How to install a toilet?

How to install a toilet?

Changing sanitary devices or placing a new ceramic can radically transform not only the appearance of the bathroom, but also the lifestyle of the one who uses it. So if your toilet is already worn, stained or broken, changing it can be an easy task to improve your environment.

Toilet Bowl Ring Remove Product

Tools to use:

• Bucket
• Concrete Drill
• Drill bit for ceramics
• Cross screwdriver
• Paddle tip Screwdriver
• Tape measure
• French key
• Pelican Key
• Caulking gun (for silicone)
• Electric drill

Materials to be used:

• Non-stick resin tape
• Silicone with fungicide
• Toilet
• WD40

 Before you start

Before removing the toilet, measure the distance between the back wall and the side screws at the base of the fixture, this will give you the measurement of the drain shaft on the floor.
With this measure choose your new device, selecting one that has the same axis or slightly larger.
Check all parts of your new toilet.

Parts List:

•     Cup and Pond
•     Anchor screws to Floor
•     Full Tank valve
•     Tank-to-cup coupling seal
•     Pond fixing bolts to cup
•     Discharge handle
•     Flexible Water
•     Wax drain ring with plastic, integral verse
•     Seat
•     Stopcock (optional)

1

Remove the existing toilet.

•     Drain the pond.
•     Close the Stopcock (also known as the angular key) so that it does not pass
•     More water.
•     If there is no stopcock for the pond, or else you want to change it, close the key
•     General step of the house and open some water faucets in other rooms
•     To drain the whole system.

•     Remove the toilet chain so that the water flows into the bowl. Should not enter
•     More water to the pond.
•     Put a bucket to receive the water and unscrew the existing flexible key
•     By the way.

•     Remove the anchor bolts from the cup.
•     Remove the pond from the Cup. This is not essential but it makes it easier to move.
•     If the nut is rusty and very tight, apply WD40 or similar product
•     to release it.

Recommendation

The toilets are heavy, take care of your back when lifting and moving.
DrainAlways try to use the same existing drain on the floor; Changing the position is complicated and quite demoro, and if the house has a single bathroom, it can become a real problem.
A change of drain implies-normally-more than a couple of working days: to break radieres or slabs, to cut existing pipes, to put a new section of pipe, to empty concrete again to close, etc.
And for all this it is advisable to hire specialists.

2

Install the new Cup

•     Present the cup with your pond and mark on the floor the location of the perforations for the new bolts.
•     If the location coincides with the above, remove the old anchors and put some new ones. Now, bolt the new.
•     If the perforations do not coincide, these holes must be filled with cement.
•     Once dry, drill two new holes with a ceramic bit.
•     Insert new plastic anchors.

Cup Position To ensure that the outlet hole in the bowl is perfectly centered on the drain pipe, do the following:

1. Once the old Cup is removed, mark the shafts of the drain pipe on the floor.
2. Put the new Cup back down and mark on its base the axles, extend
On the side faces.
3. Place the new cup by matching the marked shafts with the floor strokes.
4. Mark the contour of the workpiece on the floor and remove it.

3

Fit the wax ring

•     Put the cup, without the pond, legs up (inverted) and carefully resting on a carton so that it is not scratched.
•     Remove the protective cover from the wax ring.
•     Fit firmly into the bowl drain.

To level
Sometimes the ceramics on the floor are not well leveled.
If this happens, put plenty of silicone on the edge of the toilet base. This will help you level the position once it is set.

4

Seat Cup

   

•     Turn the cup carefully and lower it until the wax ring is perfectly aligned with the floor drain.
•     Press firmly into position.

   

•     Clean the silicone that comes out when you push the cup against the floor.

   

•     Screw the fixing bolts with their respective seals.

Installing pond Parts The inlet valve is installed with the separate 13 MMS float from the rear pond wall. The discharge valve is installed facing the discharge pipe.

