How to repair a Scotts lawn mower

How to repair a Scotts lawn mower

A Scotts lawn mower is a reel type slitter that does not have an electric or petrol engine. Instead, the mower has five spiral-shaped blades that rotate against a cutting bar, driven by the forward movement of the large front wheels of the mower. Since there is no escape from the engine to contribute to any pollution problem, coil cutters are ideal for environmentally-conscious gardeners. If your clipper will need any change, you can repair a Scotts lawn mower with some common hand tools.

Lawn Mower Parts Product

Instructions

1 Place the mower on a work table and remove the handle assembly.

2 Turn the mower on the left side. Slide a flat-blade screwdriver into the C-clip in the center of the drive wheel on the right side and pry it out of the shaft. Take off the wheel and set aside.

3 Check the condition of the drive sprocket on the spindle. If you see damage, replace with a new transmission gear. Replace the drive wheel and C-clip.

4 Position the cutter so that the two wheels are on the table. Push the mower forward, and see how the spiral blades turn against the cutting bar. The blades should slide smoothly without gaps between the blades and the bar. If gaps appear, adjust the screw on each side of the cutting bar until both sides slide the blades against the bar evenly.

5 Push the mower forward again, and insert a paper strip over the beaters. The blades must be cut cleanly from the newspaper. If the paper does not cut cleanly, you may have to repeat the settings in the previous step.

6 Put the handle back on the lawnmower, and place the machine on the ground. Lawn mower test. The mower should be cut evenly and smoothly.

How to repair a starter cable in a Weed Eater lawn mower 22 inches

How to repair a starter cable in a Weed Eater lawn mower 22 inches

The starter rope in a Weed Eater lawn mower 22 inches runs through a spring pulley and kick system. The pulley is located on the steering wheel and when the rope is pulled, the pulley and the steering wheel rotate together. When the rope is released, the return spring engages and pulls the rope back into the pulley. This rope can get frayed, worn or torn from too much traction. The pulley and recoil spring may also lose its effectiveness and need to be replaced.

Lawn Mower Parts Product

Instructions

1 unscrew the cover of the starter box. On some models, you may need to remove the fuel tank for access to the screws on the boot box cover. Unscrew the fuel tank and remove the cover from the starter box. Unscrew the bolt securing the rope guide and rope to one side of the lawn mower handle.

2 switch on the starter covers more than access the starter rope pulley. Keep your thumb on the pulley. Cut the old wire at the base of the handle and into the knot in the pulley. Let the tension out in the recoil spring slowly, raising the thumb a little at a time. Take the old wire from the pulley.

3 Loosen the pulley on the cover of the starter box. Slide the screw, washer and pulley. Remove the return spring from inside the center of the pulley. Inspect the pulley and return spring for damage and replace if they break.

4 Pass the new length of the starter rope through the hole inside the pulley. Tie a knot in the base of the rope and pull the rope all the way through the hole. Wind the wrist-needle rope around the pulley. Push the return spring back into the center of the pulley. Lubricate the starter post with the grease of the motor. Set pulley, washer and screw, tighten starter post screw.

5 Jiggle the pulley back and forth until it is coupled with the return spring. Pass the rope through the hole in the starter cap. Pass the rope through the starter handle and tie another knot in the top of the handle. Make sure the starter rope pulls out and recoils again.

6 fit the starter-box cover back into the motor. Tighten all screws. Replace the fuel tank if necessary. Route the starter rope to the mower handle and replace the rope guide, tighten the screw with the wrench.

How to repair the starter rope in a lawn mower

How to repair the starter rope in a lawn mower

Each time you pull start your mower, the nylon braided wire is rubbed against the round and smooth splint on the side of the starter coil. This constant friction makes the rope wear out and finally break. Since it only takes a few minutes to adapt to a new cable, removing the recoil starter and winding a new rope around the pulley at the first sign of wear, it is easier to replace a frayed rope than to excavate the jammed debris from the pulley des Then the rope fits.

