American Standard 3180.016.020 Townsend Champion-4 Right Height Round Front Seatless Toilet Bowl with Bolt Caps, White

How to repair a Sterling toilet tank

Water leaks in the floor around your sterling two-piece toilet can be attributed to a problem with the tank or in its internal functioning. The tank has a water supply in the list for the next discharge. The deposit may or may not need to be removed from the toilet bowl, depending on what type of repair is needed.



American Standard 3180.016.020 Townsend Champion-4 Right Height Round Front Seatless Toilet Bowl with Bolt Caps, White

Two-piece toilet

The Sterling two-piece toilet consists of a separate bowl and tank. The two pieces are separated by a rubber gasket and connected by three bolts and nuts. The reservoir is located at the top of the back of the cup. When the discharge handle is pushed down, a rubber flap on the bottom of the tank rises, letting the water in the tank fever over the cup. A float triggers a valve to open to allow the container to be refilled with water. Once the water reaches a certain level, the valve closes.

cracked tank

A broken or cracked toilet tank should be removed from the bowl for repair or replacement. Since the tank must be water resistant, it is difficult to repair a broken tank and do not have it leaked. Replacement tanks for Sterling two-piece toilets can be had for around $ 40 as of 2011. Total tank replacement can be a better long-term solution.

Damaged tank seal

A bad seal between the container and the tank can make you think you have a cracked tank. Unfortunately, the work requires the removal of the toilet cistern. Once the tank is removed, the mating surfaces in both the container and the tank must be cleaned so that the new gasket has a proper seal. The tank can be installed in the reverse order of extraction.

Tank mechanics

A perceived tank problem can be caused by the internal operation of the tank. Water leakage can be caused by a defective flap in the bottom of the tank. If the water is passed from the fin, the toilet valve will turn on to replenish the lost water. This will go on in an endless cycle until the trap is replaced. A leak in the bottom of the tank can originate from a cracked water control valve or the gasket that seals the valve to the tank. The valve threads protrude through the bottom of the reservoir to provide a place for the water supply line to attach to. The replacement of the internal parts of the toilet tank can be achieved without the need to remove the tank from the bowl.

Removing the deposit

Removing the tank may not be as hard as a job you may think. The first step is to close the water supply to the toilet. Most houses have a shut-off valve near the base of the toilet. If you can not locate a shut-off valve, you will have to cut off the main water supply to the house. Once this is done, the water remaining in the tank must be removed. Pulling the chain will evacuate most of the water. Any remaining water will have to be removed by absorbing it with a sponge or cloth. The water supply line can be removed from the bottom of the tank. Once the three screws of the holding tank are removed, the tank can be lifted up and out of the cup.

American Standard 3011.016.021 Cadet-3 Round Front Toilet Bowl, Bone (Bowl Only)

How to repair a leaking toilet tank

The toilet tank contains the water before rinsing. After pressing the discharge handle, the water in the tank is exhausted to the bowl and the distance colors of the wastewater. Because it is constantly carrying water, the tank has a lot of opportunity to leak. A leaking tank should not have to call a plumber immediately, however. Repairing a leaking toilet tank is something that even the average diyer can do on its own.



American Standard 3011.016.021 Cadet-3 Round Front Toilet Bowl, Bone (Bowl Only)

Instructions

1 Turn off the water in the supply. This is under the tank on the side of the wall. Cut the water by turning the knob clockwise. This will help prevent new leaks.

2 Unload the toilet to get rid of all the water inside the tank. Collect the extra with rags and sponges.

3 Disengage the water supply from where it connects to the tank.

4 Remove the tank from the bowl. The heads of the screws are in the lower part of the tank. Hold a screwdriver on their head while unscrewing the nut from below with a wrench. In most models, two bolts are holding the tank to the cup.

5 Set a towel on the floor. Carefully lift the tank from the cup and put it upside down on the towel.

6 Remove the cone gasket at the bottom of the tank. This is the part that connects the tank to the cup. Check this for leaks. Even if it is in good condition, it is a good idea to change these each year more or less. Replace the cone seal or replace it with a new one.

7 Check the rubber gaskets on the bolts. As with the cone gasket, they can deteriorate over time. Replace those that are cracked or broken.

8 put the tank back in the cup. Make sure that the cone seal is correctly aligned with the hole in the container.

9 loosen the screws and rubber washers through the holes in the bottom of the tank and through the container. Tighten the nuts of the tightened hand, and then an additional turn with the key.