5

Insert the inlet valve

•     Screw the float to the metal bar.
•     Insert the bar in the upper part of the valve and tighten in position by screwing.
•     Insert the valve into the corresponding hole in the pond, making sure it has the seal in place.
•     Notice that the float is separated from the walls of the pond.
•     With a pelican wrench secure the locking nut. Do not overtighten the account.

6

Insert the discharge valve

•     Insert the discharge valve into the central hole of the pond and with the locking nut secure it at the bottom.
•     The vertical overflow pipe must be oriented towards the inlet valve.
•     The top edge of the overflow pipe must be at least 13 MMS below the level of the handle perforation.

Recommendation

Be careful not to obstruct the placement of the two coupling bolts or the float bar.

7

Place coupling Seal

•     Place the coupling seal on the threaded end of the discharge valve, taking care to leave the tapered side down and the two bolt holes aligned.

8

Settling the pond

•     Install the pond on the bowl and match the coupling holes.

9

Connect the pond

•     Place the flat rubber washers to the bolts.
•     Insert them into the holes in the pond by placing the metal washers and nuts on the bottom.
•     Tighten the nut by hand, then hold it in place with a French spanner and tighten it from the top with a screwdriver.

10

Install the plug

•     Remove the protection from the underside of the flapper or stopper.
•     Connect in the indicated location to the discharge valve and the ears to the overflow pipe.

11

Install the discharge handle

•     Insert the discharge lever through the hole in the tank for the handle.
•     Secure with locking nut, turning counterclockwise.
•     The handle must be horizontal.
•     Connect the knurled banner of the plug to the discharge lever.
•     Adjust the length so that it rests completely on the discharge valve.

12

Insert the filling Hose

•     Insert the filling hose into the overflow tube.

13

Connect the Flexible

   

•     Connect the stopcock to the thread of the inlet key with a flexible toilet water supply.
•     Tighten with a French key without exaggeration.
•     Roll some non-stick resin tape into the thread of the nut or stopcock.

   

•     Open the stopcock.
•     The water level in the pond must be lower than the level of the overflow tube.
•     Regular with the screw at the top of the inlet valve, this will force the float to go down in the water.

14

Seal Cup

 Seal with silicone around the bottom edge of the bowl and floor.

How to remove scale from the bathroom with Coca Cola

How to remove scale from the bathroom with Coca Cola

The next time you stop for a Coke, make sure you have one for the house too. There are many things this soda can clean up in the house.

Toilet Bowl Ring Remove Product

Use Coca Cola as a bath cleaner

    6 ways you can clean with Coca Cola

•     What is good for removing stains from the toilet?
•     How to clean the bathroom with baking soda?
•     Tips on how to clean your bathroom effectively
•     How to clean your bathroom
•     How to unclog the toilet?
•     How to uncover a toilet without calling a plumber?
•     How to clean the toilet in the bathroom?
•     How to clean the bathroom in 10 minutes or less?
•     11 Amazing easy tips to clean your bathroom
•     Tips to clean your bathroom
•     Clean your bathroom with a product that is in the pantry of your kitchen
•     Tips for properly cleaning the bathroom

Some of them may even surprise you. Keep reading to find out exactly what you can clean a carbonated beverage.

Clean the 3 main articles of the Bath: the bath, the basin and the toilet.

Do you have hard water spots or ring around the toilet? Use Coca Cola and the toilet brush to remove the ring and allow the soda to rest for a while. Rinse when finished and have a toilet as good as new.

Desatascos madrid

For the sink and the bathtub, the Coca Cola breaks the layer and leaves them shiny. Pour directly over the area and wipe with a rag. It also helps to unclog your hair and dirt in your pipes as you go down.

Use in Greasy items:

Your husband has worked in the car all day and now his clothes are a greasy mess? What about that dish that the ham baked all day, now more greasy than your clothes? Use Coca Cola and allow items to rest, either in the washer or kitchen sink. The acid in a soda breaks the fat from the items and does not stain the clothes you are wearing.

You can also use Coca Cola in your vehicle. If the wiper fluid is not doing the work, stop and buy a Coke. Pour directly on the windshield and it will be in perfect condition.