Lawn Mower Parts Product

Instructions

1 Loosen the three or four 1/4-inch bolts that hold the starter coil to the motor with a socket wrench, and place the unit in inverted position on your workbench.

2 cut the cable just below the starter handle with a pair of side cutters and unwind the wire around the pulley. Grasp the knot protruding from the pulley flange with a pair of pliers, and pull the worn rope out of the starter motor.

3 Feed a new rope through the starter handle. Tie an eight knot around the end of the cable protruding through the back of the handle and cut the rope about an inch from the knot. Hold the handle with one hand and give the rope a couple of pulls to tighten the knot.

4 Relax the pulley around half a turn counterclockwise against the return spring tension until the flange hole in the pulley lines aligns with the ferrule on the side of the casing. Keep the pulley with your thumb and feed the new cable through the splint and up through the hole in the pulley flange.

5 Tie a single knot on the end of the cable. Pull the protruding rope out of the splint, and give it a couple of pulls to tighten the simple knot on the pulley. The ease of the rope to allow the pulley, to close the clock needles again around half a turn until it stops.

6 cut the cord about 3/8 inches from the knot and seal the end by melting with a lighter or phosphorus to prevent frayinging.

7 Hook a folded paper clip around the rope between the splint and the pulley. Pull the rope up to form a loop between the pulley and the inside edge of the casing, until the handle rests on the side of the casing. Rest the pulley a bit to align the notch on the upper outer edge of the pulley, about an inch before the splint arrives.

8 Insert the end of the rope pulley into the notch on the edge of the pulley at the bottom. Roll the two-turn pulley anti-clockwise against the return spring tension until the rope engaged in the notch is just after the splint. Pull the starter handle to release the rope from the notch; Relieve the tension on the rope to allow the pulley to relax and draw the handle to the side of the casing.

9 Check that the rope has removed the starter handle all the way to the side of the back casing; If there is still some slack, repeat the previous step and the tension of the pulley to the left again, before pulling the free rope from the notch on the side of the pulley; This should point the handle to the bottom against the side of the casing.

10 Attach the starter coil to the motor with the screws removed above, and the test to start the mower to complete the installation.

How to repair the electric clutch in an Ariens lawn mower

How to repair the electric clutch in an Ariens lawn mower

Ariens is a company that manufactures snow throwers and with walking driver, pushing lawn mowers. The company also manufactures a variety of riding lawn mowers. The cutting platform on the Ariens mower is controlled by the electric clutch. The clutch sends electric current from the battery to the cutting platform. Over time, the electrical clutch may become worn and spoiled. The cutting unit will not activate if the electrical clutch is outside. Replacing the electric clutch Ariens takes about an hour.

Lawn Mower Parts Product

Instructions

1 Ariens Clipper Park on a flat, level surface and then adjust the cutting platform to its highest level.

2 Open the Machine motor cover and remove the negative battery cable with an adjustable wrench.

3 Slide the jack under the mower, Jack upwards and the assembly connector is placed in place. Lower the Ariens in the making of grandstands.

4 Disconnect the plastic wire harness attached to the electrical clutch.

5 loosen the belt tension bolt and remove the drive belt from the pulleys.

6 Remove the bolt that attaches the electrical clutch to the crankshaft with the set of tubes. If lever is needed to remove the bolt, slide a swivel bar over the Ratchet key handle and then remove the bolt.

7 Raise the clutch age and retighten the new clutch in place. Screw in the setscrew and tighten with the set of tubes.

8 Adjust the back belt on the pulleys, slide the tensioner clockwise to increase the belt tension and tighten the tension bolt with the set of tubes.

9 Plug the electrical wiring harness into the new electrical clutch.

10 lift the Ariens, pull the grandstands and then lower the mower to the ground. Replace the negative battery cable.

How to light the headlights on a lawn mower Husqvarna YTH1542

How to light the headlights on a lawn mower Husqvarna YTH1542

Husqvarna YTH1542 Lawn Mower is an onboard driver, model tractor type. The lawn mower has a maximum speed of 5.5 miles per hour and forwards 2.4 MPH in reverse. The machine includes a front headlight that can be used to increase visibility for safety reasons, and provide forward lighting. The Headlight bulb is user-replaceable. Turning on the headlight in operation consists of a switch.