10 Wrap a strip of plumber's tape around the water inlet in the tank. This will help prevent the water supply from leaking. Squeeze the water hose in the inlet, the hand tightened at first, and then use a wrench.

11 Open the water supply and allow the bath to fill.

12 Pull the chain. Check for leaks around the tank.

Tips and warnings

•     Be careful not to over tighten the nuts around the toilet, as this could break the porcelain.
•     Do not try to repair a fissured toilet tank crack with putty. Replace the entire tank.

American Standard 3191.016.222 Colony FitRight Right Height Elongated Toilet Bowl, Linen (Bowl Only)

How to repair the chain in the toilet tank

If you press the handle of the toilet on the toilet and nothing happens, you have a problem with your toilet chain. The handle on the outside of the toilet tank is connected to a discharge rod that rises in response to the action of the handle. When this rod lifts, pulls a chain. Attached to the other end of the chain is the odorless fin. When the chain raises the fin, it allows the water inside the tank to escape and discharge. Repair of the chain in the toilet tank is a relatively simple operation.



American Standard 3191.016.222 Colony FitRight Right Height Elongated Toilet Bowl, Linen (Bowl Only)

Instructions

1 Close the water supply for the toilet that contains the chain you want to repair. The toilet supply valve is located on the wall behind the toilet. You should see a hose or tube that goes from the supply valve to the toilet tank. Turn the knob on the end of the water supply valve to the right to close the water.

2 Lift the lid of the toilet tank. Locate the toilet flap, which is the rubber stopper on the bottom of the tank. Normally, when the discharge lever is pressed, this raises the fin and allows the water to rotate out of the tank. This, however, will not be the case if the chain needs to be repaired. Reach your hand in the tank - do not worry, the water is treated - and grab the fin with your hand. Pull the tongue and allow the water inside the tank to escape.

3 Examine the chain and determine where the break occurs. A break in the middle of the chain can be repaired by reattaching the two halves of the chain back together with a piece of wire. If the break occurs, either in the discharge lever or the trap, replace these links as necessary, either with cable or by adding a replacement link. You can buy chain replacement links that slide over the flap or the dipstick as a car key ring.

4 Press the discharge handle and check that the chain opens and closes the flap when operating. Press the flap down on the flap opening at the base of the tank.

5 Restore the water supply by turning the water supply knob clockwise. Let the tank fill up.

6 Pull the chain and see the flap and chain. Make sure it works properly with the full tank. Replace the tank lid.

Tips and warnings

•     Some of the hardware stores sell toilet chain repair kits that have many of the replacement parts you need.
•     If the chain breaks in the middle, this repair is a good temporary solution. However, the chain must be replaced as soon as possible.

STERLING 403215-47 Windham Elongated Toilet Bowl, Almond

How to repair a filling valve of a toilet tank

The filling valve, as the name implies, refills the toilet tank with water after a wash. These accessories are controlled by a set of valve float. As the water level in the tank rises, it leads up to the float valve, which finally cuts off the water supply to the fill valve when it reaches a predetermined level. The best way to repair a fill valve in a toilet tank is by replacing the entire filling valve assembly. They are not expensive and the work is not complicated, even for a plumber for the first time.



STERLING 403215-47 Windham Elongated Toilet Bowl, Almond

Instructions

1 Close the water for the toilet cistern. Follow the water supply valve from the bottom of the toilet bowl to its confluence with the supply valve on the wall. Turn the knob oval on the front of the valve to the right to close the water.

2 Remove the tank lid and set aside. Download the bathroom. Hold the handle down after pulling the chain and allow all the water inside to flow out. Wipe away any excess with the towel and sponge.

3 To remove the valve float from the filling valve. In most cases, the valve float can be separated by removing the two wing nuts that hold it. This step is not necessary in a filling valve with an integrated float.

4 Place a towel on the floor under the tank. Unscrew the water supply hose from the inlet on the bottom of the tank with a pair of pliers. Loosen the plastic retaining nut on the inlet. Lift the old fill valve up and out of the tank.

5 Clean the area immediately around the filling valve base at the base of the tank. Use a spatula to scrape and remove any buildup of sediment or calcium. Apply a light coat of silicone grease on the perimeter of the socket.

6 Insert the new filler valve into the filler valve socket. Make sure the gasket is tight on the bottom. Keep this with one hand. With the other hand, take the retaining nut and place it under the toilet cistern. Screw the retaining nut onto the threads on the bottom of the filling valve. Tighten with the key.

