How to repair the electric clutch in an Ariens lawn mower

How to repair the electric clutch in an Ariens lawn mower

Ariens is a company that manufactures snow throwers and with walking driver, pushing lawn mowers. The company also manufactures a variety of riding lawn mowers. The cutting platform on the Ariens mower is controlled by the electric clutch. The clutch sends electric current from the battery to the cutting platform. Over time, the electrical clutch may become worn and spoiled. The cutting unit will not activate if the electrical clutch is outside. Replacing the electric clutch Ariens takes about an hour.

Lawn Mower Parts Product

Instructions

1 Ariens Clipper Park on a flat, level surface and then adjust the cutting platform to its highest level.

2 Open the Machine motor cover and remove the negative battery cable with an adjustable wrench.

3 Slide the jack under the mower, Jack upwards and the assembly connector is placed in place. Lower the Ariens in the making of grandstands.

4 Disconnect the plastic wire harness attached to the electrical clutch.

5 loosen the belt tension bolt and remove the drive belt from the pulleys.

6 Remove the bolt that attaches the electrical clutch to the crankshaft with the set of tubes. If lever is needed to remove the bolt, slide a swivel bar over the Ratchet key handle and then remove the bolt.

7 Raise the clutch age and retighten the new clutch in place. Screw in the setscrew and tighten with the set of tubes.

8 Adjust the back belt on the pulleys, slide the tensioner clockwise to increase the belt tension and tighten the tension bolt with the set of tubes.

9 Plug the electrical wiring harness into the new electrical clutch.

10 lift the Ariens, pull the grandstands and then lower the mower to the ground. Replace the negative battery cable.

How to light the headlights on a lawn mower Husqvarna YTH1542

How to light the headlights on a lawn mower Husqvarna YTH1542

Husqvarna YTH1542 Lawn Mower is an onboard driver, model tractor type. The lawn mower has a maximum speed of 5.5 miles per hour and forwards 2.4 MPH in reverse. The machine includes a front headlight that can be used to increase visibility for safety reasons, and provide forward lighting. The Headlight bulb is user-replaceable. Turning on the headlight in operation consists of a switch.

Lawn Mower Parts Product

Instructions

1 Identify the light switch ON the YTH1542 by sitting on the driver's seat and looking at the right side of the instrument panel behind the steering wheel. The order of the instruments from top to bottom is "clutch switch cover," Lights "and" stopwatch ".

2 Turn the light clockwise switch to turn on the headlights. Turn the switch to the left to turn it off.

3 Replace the bulb if the lights do not light. Lift the cover and pull the bulb holder out of the hole in the back of the grill. Replace the bulb in the bracket and push the lamp holder carefully back into the hole in the back of the grille. Near the bell.

How to repair the self-propelled belt in a Murray lawn mower

How to repair the self-propelled belt in a Murray lawn mower

When the drive belt on your Murray self-propelled mower begins to wear out, the drive system may start to fail, which can cause the drive belt to slide out of the drive pulley. When this happens, you must repair the drive belt that is used for the auto-propulsion function of the mower. You can repair the propel belt in a Murray lawn mower by removing the old transmission belt and installing a new one.

Lawn Mower Parts Product

Instructions

1 Locate the spark plug wire, and unplug it from the spark plug.

2 Remove the screw used to secure the mower strap cover with a screwdriver. Take the belt cover out of the mower.

3 loosen the belt tension bolt with the socket wrench. The belt tension Bolt is located next to the wheel adjustment lever on the front left side of the machine.

4 Pull the front of the drive belt out of the drive pulley located on the top of the motor.

5 Tilt the mower over the side, and pull the back of the drive belt over the mower blade.

6 Insert the back of the new drive belt over the mower blade, and place the front of the belt over the drive pulley.

7 Tighten belt tension bolt with socket wrench.

8 Locate the adjusting nut located on the bottom of the lawnmower near the belt tension bolt.

9 Tighten the nut with the wrench until it touches the spacer, and slightly loosen the nut so that the spacer can rotate.

10 Place the cover strap on the lawn mower and secure it with the screw.

11 Reconnect the spark plug wire to the spark plug.
Tips and warnings

    A new drive belt can be found in a tractor shop or directly from the manufacturer.
    If the spark plug wire is not disconnected, the mower could be accidentally started.

How to repair the front transmission in a 22-inch-6 HP GTS Toro recycler Lawn mower

How to repair the front transmission in a 22-inch-6 HP GTS Toro recycler Lawn mower

When you take the automatic unit on your bull mower 22-inch 6.5 HP GTS and does not move automatically forward, the belt slides too likely to participate properly. This means that the drive belt that runs the front wheels of the motor must be replaced. The process does not require the help of a certified Toro repairman. In fact, you can complete the repairs in your own backyard with a simple key or set.

Lawn Mower Parts Product

Instructions

1 unplug spark plug wire from spark plug to ensure no possibility of motor accidentally looking. It will work around the cutter blades which is vital to deactivate the engine.