Coca Cola is also a great way to remove all rust and corrosion from battery cables. Simply pour, let stand and observe how corrosion disappears, thanks to the acid of this wonderful beverage.

Use Coca Cola to clean

One of the active ingredients of Coca cola is phosphoric acid. It has a pH of 2.8, (on a scale of 1 -14, being 1 the most acid, 7 neutral and 14 very caustic). Pure phosphoric acid can eat through the metal and dissolve the concrete, but it certainly makes this drink taste good.

Rumors say Coca Cola distributors have used it over the years to clean the engines of their delivery trucks, and it also works to help remove dirt from the pavement of your windshield.

How to install two wax rings in a toilet

How to install two wax rings in a toilet

A leak in a toilet can be caused by things like a crack in the porcelain, a poor seal between the tank or a damaged inlet nozzle. If the toilet drips from under the base, the problem could be with the seal between the waste horn and the floor, which is sealed by a wax ring. In some installations where the toilet flange is lifted from the floor or the toilet waste horn design is unusually high, installing two wax rings can provide a more airtight seal, avoiding leaks under the toilet.

Toilet Bowl Ring Remove Product

• 1 Close the water supply valve behind the toilet. Unload the toilet to remove as much water as possible. Lift the lid off the back of the tank and remove all remaining water from the tank and toilet with a sponge.
• 2 Loosen the coupler that connects the supply line to the teat on the underside of the toilet tank using sliding joint pliers. Disconnect the supply line.
• 3 Remove the screw covers from the toilet base with a screwdriver. Place caps aside. Loosen the nuts on the mounting bolts using an adjustable wrench. Remove Washers. Lift the toilet bowl off the floor and place it sideways.
• 4 Scrape the old wax ring from the flange and the bottom of the waste horn into the base of the toilet using a spatula. Remove old bolts from floor flange cabinet. Insert a new set of cabinet bolts into the flange.
• 5 Place a wax ring over the floor flange. Align a second ring on the first and press down gently to begin molding The two wax rings together so that they do not get undone by placing the toilet in place.
• 6 Center The speaker on the toilet base over the wax rings and align the cabinet bolts with the mounting holes in the toilet base. Press the toilet, rocking the base slightly to seat the bowl against the rings.
• 7 Lift the toilet seat and place a level on the bowl. Slide a toilet wedge under the lower edges of the toilet base until the toilet is level in all directions. Place a washer over each cabinet bolt and tighten the nuts to the cabinet bolts with an adjustable wrench to secure the toilet. Replace Bolt caps.
• 8 Apply a drop of silicone putty around the base of the toilet to seal the floor base.
• 9 Connect the supply line coupler to the power nozzle on the bottom of the tank using the slide joint pliers. Open the water supply valve and test the toilet, observing leaks around the base.

Things you'll need

• Large sponge
• Sliding joint pliers
• Screwdriver Adjustable wrench
• Spatula Locker bolts with washers and nuts
• Two Wax bath rings
• Level
• Toilet wedges
• Silicone
• Putty

Tip

• A toilet is heavy, so you may want a wizard to help you place the bowl on the flange.

How to Change a Toilet Step by Step

How to Change a Toilet Step by Step

A noisy, leaky plumbing is not something you have to live with. Any owner with basic skills and tools can change a toilet and upgrade it to a new water-saving design.

Toilet Bowl Ring Remove Product

Installing a new toilet will take a couple of hours, but the reward will last for years.
Tools and Materials

•     Spatula
•     Adjustable wrench
•     Screwdriver
•     Spare toilet
•     Wax Ring
•     Toilet bolts
•     Silicone Caulking Putty

How to take steps for a new toilet

Make sure the new toilet is fitted to the previous place.

Measure from the wall behind the toilet to the center of one of the adjustment bolts (the bolts that hold the toilet to the floor). Do this before you take out the old toilet so you can buy a new one and have it handy before you start. If the toilet has four adjustment bolts, measure to the center of one of the back.

