelican wrench secure the locking nut. Do not overtighten the account.

6
Insert the discharge valve

    Insert the discharge valve into the central hole of the pond and with the locking nut secure it at the bottom.
    The vertical overflow pipe must be oriented towards the inlet valve.
    The top edge of the overflow pipe must be at least 13 MMS below the level of the handle perforation.

Recommendation
Be careful not to obstruct the placement of the two coupling bolts or the float bar.

7
Place coupling Seal

    Place the coupling seal on the threaded end of the flush valve, taking care to leave the tapered side down and the two aligned bolt holes.

8
Settling the pond

    Install the pond on the bowl and match the coupling holes.

9
Connect the pond

    Place the flat rubber washers to the bolts.
    Insert them into the holes in the pond by placing the metal washers and nuts on the bottom.
    Tighten the nut by hand, then hold it in place with a French spanner and tighten it from the top with a screwdriver.

10
Install the plug

    Remove the protection from the underside of the flapper or stopper.
    Connect the discharge valve and ears to the overflow tube in the location indicated.

11
Install the discharge handle

    Insert the discharge lever through the hole in the handle basin.
    Secure with locking nut, turning counterclockwise.
    The handle must be horizontal.
    Connect the knurled banner of the plug to the discharge lever.
    Adjust the length so that it rests completely on the discharge valve.

12
Insert the filling Hose

    Insert the filling hose into the overflow tube.

13
Connect the Flexible

    Connect the stopcock to the thread of the inlet key with a flexible water supply for WC.
    Tighten with a French key without exaggeration.
    Roll some non-stick resin tape into the thread of the nut or stopcock.

    Open the stopcock.
    The water level in the pond must be lower than the level of the overflow tube.
    Regular with the screw at the top of the inlet valve, this will force the float to go down in the water.

14
Seal Cup

    Seal with silicone around the bottom edge of the bowl and floor.

How to clean the toilet with Coca-Cola or soda?

How to clean the toilet with Coca-Cola or soda?

The bathroom is, without a doubt, the most bacteria-filled place in the home. There we wash all the time and when we have any accident, we run to the bathroom to solve it. But inside the bathroom is a site that is even more polluted, because it gets the worst load: the toilet.

Toilet Bowl Ring Remove Product

Our waste not only pollutes the toilet, but it gets dirty over time, and if we do not give a constant cleaning, can be a source of countless diseases, especially if you have children or dogs in the house that inadvertently, or wanting, put hands, legs , mouths and snouts in the water that Empoza in the toilet.

Although as much as we want and use products that promise wonders, it is impossible to leave it one hundred percent clean of bacteria; However, it is possible to keep it hygienic for safe use, as well as presentable to the eye so that it does not look like a gas station toilet.

The method we present below serves more than anything to whiten the toilet of that horrible circle of tartar in various brown tones that are formed inside by the water stagnant, but also leave your toilet sanitized for safe use On a daily basis.

Use of Coca cola or soft drinks

Cleaning the toilet with Coca Cola is one of the simplest, safest and most economical methods. The acidity of the soda, obtained from the phosphoric and carbonic acids that give it its characteristic bubbles, helps to take off the scale of the toilet, and the caffeine it contains helps to sanitize the toilet.

What are you going to need?

•     Coca Cola (depending on the size of your toilet you may need 1 to 2 cups of Coca Cola or any other dark soda)
•     Toilet cleaning Brush
•     Cleaning Gloves

How to proceed?

1. Pour the coke or soda in the toilet gently, making sure to cover the stains and the Tartar ring completely.
2. Let stand for at least an hour and a half the Coca Cola, without removing or using the toilet.
3. Put on your cleaning gloves.
4. Then moisten the toilet cleaning brush and scrub the stains and tartar ring. Everything will come out immediately.
5. Remember to pass the brush through the inside of the toilet.
6. Then pull the toilet handle and let the water take all the dirt you just cleaned.
7. Rinse the toilet cleaning brush.

He puts vinegar in the toilet tank. But watch when you pull the chain. That's great!

He puts vinegar in the toilet tank. But watch when you pull the chain. That's great!

Keeping the house clean can be a big challenge, and honestly, I'm one of those people who have a hard time keeping the house clean. I mean, it's not that I can't even know how to clean, but something always gets dirty and I don't have the energy to always be cleaning. So if you come to my house without warning, most likely this is something dirty and messy. You will find some clothes on the floor, dust on some furniture, and the bathroom? Ugh... The bathrooms are the worst!