2 Place the mower on the left side or so the black cover on the left wheel rests on the ground.

3 Remove the two 3/8 inch bolts that hold the cover in place with a wrench and then place the cap aside.

4 Remove the mower blade with a 5/8 inch wrench and then place the blade aside.

5 Remove the top screw that holds the strap guide in place with a 5/8-inch wrench. Loosen the lower screw that holds the guide in place with the same wrench and then move the belt guide away from the driver assembly.

6 Remove the belt from the pulley on the driver assembly and then pass through the cover toward the front of the mower.

7 Remove the strap from around the pulley on the front of the mower and then pull the strap out of the "fingers" on the mounting bracket with your fingers. Discard the old belt.

8 Place the strap between the "fingers" and then loop the strap around the pulley on the front of the mower. Pass the belt through the hole in the cutting platform.

9 Place the belt around the pulley under the mower and then turn the guard into position. Secure the protection by tightening the screws.

10 Place the cutting blade on the shaft and tighten with the correct screw.

11 Place the cover on the front of the machine and secure it with the two correct screws.

12 Reconnect the spark plug wire to the cutter.

End-of-season storage : lawn mower

End-of-season storage : lawn mower

To avoid starting problems next season, run the mower until it is cut for lack of fuel. This should remove most fuel from the carburetor and bowl and help prevent all gumming up. To prevent corrosion, allow the mower to cool, remove the spark plug and place a teaspoon of oil through the plug hole. Pull the starter cable a couple of times and replace the plug. Remove all the caked grass from the bottom of the shelf as it can ferment, acidify and eat through the metal over time.

Useful Links

Briggs and Stratton Oil recommendations

Locating engine model numbers, types and codes for outdoor power equipment in small Jack motors


If you can't start your lawnmower, maybe it's time to buy a new one. Consult my guide to choose and buy a lawn mower that analyzes the pros and cons of the electric, gas and battery models.

My personal experience with lawn mowers

I don't fix the turf equipment professionally, but I learned all this by playing with the engines since I was a teenager, and I have gained approximately thirty years of experience with lawn mowers, thread cutters and hedge trimmers.

Lawn Mower Parts Product

Routine lawn mower maintenance checks during the summer

Routine lawn mower maintenance checks during the summer

•     Check the oil every month or more regularly depending on usage.
•     Remove any grass or leaves from the cooling fins in the stock. Air blown through the flaps through the steering wheel drives the heat away from the engine so it is important that they are not clogged.
•     Sharpen the blade a few times during the season, again depending on use. If you have a small lawn, a single sharpening at the beginning of the year should suffice.
•     Check for loose nuts or screws on wheels or other parts of mower.
•     If possible, drip some light oil from the machine into the control cables for the throttle and the unit. If you do this little by little, it will slide along the wires on the cable sleeves, avoiding corrosion and grip.
•     Try to avoid mowing when wet. Wet grass clippings adhere to the bottom of the platform along with mud and other dirt. This clogs the way to the collection bag and eventually the engine may have difficulty during cutting. After use in these conditions, wash the bottom of the platform with a hose, but try not to put water in the motor and air filter.

Lawn Mower Parts Product

Do not attempt to start an engine without the blade! : lawn mower

Do not attempt to start an engine without the blade! : lawn mower

Small motors, such as lawn mowers, usually have an aluminum flywheel, and the additional weight of the blade is actually part of the steering wheel system. If you are familiar with the mechanics (a branch of physics), you will know that this increases the moment of inertia of the system. If the blade is removed, it will be difficult to start the engine due to insufficient turn impulse when pulling on the starter cable.

Lawn Mower Parts Product

Throttle and Governor links : lawn mower

Throttle and Governor links : lawn mower

    Verify that the throttle cable is actuating the accelerator plate through the links. These can sometimes be caught or obstructed by small grass or twigs.
    Make sure the governor's linkage does not keep the throttle closed. A governor is a device that regulates the speed of an engine, keeping it constant regardless of the load on the engine. On a lawn mower, two types of governor are used. A system consists of a paddle pivoted at one end and connected to the accelerator plate in the carburetor through a spring and joints. The air is directed from the flaps of the steering wheel to the fin. If the motor slows down (due to long grass), this reduces the air force on the paddle. This allows a spring to open more the throttle, allowing more fuel in the engine, which gives it more power and this increases the speed to compensate. The governor also limits the engine's excess acceleration by closing the throttle when the load is reduced. Another type of governor works by centrifugal force. A spool that can slide on a shaft acts on arms that move more outward as the engine speed increases. The Reel powers the accelerator through links.

    With the air filter removed and the use of a torch, you can determine the position of the choke and choke valves. These are dishes that open or close at the entrance. The outermost plate is the choke that almost completely obstructs the airway when it is turned on during a cold start of the engine. The accelerator plate creates the slightest obstruction with the throttle thoroughly and the regulator binding should not be closed before the engine starts. Verify that the governor can move freely and does not stick.

Lawn Mower Parts Product

Smoke is a symptom of a tale : lawn mower

Smoke is a symptom of a tale : lawn mower

The color of the exhaust smoke is a symptom that reveals problems with an engine.

White or blue smoke?