Also, measure from the center of the mounting holes to the back of the new toilet you have chosen. Compare these two measurements. If the base of the new toilet is shorter than the distance between the holes for the rear bolts and the wall, it should fit.

In small bathrooms where space is small, also measure from the sides of the flanged bolts to the side walls or other objects to make sure there is space between the sides. You don't want to find out after you start that you can't put the new toilet in place because you're trying to occupy part of the same space as your sink.
How to buy the toilet

Unless you buy one of the slim new models in one piece, you will have to buy the cup and tank. They'll come in two separate boxes. Virtually any tank you buy will have the discharge valve assembly installed, but it would not be too much to check.

In addition, you will need new adjustment bolts, a wax gasket and a toilet seat if they are not included. If you think about replacing the supply line, those that are flexible are coated in stainless steel mesh and are resistant, attractive and very practical. There are also cheaper plastic supply lines, in case you are worried about the price.
How to remove the old toilet

If you want to remove a toilet to change it, it will be better for your back, your floor and your walls if you retire it in pieces. Even if you remove the toilet, do not break it.

•     Cut off the toilet water supply. There must be a valve next to the tank that extends from the base of the wall or floor.
•     Pull the toilet chain and remove any remaining water from the tank, and from the bowl with a small cup and sponge.
•     If you plan to reuse the supply line, unplug it from the bowl. If you plan to replace the supply line, remove it from the supply valve and just leave it attached to the cup.
•     Remove the lid from the tank and place it on the floor, far away so that it does not interrupt, or better, in another room. Do not support this fragile piece against the wall near your workplace. If you fall or hit while trying to move heavy parts of the toilet, it is likely to break.
•     Remove tank from Cup. It will be set by a pair of bolts near the center of the cup where it is attached to the tank. These bolts pass from inside the tank through the mounting flange on the back of the cup. Simply remove the nuts and remove the cup from the gasket. If the bolts are rusty and the nuts are difficult to desenrroscar, wet the bolt assemblies for a few minutes with a lubricant. Place the tank in the most remote place possible, if it is out of the house better.
•     Remove the bolt covers from the toilet base and remove the adjustment bolts. Some toilets have four adjustment bolts that hold them to the floor. Most of them will have only two.
•     Move the cup to remove the wax gasket. Unless you want to bring the cup directly outside, have a piece of paper or plastic ready to place. The gasket will be dirty and sticky, and the wax of a cup gaskets is a difficult material to clean from any surface.
•     Cover the drain hole to prevent the fumes from escaping into the room. Do so that your stopper (cloth or other) does not fall down the drain and tape it.
•     Use a flexible spatula to sand the wax or putty from the Cup base and floor mounting flange.
•     Clean and level the installation surface before installing the new toilet.

How to repair damaged flanges

Toilets can be installed in two ways. The adjustment bolts may have flat heads, which are inserted into the slots in the flange. In this case, the cup is secured to the same flange; The flange serves as a toilet support.

The second class of adjustment bolts have screw type threads at one end and bolt thread on the other. These adjustment bolts hold the toilet directly to the floor. The flange in this type of installation acts only as a support for the wax gasket and does not support the cup clamping pressure.

Once you have removed the previous toilet, you may find that the flange on which it is installed is damaged. Flanges can be made of many materials, such as cast iron, copper, brass and plastic. If the flange is badly damaged, you can ask a plumber to replace it. If it is not too cracked or broken, you can make a simple and permanent repair with a special tab that is placed under the edge of the flange.

This tab has a hole through which the adjustment bolt is placed. After the bolt is inserted through the hole, the tab is placed under the flange edge on the broken part. When tightening the adjustment bolts, the tab presses against the underside of the flange edge, which holds the cup in place.

Of course, if the toilet is installed directly on the wood floor and not on the flange itself, the seat of the flange (the inner circle against which the wax will be sealed) is the important thing. If the flange is cracked or broken inside, you will need to replace it.
How to install the new toilet

Always refer to the manufacturer's instructions for the purchased model.
How to place the Cup

You can install a new toilet the same way you removed the old one, in pieces.