Toilet Bowl Ring Remove Product

But I'm definitely not the only one who hates cleaning the bathroom. Ironically, with all the ugly germs that live there, the bathroom is probably the place you need the most cleanliness. So when I finally care and clean the bathrooms, what is the best and most efficient way to do it?

Thanks to HouseholdHacker, here is a video with 7 cleaning tricks for the bathroom to make it cleaner with the least amount of time and effort possible. And as if that were not enough, he uses a lot of articles that probably already tenhas in your house. These cleaning tricks include:

•     How to clean the mirrors with the newspaper and tea
•     How to remove water stains using lemons acid
•     How to wash unpleasant toothbrushes and soap dispensers in the dishwasher
•     How to use vinegar to clean the toilet
•     How to keep the toilet brush clean using a general cleaning product (this is great!)

To see all the details and more cleaning tricks for the bathroom, take a look at the great video below. And don't forget to share this video with your family and friends!

How to remove the lid of the toilet bowl

How to remove the lid of the toilet bowl

The problems with the toilet and the cistern are quite unpleasant in their essence. One of the most common problems is water leakage to the toilet through the tank. In this case, the question becomes relevant: how to remove the toilet cistern cover without damaging anything? Although the toilet designs of different manufacturers differ from one another, they have a general principle according to which we consider this problem.

Toilet Bowl Ring Remove Product

Most of the time, a button is found in the cisterns of the latest toilet models, which can be solid or composite. This is what prevents the cistern cover from rising easily. If the toilet is older, simply lift the lid. Sometimes it is necessary to remove the upper part of the trigger.

Many believe that the tank with the button itself cannot be disassembled. It is not difficult to open the tank, the main thing is to understand its design.

Tools Required

Before removing the tank, you must prepare the following tools, without which you cannot make repairs:

•     A pair of screwdrivers of different sizes;
•     You may need pliers.

• Instructions for new tank types.
• Nuevos tanques tipo

Then consider the tank analysis scheme in the example of the "Ido" tank manufacturer and similar with the plumbing fixtures:

•     Using a screwdriver, it is necessary to gently rotate the ring around the knob in the opposite direction of rotation clockwise so as not to scratch the top of the tank.
•     When the ring is moved, you can continue to twist it with your hands, without a screwdriver, it will no longer be necessary.
•     Unscrewing the ring, which must resemble the plastic cylinder externally, we recovered it.

•     After removing the ring, you can lift the lid slightly. In this state, turn it 90 ° so that it is on the other side of the tank; This position will remove the clothing clip located on both sides of the button. It's this clip for clothes and it holds the button.
•     The clamp must be unscrewed.
•     After removing the clothes clips, the tank cap will be removed without any problems. The tank is then repaired and its operation is checked without a lid. If all works well, the system can be assembled in reverse order.

    Tip Remove the lid from the tank, put it on something flat, preferably not under your feet and not on the toilet itself-a cover where the lid will not break so that it can be safely installed in the tank after repairs.

Retirar la tapa del depósito con dos botones.

And here's how you need to remove the cover from the tanks, which have double buttons:

•     First, press the middle button, then a small slot is found inside the other half.
•     With a screwdriver, you must cling to this slot and remove a portion of the button, after the disassembly you can get in the second.
•     In the hole you can see the slotted screw, which is part of the fixing of the tank cap; You must unscrew it.
•     After unscrewing the screw, it will be possible to lift the cover slightly and turn it 90 °. By analogy with the above instructions, you must remove the double-sided garment clamp, after which the cover will be removed.
•     By removing the lid in a safe place, you can fix the valve or leak and then collect everything as it was, but in reverse order.

    Tip When servicing the plumbing in the bathroom, be careful to remember the safety rules. In short, all the details of the washing mechanism during the repair work, which I will get, should be stored in a place where they do not fall out and get lost, nor under their feet. Be sure to make sure that access to these parts does not have small children and pets that can swallow or drag something.

Even before the start of the repair, the water supply to the tank must be cut, otherwise it cannot be prevented from filling during the repair of the system. Water can include only the one that repairs the drainage system, or the one that this person requests. In addition, water is usually only included to check the system, and once the person is convinced that everything is working properly.

Options to remove the covers.

Opciones para retirar las cubiertas.

Some models of tanks are made so that the cover can be removed without problems, because in such systems the button is not part of the cover. And what to do in cases where the above instructions are not adequate? Consider several options.