Lawn Mower Parts Product

Instructions

1 Identify the light switch ON the YTH1542 by sitting on the driver's seat and looking at the right side of the instrument panel behind the steering wheel. The order of the instruments from top to bottom is "clutch switch cover," Lights "and" stopwatch ".

2 Turn the light clockwise switch to turn on the headlights. Turn the switch to the left to turn it off.

3 Replace the bulb if the lights do not light. Lift the cover and pull the bulb holder out of the hole in the back of the grill. Replace the bulb in the bracket and push the lamp holder carefully back into the hole in the back of the grille. Near the bell.

How to repair the self-propelled belt in a Murray lawn mower

How to repair the self-propelled belt in a Murray lawn mower

When the drive belt on your Murray self-propelled mower begins to wear out, the drive system may start to fail, which can cause the drive belt to slide out of the drive pulley. When this happens, you must repair the drive belt that is used for the auto-propulsion function of the mower. You can repair the propel belt in a Murray lawn mower by removing the old transmission belt and installing a new one.

Lawn Mower Parts Product

Instructions

1 Locate the spark plug wire, and unplug it from the spark plug.

2 Remove the screw used to secure the mower strap cover with a screwdriver. Take the belt cover out of the mower.

3 loosen the belt tension bolt with the socket wrench. The belt tension Bolt is located next to the wheel adjustment lever on the front left side of the machine.

4 Pull the front of the drive belt out of the drive pulley located on the top of the motor.

5 Tilt the mower over the side, and pull the back of the drive belt over the mower blade.

6 Insert the back of the new drive belt over the mower blade, and place the front of the belt over the drive pulley.

7 Tighten belt tension bolt with socket wrench.

8 Locate the adjusting nut located on the bottom of the lawnmower near the belt tension bolt.

9 Tighten the nut with the wrench until it touches the spacer, and slightly loosen the nut so that the spacer can rotate.

10 Place the cover strap on the lawn mower and secure it with the screw.

11 Reconnect the spark plug wire to the spark plug.
Tips and warnings

    A new drive belt can be found in a tractor shop or directly from the manufacturer.
    If the spark plug wire is not disconnected, the mower could be accidentally started.

How to repair the front transmission in a 22-inch-6 HP GTS Toro recycler Lawn mower

How to repair the front transmission in a 22-inch-6 HP GTS Toro recycler Lawn mower

When you take the automatic unit on your bull mower 22-inch 6.5 HP GTS and does not move automatically forward, the belt slides too likely to participate properly. This means that the drive belt that runs the front wheels of the motor must be replaced. The process does not require the help of a certified Toro repairman. In fact, you can complete the repairs in your own backyard with a simple key or set.

Lawn Mower Parts Product

Instructions

1 unplug spark plug wire from spark plug to ensure no possibility of motor accidentally looking. It will work around the cutter blades which is vital to deactivate the engine.

2 Place the mower on the left side or so the black cover on the left wheel rests on the ground.

3 Remove the two 3/8 inch bolts that hold the cover in place with a wrench and then place the cap aside.

4 Remove the mower blade with a 5/8 inch wrench and then place the blade aside.

5 Remove the top screw that holds the strap guide in place with a 5/8-inch wrench. Loosen the lower screw that holds the guide in place with the same wrench and then move the belt guide away from the driver assembly.

6 Remove the belt from the pulley on the driver assembly and then pass through the cover toward the front of the mower.

7 Remove the strap from around the pulley on the front of the mower and then pull the strap out of the "fingers" on the mounting bracket with your fingers. Discard the old belt.

8 Place the strap between the "fingers" and then loop the strap around the pulley on the front of the mower. Pass the belt through the hole in the cutting platform.

9 Place the belt around the pulley under the mower and then turn the guard into position. Secure the protection by tightening the screws.