•     Insert the adjustment bolts if they are the type that are inserted into the flange and place them on a line parallel to the wall behind the toilet. If they are of the type that is screwed on the floor, place the new bolts in the place of the old ones.
•     Turn the bowl over the floor. Place something underneath (a rug or blanket) to prevent damage. Install the wax ring on the waste outlet with the tapered end facing the toilet. The debris outlet is the bump from the base of the toilet that extends to the flange. A hardened wax ring is softer and more malleable. If you bring your ring from the cold outside, allow it to heat before performing this step.
•     Disconnect the waste drain hole and place the toilet on the flange. Install the washers and retaining nut without tension. Make sure conical washers are installed with the right side up. These washers are labeled in the manufacturer's instructions.
•     Place the toilet and gently press down against the wax ring and the flange with an oscillating motion.
•     Once the cup is in place, tighten the nuts on the adjustment bolts, alternating side-to-side, so that the pressure is evenly distributed.
•     Install the bolt caps on the adjustment bolts. After the installation is complete and check for leaks, you can seal the toilet base with sealant. You can use silicone sealant for bath and Bath. It can be applied from the tube and straightened with a damp finger.

How to install the tank

•     Install the large rubber ring over the outlet on the tank base according to the manufacturer's instructions.
•     Insert the tank mounting bolts and rubber washers from the inside of the tank through the bowl mounting area.
•     Place the tank in place and tighten the nuts alternately until the tank is securely attached to the cup. Again, do not overtighten.
•     Install a toilet seat according to the manufacturer's instructions.
•     Install the water supply line. If you use the new flexible water supply line, this step is easy. If you use a rigid supply line, you will need to bend it a bit to fit it. Don't curling the line. This will clog the water flow and weaken the line, so it may break or drip.

How to adjust the discharge mechanism

After changing the toilet it will be necessary to verify its operation and it is possible to make some minor changes to the discharge mechanism. Try pulling the toilet chain to see if it works and if you need any change. Follow manufacturer's instructions.

Cleaning the toilet with hygiene and removing brown spots

Cleaning the toilet with hygiene and removing brown spots

The toilet of the bath is one of the places of the house that more germs and bacteria accumulates. In many homes, the toilet Cup attracts dirt constantly. Residues of urine or other types of waste require constant revision. Therefore, when it comes to cleaning bathrooms, we recommend that the toilet become the place that most attention lend.

Toilet Bowl Ring Remove Product

Clean restrooms and other cleaning products you should use

Rubber Gloves will be your best allies in this cleaning job. They will isolate your hands from germs, and turn the experience into something more enjoyable. To ensure the hygiene of the bathroom and clean the toilet properly, also has paper and some cloths, we recommend the microfiber. As a cleaning essential product choose the lye. Their hygiene and disinfection capacity are very high. If you also choose the one that is less harmful to the environment, the better. Finally, you also have a scouring pad, with the "Most of the dirty work" and you will be able to rub the surfaces OF the WC properly. Do not use those that are metallic. They will scratch the toilet and the cleaning won't be greater.

Cleaning the outside of the toilet

Since the part of the toilet with which our body takes more contact is the outside, it will be to which we devote a special care. First, rinse the scouring pad we will use in the lye . As commented above, we recommend those other than metal. Once rinsed, rub with the necessary force, starting from the lids to reach the sides and the top. Once everything is correctly soapy, we will pass to use microfiber cloths. With them moistened, we will make a second review all over the surface, removing the remains of lye that has left the scourer. The toilet should be damp, but not wet. To dry it completely, it is ideal to use newspaper papers.

How to clean the TOILET inside

For cleaning the inner part, look first at the amount of water in your toilet. If it is a lot, you will have to empty it, because in another case it is difficult to access some of the areas of the WC. You can do it by closing the key and pulling the chain. Lift all the lids, rub with the scourer on your inner face and proceed as you indicated you should do when cleaning the outside. Once you have climbed and soapy, you can take advantage of them while drying to clean the innermost part and remove the scale that accumulates. This, in addition to tarnishing the aesthetics of YOUR toilet, is very difficult to remove. We tell you some tricks to make it easier.