This is caused by the burnt oil in the engine. While a certain amount of oil is consumed and burned under normal circumstances, blue smoke clouds indicate a problem. Old engines emit smoke as the cylinder wears out (motor burnout) and the piston and rings no longer fit as well. Excess oil is added to the cylinder and burned. Fractured piston rings can allow a large amount of oil to enter the cylinder.

The oil in combustion can also be caused by a defective vent that allows the oil to be expelled from the sump and then sucked into the engine through the carburetor (if there is a pipe connecting the vent to the carburetor).

However, another cause is an overloaded sump. On one occasion, my neighbor and his helpful friend decided to fill the lawnmower with oil and, being generous, decided to fill the oil to the edge of the oil filler cap. The result? Thick clouds of white smoke I could see in the distance! Yours really had to save the day and drain some oil from the pruner!

Black smoke?

Black smoke is an indicator of burning too much gas. This can be caused by too rich a mixture (adjust the mixer screw), a defective diaphragm or punctured in the carburetor, a choke that does not open when the engine starts or a dirty air filter.

Lawn Mower Parts Product

Engine compression : lawn mower

Engine compression : lawn mower

While fuel and a good spark are essential for starting an engine, good compression is also important. Compression is simply the capacity of the fuel/air vapor to be compressed by the piston into the cylinder (also known as the combustion chamber) before the ignition, without spilling out somewhere due to a bad seal.

Lawn Mower Parts Product

You can get a rough idea of compression by placing your thumb over the hole where the screw is threaded and pulling the starter cable or turning the handwheel if it is easier. You should be able to feel the pressure on your thumb. However, with the spark plug back in place, if the compression is severely compromised, the starter cable will be easy to pull, no resistance.

Bad compression can have several causes:

•     Spark Plug loose. It could be as simple as a loose spark plug, so tighten it. Do not use excessive force when tightening.
•     Defective cylinder Head gasket. The cylinder head is the part of the motor on which the plug is mounted. This is screwed into the cylinder block with the gasket inserted. You may notice burns or soot marks around the edges of the gasket.
•     Bore Wear. Another cause of bad compression is the wear of the orifice, which causes the piston to seal badly in the cylinder. This can happen when an engine reaches old age, or if it has been used without air filter or with little oil.
•     Clogged Open valves: Fire and spit. Another cause of poor compression is an open or poorly seated valve. During the 4-stroke cycle, an inlet valve is opened and allows the air/gas mixture to flow into the cylinder, and an exhaust valve opens to allow the burned gases to be ejected from the cylinder. During the compression stroke, both valves must be closed. Now, if valves do not settle and seal completely due to wear, the accumulation of deposits or the exhaust valve burned during many years of use of the engine, the compression can suffer. Another scenario is if an engine to one of the valves open. If the motor is stored for years without use, what can happen is clogging the valve in this position. Now, normally, a cam shaft opens each valve through rods in contact with the pushers called stems, and a spring returns the valve to the closed position. If the valve becomes clogged, the spring force is not strong enough to return the valve to the closed position. The symptoms of a stuck or worn valve may spit or shoot through the carburetor or the escape while the engine starts or that the Starter cable is actually easy to pull. So the moral of the story is "exercise" machines in storage periodically to prevent this from happening. This can be as simple as gently pull cable starting motor so all move internally. This applies to anything with moving parts, including engines, motors, tools and workshop equipment.

In fact, I experienced a compression problem with my lawn mower this morning, although it's not too old. The cable was easy to pull without resistance so I guess it jammed a valve. After leaving the engine for about an hour, the problem was solved, perhaps because the oil penetrated the lifters or valve stems.

When looking inside the cylinder through the spark plug hole or removing an inspection cap over a compartment (known as a valve hood) that provides access to the pushers, you can see if a valve is opening. Some engines have OHV or higher valves, and can be accessed again by removing an access cover. The valves can be released by spraying WD40 on the valve seat and on the stems. However, this may be beyond the ability of the hobbyist. If it is necessary to remove the cylinder head, when replacing it, the screws must be tightened in a staggered sequence and the bolts should ideally be re-tightened with a torque wrench.

The spit can also be caused by a mixture that fits too thin, which requires the mixing screw to turn to the left to enrich it (see above procedure). Another cause of spitting is a cut-off key, causing the timing to be off and the spark plug to trip at the wrong time.

FUEL PUMPS, Low oil level : lawn mower

FUEL PUMPS, Low oil level : lawn mower

FUEL PUMPS

Small motors use a simple gravity feed system to fill the floating container. Larger engines, such as lawn tractors, require a higher flow of gas. In addition, the gas tank may be located lower than the carburetor. Then a fuel pump may be required. These pumps may be electric, use a camshaft rod to operate a diaphragm in the pump or rely on the carburetor suction through a diaphragm-operated hose (a diaphragm is a flexible material drive pushed back and towards Ade Lante to fuel pump.

Typical faults in pumps are a loss of voltage in the pump, a clogged filter in the pump, a disconnected air hose, a perforated diaphragm, or the pump component intake.

Low oil level

Larger engines with an electrical system sometimes have a low-oil floating switch. This prevents the engine from starting and being damaged if the oil in the sump is below a threshold level.

Lawn Mower Parts Product