7 Replace the float assembly, if present.

8 Wrap the inlet threads of the fill valve in the bottom of the tank with plumber's tape. Fix the water supply hose and tighten with the pliers. Reset the water supply by turning the water supply button counterclockwise. Allow the bathroom to fill up

9 Pull the chain and check that the new filling valve is working correctly.

Tips and warnings

•     Do not over tighten any of the retaining nuts or plastic couplings, as this could cause the plastic to crack.

Toto CT708EGNo.01 Commercial Flushometer High Efficiency Toilet-1.28-GPF, Top Inlet Spud, Cotton

How to install a filling valve for a toilet tank

With all the mechanical action that takes place in a toilet tank, it is not surprising that some of the internal parts will need replacement from time to time. If the toilet tank still works or did not work properly, it is time to replace the fill valve. It is not a difficult task, even if you do not have any plumbing experience.



Toto CT708EGNo.01 Commercial Flushometer High Efficiency Toilet-1.28-GPF, Top Inlet Spud, Cotton

Instructions

1 Cut off the water supply for the toilet and pull the chain to remove the water. It is also possible that at this time you want to clean all the lines and valves involved.

2 Remove the lid of the toilet tank. Using the sponge, remove more water still standing in the tank.

3 Loosen and remove the feed line from the bottom of the tank. Have your bucket ready to pick up the water that is standing in the old pipe or valve.

4 Remove the large retaining nut just above the power line at the bottom of the old unit, and remove the unit from the tank.

5 Clean the tank clean and dry, with the sponge before installing the new unit to remove any particles of grain or rust that could ruin the new seal or valve.

6 Set the new fill valve. Most new valves twist to adjust the height. You want to adjust to the highest point you can go without touching anything inside the tank. Now you just have to reinstall the new unit in the place of the old one. Make sure the float does not touch the sides or top of the tank or the ball valve on the bottom.

7 Install the overflow tube in the overflow tube. These usually only latch on top.

8 Install and tighten the unit retaining nut. Just tighten this nut enough to hold it - be careful not to break the porcelain. Wrap the threads on the end of the feed line of the Teflon tape unit and install the feed pipe and tighten. Do not over tighten this accessory as it is a plastic connection in most cases and can easily break.

9 Open the water again and pull the chain. If you do not discharge or refill correctly, you may have to adjust the height of the new fill valve by turning it higher or lower.

Tips and warnings

•     Great idea if you have more than one rental property, it will save you a few dollars in time.
•     Old plumbing tends to have sharp rusty edges sometimes. Be careful how to handle these elements.

TOTO C743E#01 Drake Round Front Bowl, Cotton White

How to replace the float valve in a toilet tank

When a hygienic float valve goes bad, that means that the tank can no longer hold water between discharges. As a result, the toilet is running constantly, which wastes a large amount of water and can lead to utility bills. Replacing the float valve is a simple home repair that requires only a few instruments and about a half hour of maintenance staff time.



TOTO C743E#01 Drake Round Front Bowl, Cotton White

Instructions

1 Turn off the water supply to the toilet bowl by turning the valve handle located behind the toilet. Lift the lid of the toilet tank and keep it in reserve. Pull the chain so that all the water runs out of the tank. Use a sponge to absorb any excess water left in the tank.

2 Place a towel on the floor at the base of the back of the toilet. The towel will absorb water that leaks from the toilet during the process.

3 Use a pair of pliers to disconnect the pipe from the wall to the toilet tank. Disconnect the hose at the end of the tank by loosening the plastic nut that connects the hose to the tank.

4 Switch to a spanner. Use the wrench to loosen the nut that holds the float valve in place. The nut is located near the area that the hose is fed into the tank.

5 Release the thin plastic tube inside the valve tank and lift the valve from the toilet tank. Discard the old valve.

6 Read the instructions that accompany the new float valve. Install the rubber grommets firmly into the hole of the float valve on the base of the tank. Insert the new float valve into the hole and carefully tighten the retaining nut on the bottom of the tank.

7 Reconnect the hose to the valve and connect the thin plastic hose inside the toilet tank to the valve. Make sure all stamps are in place. Open the water supply and see if there are leaks around the tube. Tighten the seals and the plastic nut, if necessary.

8 Look inside the tank, as it fills with water. If the valve is installed correctly, there should be no leaks and the water line should be about a half inch from the top of the tank.