How to remove scale from the TOILET

To complete the cleaning and leave it spotless, we only have to clean the toilet with brown spots and clean the scale. Although there is a good range of alternatives, let's talk about one that cleans effectively and is completely natural: the formula of white vinegar and lemon.

White vinegar and lemon to clean the scale of the WC.

As we wrote in previous posts, the lemon is a potent natural disinfectant. Its combination with vinegar offers very good results. In addition to serving you to remove the scale naturally, the lemon fragrance will leave a smell less strong than other products that remove the scale. For cleaning, pour approximately half a glass of white vinegar combined witha lemon juice. With a different pad than the one used, vigorously rub the area of the toilet with tartar or brown spots. The results will surprise you.

You already have a complete guide to clean the bathroom toilet and all its parts. We hope you will put all these tips into practice. Soon, we'll talk about how to clean the bathroom tiles and increase their hygiene.

How to remove waste from the toilet

How to remove waste from the toilet
The residues of saltpeter are as disgusting and unpleasant as their name. Deposits can form where there is heavy water.

Toilet Bowl Ring Remove Product

When this happens, Scrubbing Bubbles® Power Stain destroyer Toilet Bowl Cleaner Fight against the accumulation of saltpeter. The green liquid turns blue as it falls.

Once you have cleaned it, you can keep the cleaning with the Scrubbing Bubbles® Fresh Gel Toilet Cleaning System. Just place a gel mark under the edge and achieve fresh cleaning every time you pull the lever. In this way, the waste of the saltpeter does not feel comfortable and disappears.

Whether there is hard water or not, the waste of saltpeter does not deserve to have the opportunity. Not while Scubby is in charge!

How to do it

•     Lift the toilet cover.
•     To remove the lid, press the two texturized side surfaces and unscrew completely.
•     Tilt the bottle to fill the beak.
•     To remove the waste from the nitrate and rust, apply the product to the toilet bowl and wait for 15 minutes to settle. In case of a large accumulation of waste from the nitrate or oxide, apply the product again and let it rest until the other day.
•     Brush the entire cup and pull the lever.
•     Cover the container and close it until you hear a "click".

In the case of stains that are difficult to remove, allow Scrubbing Bubbles® Power Stain destroyer Toilet Bowl Cleaner Act for a few minutes.

5 PRACTICAL TIPS ON HOW TO REMOVE SCALE FROM THE TOILET QUICKLY

5 PRACTICAL TIPS ON HOW TO REMOVE SCALE FROM THE TOILET QUICKLY

Eliminates the task of cleaning a toilet with these smart tips and tricks. Simple household products will help your bath shine, but with our cleaning shortcuts, the idea of how to remove the scale is much easier, avoiding the rings in them, in order to be comfortable with our toilet. Few jobs are not inducers to clean a toilet. Nobody wants to get close to their dresser, but it's a necessary task. We have developed some tricks for.

Toilet Bowl Ring Remove Product

Most of our tips require little or no contact with the actual toilet. They also put common household products into work, so it is not necessary to stock up on elegant cleaning products.

1
USE VODKA
Take that cheap bottle of vodka that has been occupying the cabinet space for too long and use it to make your bath shine. Pour 1/2 cup of vodka into the toilet bowl each month to prevent rings from forming.

2
POP IN DENTURE TABLETS
Rushed? For super-fast cleaning, place a tablet or two dentures in the toilet bowl. The effervescent action will provide a quick mini-cleaning in minutes, without the need to use a scale-removing brush.

3
Draft
Rushed? For super-fast cleaning, place a tablet or two dentures in the toilet bowl. The effervescent action will provide a quick mini-cleaning in minutes, without the need to use a scale-removing brush.