If it is not so easy to open the tank lid, you can try to unscrew the cork screwed into the mechanism responsible for drainage. Along the circumference of the button is a chrome-plated plastic ring, which must be unscrewed counterclockwise. It may happen that a small effort is not enough; Then you should apply a little more force while trying not to break the ring. However, most likely the button after a "strong" repair has to be replaced.

If, after lifting the lid, you can hear how the water drains, it means that in this design a chain is attached to the button, which is attached to the drain valve. You can remove the chain for convenience, but it is important to remember and note where it was attached to the valve. If this is not done, it will take a long and painful time to select the length of the chain for optimal drainage. When the chain is disconnected, it is safe and smooth to repair the tank.


The most important thing in repairing tanks is to remember to follow the advice given in this article and do nothing with brute force. The principle "There is strength-the mind is not necessary" is not for this case, because the force can damage the thin plastic elements of the drainage system.

How to remove the accumulation of minerals in the toilet bowl

How to remove the accumulation of minerals in the toilet bowl

That unsightly ring around your toilet is made up of hard water deposits. If your home has a soft water system, the toilet will be less likely to suffer from this accumulation of minerals. There are countless cleaning chemicals on the market designed to help remove mineral deposits. Instead of using aggressive chemicals, eliminate the accumulation of non-toxic, eco-friendly and low-cost household products.

Toilet Bowl Ring Remove Product

Instructions

1 Close the toilet water. This is typically a valve located at the base of the toilet.

2 pull the chain. When the water is turned off for bathing and washing, the water level must fall below the mineral ring accumulated in the toilet bowl.

3 Sprinkle baking soda generously over the mineral deposits in the toilet bowl.

4 white distilled drizzle vinegar over baking soda, so make a paste. Let stand for about 10 minutes.

5 rub vigorously with a toilet brush.

6 pour more vinegar into the mineral buildup and let stand for about 15 minutes before re-scrubbing.

7 Scrub the area with the bath brush to rinse the vinegar.

8 Scrub The ring with a pumice stone to remove a hard-to-build mineral, if necessary.

9 put the water back to the bathroom and flush to rinse the area.

How to remove rust stains from toilets, tubs and sinks 2019

How to remove rust stains from toilets, tubs and sinks 2019

If you have ever left a can of metal-based shaving cream on the shower floor, you know how hard it can be to eliminate the resulting oxide ring. Unfortunately, since rust stains can also appear as a result of galvanized pipes or mineral deposits found in hard, iron-rich water and well water, avoiding metal cans alone will not prevent the formation of rust spots on your fixtures. . The good news is that it is possible to remove rust spots in the bathroom without a lot of time and effort.

Toilet Bowl Ring Remove Product

For best results, eliminate chlorine-based bath cleaners, which can actually make difficult spots worse, and try one of these proven methods.

Barkeeper's Friend

Barkeeper's friend, both in powder and liquid, is an extraordinarily effective method for removing rust stains from bathroom accessories. Barkeeper's Friend will safely remove the rust stains and mineral deposits from all the toilets and finishes of the metal faucets. And, according to the manufacturer, it can also be used to remove stains from sinks, bathtubs and showers made of stainless steel, porcelain, Corian, refractory clay, ceramics, acrylic, copper, glass, enameled cast iron, fiberglass and solid surface materials.

Shaw pads

Shaw Pads offer a chemical and septic-free approach to removing rust. Equipped with a simple handle and a scrub cloth, Shaw pads work with the "fat elbow" principle: simply moisten the patch and brush the spots gently.

Use Shaw Pads to remove the rings from the toilet; accumulation of oxide, calcium and lime; gray, green and brown water residue; algae and chemical stains on the tiles of the pool; and hard water and well water waste.

Pumice Stick

Pumice scrubbers work especially well to remove rust stains from porcelain. Use Pumice brand bars to carefully remove mineral deposits, rust and other stains and scales from sinks, toilets, bathtubs and showers.

And, use them to remove rust and unwanted paint from metal work, pipes, tiles, masonry and concrete as well. Made of 100% natural pumice stone, these poles are safe for dermal contact and for use and storage around children and pets.