KOHLER K-4304-L-0 Highline(R) Toilet with Pressure Lite(R) Flushing Technology and Bedpan Lugs, White White

How to replace a toilet ball valve

Combined with a float ball that rises and falls with the water level, the ball valve directs the flow of water into a toilet water tank. The ball valve in the water inlet tube opens when the ball float is lower than the desired water level and closes tightly, preventing water from flowing into the tank when the ball reaches the top of the line of water. If the toilet has a ball valve and runs non-stop, that could be the float or ball valve. Both are easy to fix and can be replaced in a couple of hours.



KOHLER K-4304-L-0 Highline(R) Toilet with Pressure Lite(R) Flushing Technology and Bedpan Lugs, White White

Instructions

1 Close the water in the shut-off valve. Look for it connected to the water pipe behind and just to the left of the back of the toilet. If there is no valve in the toilet, or if you can not tighten with your fingers, turn off the water supply to the house until repairs are complete.

2 Pull the chain to ensure that the water is completely free. Water should not come out again in the reserve tank once emptied. If the water does not continue to flow into the tank, you should use a shut-off valve all the water in the house instead of the toilet water trigger to remove and put the shut-off valve on your list of things to replace in the future.

3 Remove the water line from the bottom of the toilet with a wrench or adjustable pliers. Remove the lid of the toilet tank by lifting it and set it aside.

4 Disconnect the nuts securing the ball valve and the water supply pipe to the tank using pliers. Check all the inner washers of the valves for cracking, tearing or other reasons to replace them.

5 Place the new ball valve with the existing or new washers, and place it through the bottom of the reservoir. Wrap the valve threads with the plumber's tape and attach it to the water pipe.

6 Replace and tighten all nuts to secure the ball valve and water line in place. Secure the ball float arm of the valve.

7 Open the water supply, either in the water shut-off valve behind the toilet, or in the water shut-off valve for the entire house. Check the water level to make sure the tank is filled properly. Adjust the float if the water levels are too high or too low. Put the lid on the tank.

Toto CST794EFRNo.01 Elongated Bowl and Tank with Right Hand Trip Lever 1.28-GPF, Nexus Collection, Cotton

How to replace a toilet and float valve

The float valve, also known as the valve or fill valve, is the accessory that fills your toilet after a flush. After the water leaves the tank, the float valve, normally in place by the water in the tank, decreases, allowing water to flow to it. When the float valve reaches a set height, the water flow to the fill valve is cut off. The replacement of a toilet or float valve involves draining the toilet so that it can reach the valve, remove it and replace it with a new one.



Toto CST794EFRNo.01 Elongated Bowl and Tank with Right Hand Trip Lever 1.28-GPF, Nexus Collection, Cotton

Instructions

1 Close the water for the toilet in which you will replace the toilet valve and float valve. This is usually behind the toilet on the wall. The supply shutoff valve will be round or oval. Turn this clockwise to close the water supply.

2 Pull the chain. Hold the handle down until all the water supply is gone. Wipe away any excess with a towel and sponge.

3 Disconnect the float valve lever from the fill valve. This could be held in place with a screw or snapped into place, depending on the model.

4 Disconnect the water supply valve from the inlet of the filling valve by unscrewing it. Unscrew the plastic retaining screw above the filling valve inlet. This keeps the fill valve in place in the bottom of the tank. Lift the fill valve and out of the tank.

5 Turn the new fill valve upside down. Apply a thin layer of grease to the bottom of the filler valve gasket. Turn the filling valve right side up. Insert into the tank so that the seal is flush with the bottom of the tank. Keep holding this in one place with your hand.

6 Reattach the retaining screw to the bottom of the tank by screwing it around the tank inlet. Tighten with the key.

7 Replace the float valve.

8 Wrap the inlet threads with plumber's tape. Replace the water inlet coupling.

9 Reset the water supply. Let the tank fill up. Rinse and check correct operation.

Tips and warnings

•     If possible, try replacing the fill valve that comes with an integrated float valve.

American Standard 3121.016.178 Champion Elongated Seatless Toilet Bowl, Black (Bowl Only)

How to repair a Cup float valve in a toilet

A float valve is a common type of toilets.The valve discharge valve consists of a tower in which a round plastic cup moves up and down. When the chain is pulled, the drop in the water level causes the cup to drop, letting the water flow into the tank. When the cup rises to the top, it will turn off the water. The main problem with the valves of the float cup is that the cup sticks, causing the water to run constantly. The repair of the float valve requires ensuring that the float cup moves smoothly in the tower.