4
WATER WORKS
Pour a bucket of water into the toilet bowl before covering the inside with a cleaner.

This will empty the toilet without causing a filling of the bowl. The reduced water level allows you to place the cleaner directly into the toilet for deeper cleaning.

5
COVER WITH CLEANER
To expedite the cleaning process, cover the toilet bowl with cleaner before doing anything else.

Then continue with the handle, seat, tank and any other area you would like to disinfect. When finished, the toilet bowl cleaner will be soaked. Rub and clean.

Cleaning stone for lime in toilets

Cleaning stone for lime in toilets

The use of cleaning stone or pumice stone is not yet widespread for sanitary cleaning. And from ClimProfesional we want to show you the advantages of its use.

Toilet Bowl Ring Remove Product

It is often that in homes and offices or public toilets we find toilets where there are some dirty rings to the lime rings in toilet.

Lime rings in toilet

Water level height, and lime deposits embedded under water level.

Those deposits seem almost impossible to eliminate. And usually appear in toilets that are used less frequently and in areas where the water contains more lime.

Although there are specific anti-limescale cleaners, suitable to remove these remains, we want to offer you another ecological solution: the cleaning stone.

The cleaning stone is made of cellular glass and has a strong descaling acid power. If you haven't used it before, this stone has a similar effect to the pumice stone. Yes, that same stone used at home to remove the excess skin from the bottom of the foot as well as the hardness.

Why does the cleaning stone work?

The cleaning stone will not damage the brightness of your toilet.

It is a eco product manufactured with glass treated at high temperatures and with the latest technologies, in a process similar to that of nature in the formation of volcanic pumice.

They are manufactured in 100% glass, a harmless material for health, non-allergenic and environmentally friendly..

Cleaning Stone to remove limescale from the toilets. ClimProfesional.

How easy is it to remove the remains of lime?

Very easy.

Clean the scraps that are easy to remove using your regular bath cleaning product.

Empty the cistern and remove all the water left in the toilet.

Clean all the water with a cloth and rub the remaining lime residues with the ClimProfesional cleaning stone.

Or in its absence with a moistened pumice stone.

And ready!!! It'll be shiny for a while.

With the use and the passage of time will reappear those remains of lime. But we've already won the battle and we know how to leave the toilet as new very easily.

How to remove the blue rings from a toilet

How to remove the blue rings from a toilet

Blue rings in the toilet bowl are typically caused by mineral deposits that are present in the water. Copper is the common culprit of blue or greenish spots. These stains can make your toilet old and dirty. Fortunately, there is no need to live with these nasty-looking stains. With a few common household items and a bit of hard work, you can remove the blue rings and restore the look of the toilet bowl.

Toilet Bowl Ring Remove Product

Instructions

• Wash the toilet and allow the container to fill with clean water.

• Insert 2 to 3 cups of white vinegar into the toilet bowl. Clean the toilet bowl with vinegar/water mixture and a bath sponge. Let the vinegar stand for 20 minutes in the bowl.

• Scrub the toilet bowl once again with the water purifier mixing and cleaning. Wash the toilet and allow the container to fill with clean water.

• Add 2 cups of ammonia to the toilet bowl. Scrub the blue rings with the ammonia-water mixture and a bath sponge. Let the mixture sit in the cup for 15 minutes.

• Clean toilet Scrub with ammonia-water mixture and sponge. Continue scrubbing until the blue rings are no longer visible. If necessary, allow the ammonia-water mixture to remain for an extended period of time.

• Wash the toilet to rinse the cup. Let it fill with clean water.

• Clean the toilet weekly cup with white vinegar or a commercial toilet cleaner.

Tips and warnings

•     You can also drain as much water as possible and scrub the blue rings with a moistened pumice stone.
•     Never mix ammonia with bleach or bleach-containing products. The resulting fumes are toxic.