ZUD Scouring Cleanser

The ZUD cleaner employs oxalic acid and a powerful combination of fine ground quartz and pumice compound abrasives to remove rust spots on contact. Available in both liquid and powder form, it dissolves rust, mineral stains, hard water deposits and soap scum. And, according to the manufacturer, it can be used to clean copper, brass, bronze, chrome, iron, pewter and stainless steel. Simply spray or spray ZUD directly on rust spots and brush with a cleaning brush or plastic pad. Then, add water to cover, make sure the ZUD solution covers the entire area. Add more ZUD where the solution is missing. After the solution has been established for approximately 60-90 minutes, clean the area with the brush and rinse the solution.

The Works Limeosol

The main active ingredient in The Works Limeosol is hydrochloric acid, which instantly removes rust, hard water stains and mineral deposits from appliances, bathroom fixtures, cement, brick, vinyl, siding, fiberglass, PVC and others. materials in contact: no scrubbing is required.

The Works is tried and true: it has existed for more than 50 years. And, despite the fact that it contains a dangerous chemical, it has long been a famous favorite among homeowners and door-to-door service professionals alike. The Works Limeosol is not recommended for use with septic systems.

Prevents the rust from appearing again

•     Install an iron filter or a water softener. Because the oxidation of the bath is so often the result of hard water rich in iron and well water, the installation of an iron filter or a water softener will go a long way in preventing future stains. Generally speaking, these filters are easy to install, although they can cost more than $ 600.
•     Keep metal cans away from the tub and sink. When in contact with water, cans containing metal rings in their bottoms (for example, shaving creams, air fresheners, hairsprays, cleansers, etc.) will quickly oxidize and stain bathroom surfaces. It is best to store these items in a closet away from the bathtub and sink.

    Clean the bathtub and sink after each use. Rinse and clean the sink and bathtub after each use to remove any iron residue.

How to remove plaque from the bathroom quickly and effortlessly

How to remove plaque from the bathroom quickly and effortlessly

The tartar cleaning tricks you should know

Eliminating tartar is not a simple task, much less, but it is something you must do to keep your bathroom clean and prevent it from spoiling. The tartar over time eats the surfaces and ends up damaging them permanently, avoid this by doing a complete scale cleaning.

Toilet Bowl Ring Remove Product

How to remove tartar from the bathroom is a question that you have asked yourself more than once, I am sure of that. In all the bathrooms it is joined due to the presence of tartar in the water that is in contact with the bath surfaces, whether they are sinks, showers, toilets and even on the floor and walls. But all this is a thing of the past, since here you will find tips to eliminate tartar at home quickly.


Water scale is produced by the high concentrations of bicarbonates, magnesium carbonates and calcium it may contain. It is also known as hard water and is the cause of calcareous incrustations that are generated in pipes and bathroom elements, hot water tanks and others.

Scale accumulates as hard water circulates through the pipes and comes in contact with your bathtub, wash and toilet . The calcium that the water contains crystallizes , the crystals that are produced that adhere to the surfaces, being able to have destructive consequences in the medium and long term.

If you live in an area where the water is hard permanently, the best thing you can do is use elimination operations such as softening and softening the water . Anyway, once the damage is done or the water is hard only for ages you should remove tartar at home and there are different tricks that can help you in this task without damaging your surfaces .

The best tricks to remove tartar from the bathroom

Pipelines

The first step you must take is to clean the pipes in your bathroom. Since it is here where the scale passes to your toilet, walls, sinks and floors. How to clean a pipe is a simple task, but its solution is not permanent, you must carry out weekly or monthly cleanings to remove scale from pipes and avoid damaging your bathroom.

There are many tricks to clean your pipes, but these are the definitive ones: with vinegar or with salt, always accompanied by baking soda. Choose the one you want and you will be able to remove scale from pipes quickly.

•     White vinegar You only need three ingredients: bicarbonate, white vinegar and water to boil . Start by placing the baking soda in the pipe and then pour in the vinegar and hot water. Leave on for 15 minutes and throw in hot water again.
•     Salt. Mix half a cup of baking soda and a half of salt with a little hot water. Throw the mixture in the pipe and let it act for a whole night, without opening the taps.

Toilet

Water circulates continuously in the toilet or toilet, which causes large clumps of tartar to be generated easily. However, how to eliminate plaque from the toilet is a relatively simple task and with these two tricks you will definitely eliminate tartar from water.