10 Place the cutting blade on the shaft and tighten with the correct screw.

11 Place the cover on the front of the machine and secure it with the two correct screws.

12 Reconnect the spark plug wire to the cutter.

End-of-season storage : lawn mower

End-of-season storage : lawn mower

To avoid starting problems next season, run the mower until it is cut for lack of fuel. This should remove most fuel from the carburetor and bowl and help prevent all gumming up. To prevent corrosion, allow the mower to cool, remove the spark plug and place a teaspoon of oil through the plug hole. Pull the starter cable a couple of times and replace the plug. Remove all the caked grass from the bottom of the shelf as it can ferment, acidify and eat through the metal over time.

Useful Links

Briggs and Stratton Oil recommendations

Locating engine model numbers, types and codes for outdoor power equipment in small Jack motors


If you can't start your lawnmower, maybe it's time to buy a new one. Consult my guide to choose and buy a lawn mower that analyzes the pros and cons of the electric, gas and battery models.

My personal experience with lawn mowers

I don't fix the turf equipment professionally, but I learned all this by playing with the engines since I was a teenager, and I have gained approximately thirty years of experience with lawn mowers, thread cutters and hedge trimmers.

Lawn Mower Parts Product

Routine lawn mower maintenance checks during the summer

Routine lawn mower maintenance checks during the summer

•     Check the oil every month or more regularly depending on usage.
•     Remove any grass or leaves from the cooling fins in the stock. Air blown through the flaps through the steering wheel drives the heat away from the engine so it is important that they are not clogged.
•     Sharpen the blade a few times during the season, again depending on use. If you have a small lawn, a single sharpening at the beginning of the year should suffice.
•     Check for loose nuts or screws on wheels or other parts of mower.
•     If possible, drip some light oil from the machine into the control cables for the throttle and the unit. If you do this little by little, it will slide along the wires on the cable sleeves, avoiding corrosion and grip.
•     Try to avoid mowing when wet. Wet grass clippings adhere to the bottom of the platform along with mud and other dirt. This clogs the way to the collection bag and eventually the engine may have difficulty during cutting. After use in these conditions, wash the bottom of the platform with a hose, but try not to put water in the motor and air filter.

Lawn Mower Parts Product

Do not attempt to start an engine without the blade! : lawn mower

Do not attempt to start an engine without the blade! : lawn mower

Small motors, such as lawn mowers, usually have an aluminum flywheel, and the additional weight of the blade is actually part of the steering wheel system. If you are familiar with the mechanics (a branch of physics), you will know that this increases the moment of inertia of the system. If the blade is removed, it will be difficult to start the engine due to insufficient turn impulse when pulling on the starter cable.

Lawn Mower Parts Product

Throttle and Governor links : lawn mower

Throttle and Governor links : lawn mower

    Verify that the throttle cable is actuating the accelerator plate through the links. These can sometimes be caught or obstructed by small grass or twigs.
    Make sure the governor's linkage does not keep the throttle closed. A governor is a device that regulates the speed of an engine, keeping it constant regardless of the load on the engine. On a lawn mower, two types of governor are used. A system consists of a paddle pivoted at one end and connected to the accelerator plate in the carburetor through a spring and joints. The air is directed from the flaps of the steering wheel to the fin. If the motor slows down (due to long grass), this reduces the air force on the paddle. This allows a spring to open more the throttle, allowing more fuel in the engine, which gives it more power and this increases the speed to compensate. The governor also limits the engine's excess acceleration by closing the throttle when the load is reduced. Another type of governor works by centrifugal force. A spool that can slide on a shaft acts on arms that move more outward as the engine speed increases. The Reel powers the accelerator through links.

    With the air filter removed and the use of a torch, you can determine the position of the choke and choke valves. These are dishes that open or close at the entrance. The outermost plate is the choke that almost completely obstructs the airway when it is turned on during a cold start of the engine. The accelerator plate creates the slightest obstruction with the throttle thoroughly and the regulator binding should not be closed before the engine starts. Verify that the governor can move freely and does not stick.

Lawn Mower Parts Product