Removing calcium rings in Kohler toilets

Removing calcium rings in Kohler toilets

Normally, mild abrasive cleaners can clean the vitreous china from Kohler bath bowls. Strong cleaners will not only damage the surface, also remove the luster from the cup surface. Kohler reports using a stronger cleaner to cope with hard water deposits such as calcium rings that accumulate over time. Products such as Lysol bath cleaner are recommended by Kohler to clean the toilet, consider another Lysol product, or a similar product designed for hard water stains on the calcium ring.

Toilet Bowl Ring Remove Product

Instructions

• Shut off the Kohler toilet water by turning the shutoff valve behind the toilet completely to the right. Wash the toilet. The container does not fill with water, so the water level will be lower. Wash a second time to further reduce water.

• Lift the toilet seat. Apply a commercial cleaner that removes hard water deposits directly into the calcium ring inside the container. Cover the water line ring and the series of the rim holes above inside the bowl.

• Allow the cleanser to sit quiet for about 10 minutes. Leave the seat up during this time.

• Scrub the surface of the entire inner container, focusing on the holes in the rim and toward the calcium ring in the water line. Use a nylon brush to clean the bowl. Switch to a plastic bristle brush, if the nylon brush is not effective in washing the calcium rings.

• Twist the valve to the left and allow the tank to fill with water. Wash the toilet so the bowl cleaner is removed.

How to recover a wash ring in the toilet easy way

How to recover a wash ring in the toilet easy way

Losing a ring on the toilet can be a nightmare, especially if it's a relic, a souvenir or a symbol of your love. Once something is emptied into the toilet, it travels through the internal pipes of the bowl, through the pipes and sewer system or septic tank. If your ring is to pipes, the costs of ripping the pipes and septic tank will be much more than the cost of most jewelry pieces. However, if the ring is still in the toilet, there is hope. Removing the toilet is the only way to know for sure.

Toilet Bowl Ring Remove Product

Instructions

• Look behind your toilet and find the supply valve located on the water line that feeds the tank. Turn off the valve. Press and hold the lever in the tank to empty the toilet and empty the tank.

• Lift the toilet tank cover and put it aside. Place the nuts on the bottom of the toilet. Remove the nuts with the appropriate deep-well socket from the assembly. Reach into the tank and remove the retaining bolts. Lift the tank from the toilet bowl and put it aside.

• Look on the floor and find the dome-shaped plastic cap on both sides of the toilet bowl. Remove the plant covers using a flat-blade screwdriver and store them. Remove the retaining nuts by keeping the cup on the floor. Lift the toilet off the floor and place it next to you.

• Remove the nuts on the underside of the top edge of the toilet using the plastic tweezers. Pull the cup seat and reserve. Lift the toilet upside down with the help of an assistant. Shake the bath to see if the ring falls out of the jar.

• Turn the toilet bowl straight up and place it on top of a 5 gallon bucket. Spray water from a hose into the toilet bowl to try to remove the ring from the ins and outs of the toilet. Dump the bucket in the tub when necessary.

• Remove the old wax ring from the drain on the floor. Scrape the remains of the plant and the bottom of the vanity with a plastic putty knife. Clean the toilet and floor with a clean cloth. Place a new wax ring around the drain on the floor. Secure the toilet bowl at the top and replace the retaining nuts. Tighten the nuts with an outlet. Tighten plastic caps over bolts.

• Inspect the bottom of the tank to make sure the rubber is in its proper place. Back the tank over the toilet bowl. Slide the retaining bolts through the tank and bowl. Turn the nuts on the bolts. Tighten the nuts with an outlet. Place the seat on the bowl and secure with the plastic screws and nuts. Tighten the plastic nuts with their tweezers.

• Restore the water supply and see the toilet if there are leaks. Flush the toilet several times to check the wax ring. Clean the area with your VAC store rinse out the bucket and fill it with water. Add 1/2 Cup of bleach to water. Clean the bath, toilet and floor with a bleached water--soaked rag. Allow the bath to dry thoroughly before using again.

Tips and warnings

•     Gloves and safety goggles are required when using hand tools.
•     Rubber gloves and safety goggles are required when using bleach or other chemicals.