•     Vinegar and lemon A cleaner of white vinegar and lemon will not only remove the tartar, but it will deeply clean your toilet, leaving a delicious citrus fragrance. Mix half a cup of white vinegar with a lemon juice. Apply with a cloth or sponge and let act a few minutes. Then clean the toilet with warm water to remove the tartar debris.
•     Cola drink. Surely you have already read on the internet that cola is used to clean pipes because of its abrasive power, because today you can take advantage of it. You need a can of cola drink, a cup of white vinegar and three tablespoons of baking soda . Start by pouring the soda into the toilet, let it act for half an hour and brush the surface, then add the vinegar and bicarbonate, it will generate an effervescent effect, let it act and rub again. Rinse with hot water.

Walls

The walls of the bathroom are usually stained with mold and moisture , but how to remove tartar from the walls of the bathroom is another problem that these can bring. Generally, the walls of the bathroom are covered with tiles, which makes cleaning easier, although they can also be painted walls. Here you will find a trick for each of them and thus eliminate tartar in the water.

•     Peroxide. If there is an effective ingredient for cleaning tartar, this is oxygenated water, as it can easily rinse surfaces. Mix half a cup of baking soda, two tablespoons of hydrogen peroxide and juice of a lemon . You can use this trick with care on the walls and with tranquility in the tiles. You must make a paste with all the ingredients, apply on the surface, leave on for 20 minutes and stir.
•     Vinegar. You can also rely on the power of vinegar to clean your walls, as long as they are tiled, as you could damage the paint. Apply with a cloth vinegar mixed with warm water, let it act 20 minutes and rinse with warm water again.

Handwash

If you use a lot of sinks and more when there is a small loss of water in the faucets, it is normal for tartar to accumulate. But do not worry, here you will find two tricks of how to remove tartar from the sink and you can start testing them right now.

•     Pumice. Moisten a pumice stone in warm water and rub over the parts where you see tartar. You must be careful to avoid damaging the surface.
•     Sodium bicarbonate. Mix baking soda with hot water until it forms a paste. Apply in the areas with tartar, let act half an hour and remove the remains with a sponge soaked in warm water to remove tartar.

Floors

Mainly when there is water loss or you have to clean a bathroom that has been abandoned for a while (as it happens when you move), the floors can be stained with scale. This gives an unpleasant aspect, but not anymore, because here you will find the best trick on how to remove tartar from the floor of the bathroom .

•     Borax. You need 1 cup of white vinegar, 4 tablespoons of borax and one liter of hot water . Start by passing the white vinegar mixed with hot water as if you were mopping the floor. Then add the borax in the areas where the tartar is concentrated (always use gloves, mask and ventilate the environment) and brush. Leave on for half an hour and rinse with hot water.
•     Sodium bicarbonate. Another option, if you do not want to use borax, is to replace it with sodium bicarbonate. However, if the problem is serious you should opt for the most abrasive option that is borax to remove hard tartar. If you want to use baking soda you can use four tablespoons or more if necessary .

Removing tartar from the bathroom is a task that can take time, but the best thing is that, although there are tricks recommended for certain parts of the bathroom, all can be used in the bathtub, floors, toilet, sink and tiles. You just have to be careful with the walls, since you could damage them and you will have to repaint them.

How to prepare a homemade tartar remover

As you have seen there are many home ingredients that will help you eliminate tartar . But here you will find the definitive recipe for a homemade tartar remover for almost all types of surfaces.
Ingredients

•     Half a cup of white vinegar
•     5 tablespoons of baking soda
•     Half a cup of hydrogen peroxide
•     A cup of hot water

Preparation

•     Mixed vinegar mixed with oxygenated water.
•     Then add the hot water (to the point of boiling) and finally the baking soda.
•     Store everything in a bottle or container with a lid and that's it, you have your homemade tartar removed.

More tricks for your bathroom

Removing scale in the bathroom is not the only challenge you will face when cleaning this area of ​​the home. Cleaning tartar is just one of the steps you must follow to have a clean bathroom. Here you will find more tricks so that each time you clean it, it will be shiny and free of odors .

•     For cleaning . Each part of the bathroom requires a different kind of attention at the time of cleaning. The bathtub, mirrors and toilet are not cleaned in the same way and everyone has their tricks to be gleaming.
•     For smells . If there is something that characterizes the bathrooms, it is the bad smell that they can lodge. But that is a thing of the past because there are some special tricks to eliminate the unpleasant smell and leave your bathroom with a delicious aroma.
•     For artifacts . Disinfect, clean drains, toilet lid and remove stains from surfaces are some of the actions you must take to keep your bathroom clean. Know the best ideas to make it perfect.