American Standard 3121.016.178 Champion Elongated Seatless Toilet Bowl, Black (Bowl Only)

Instructions

1 Remove the lid of the toilet tank and put it out of the way.

2 Turn the shutoff valve on the floor next to the toilet all the way to the right to stop the water supply to the toilet. Pull the chain to remove most of the water in the tank.

3 Search for the float valve, which is on the left side of the toilet. Notice how the plastic cup is attached to the tower.

4 Apply plumber's grease with a cotton swab to the tower and the inside of the cup where the tower is inserted into it. Move the cup up and down the tower to work on the fat.

5 Turn on the shut-off valve for the water supply to the tank. Pull the chain several times to make sure the cup is working properly. Replace the tank lid.

STERLING 403315-0 Windham Toilet Bowl, White

How to adjust the float valve in a toilet

The float valve controls the water level in the toilet tank. As the water fills the reservoir, the float rises. When the float reaches a predetermined level, the water supply is interrupted. When your toilet is constantly running or you do not pull it completely, you need to adjust the float valve. The adjustment depends on whether you have a ball float or a float that rests on the fill valve.



STERLING 403315-0 Windham Toilet Bowl, White

Instructions

floating ball

1 Remove the tank lid from the toilet and place it on the ground out of your way. Locate the brass adjustment screw below the end of the ball float arm on top of the fill valve.

2 Turn the screw counterclockwise with a Phillips screwdriver to raise the water level if the bath is not emptying completely. Turn the 1/2-turn screw at the same time. Turn the screw clockwise with the screwdriver to lower the level if the toilet is running constantly.

3 Pull the chain and allow the toilet tank to fill. The water should be in the filling line on the back of the toilet cistern. They continue to make adjustments to the screw ball float as needed.

4 Place the toilet tank lid on the toilet once you have completed the adjustments.
Float-on-Fill valve

5 Take the lid of the toilet tank out of the toilet and place it on the floor out of your way.

6 Locate the level adjustment clip next to the float. The clip is a clip fastener that moves up and down a thin wire.

7 Squeeze the top and bottom of the clamp with your fingers. Lift the clip fastener and float to lower the water level, or lower them to increase the water level. Move the float and clip fastener in 1/2 inch increments.

8 Pull the chain and let the tank refill. There is a water line on the back of the toilet cistern. Continue making adjustments as necessary until the water level is in the water line on the back of the toilet tank.

9 Place the toilet tank lid on the toilet after all the settings are complete.

Tips and warnings

•     Do not bend the ball float arm to make adjustments. Bending the ball float arm could damage the connection at the top of the fill valve.

Duravit 22170900921 Toilet Bowl Wall-Mounted 14 5/8-Inch Vero

Problems with flush toilet valves

Bathrooms are a modern convenience when they are working properly, but they are a modern nuisance when they are not. A dump valve is a relatively simple mechanism, but when it starts to malfunction, it is difficult to repair, especially since many homeowners never look toward the back of their toilet until something goes wrong and they really do not know how the water works. toilet.



Duravit 22170900921 Toilet Bowl Wall-Mounted 14 5/8-Inch Vero

Partial closure

If the discharge valve closes only to a certain point, your toilet will probably continue to run and waste of water. Check that nothing is blocking the discharge valve and keep it open and that the toilet tank cover is not obstructing the movement of the discharge valve.

damaged joint

A damaged gasket or crack or hole in the tank below the discharge valve will lead to the same symptoms as a discharge valve that will not close: you will hear running water in the toilet when it should not. Inspect the discharge valve and the area around it for damage or something unusual, which could include cracking or discoloration of the porcelain, interference or obstruction by foreign objects or broken or bent mechanisms.

Bent ball tank

Tank balls were replaced with fins many years ago, but, if you have an old toilet, you can still have a tank ball, which is a plastic or metal sphere attached to a rod. The tank ball floats on the surface of the water in the toilet tank and lifts a lever that closes the discharge valve when the tank is full. If the rod to which the tank ball is attached is bent so that the tank ball is too low, the water stops before the tank is full. If the tank ball is too high, the water keeps running in the overflow tube because the mechanism has not told it to stop.

Flooded Fin

If you have a new toilet, your toilet has a flap valve instead of a tank ball. If you are having problems with the discharge valve, the fault lies most likely to be the trap. If the flap valve becomes saturated with water, it may fail to seal the outlet pipe and the water will continue to run outside the pipe, preventing it from shutting down. Replacing the flooded fin with a new one will solve this problem.