How to repair a toilet seal

How to repair a toilet seal

If you're wondering how to repair a seal toilet, you do not need to be worried since this is a simple repair job that can be done easily with some basic household supplies. Broken or loose toilet seals are among the most common causes of a leaking toilet. The toilet seal in most contemporary bathrooms is a ring-shaped seal that has an adjustable collar for a tighter installation. This seal is necessary to prevent the leakage of water and sewer gases that can contaminate the bathroom space. You can use the following guidelines to repair your toilet seal in an affordable and non-demanding manner.

Toilet Bowl Ring Remove Product

Step 1-Starting
Start by getting ready with a pair of rubber gloves. Turn off the shut-off valve or main valve that controls the toilet water supply. This valve is usually located on the wall on which the toilet cistern is secured. Rinse the toilet several times to make sure that the remaining water also drains. Now proceed to the base of the toilet, that is, where the toilet is secured on the floor of the bathroom.

Use a flat-bladed screwdriver to round the putty or putty ring. This can be tedious since the base of the toilet is well compacted at the time of installing the toilet. Use the tip of a screwdriver to open the plastic caps on each side of the toilet seat. Under the covers, you will find metal bolts that secure the toilet bowl on the floor. Loosen these bolts with a wrench and remove them.

Step 2-Dismantling the toilet flange
It is best to seek help from another person at this time to hold and lift the toilet bowl. Sometimes, the toilet bowl is not properly secured on its base and loosening the flange can cause it to fall off suddenly. Spread some old rags around the base of the toilet before attempting to tilt the toilet bowl. Ask your assistant to slowly tilt the toilet bowl. This could also cause a small waste of water retained in the toilet flush outlet along with traces of dirt for which the rags are made. This should reveal the flange bolt with the nuts that accompany it. The flange is a durable accessory, necessary to secure the toilet bowl in the underlying drain hole. The flanges are made of different materials, including cast iron and plastic. Metal flanges are difficult to handle as they can corrode. Use a sharp end of a screwdriver to remove rust. Use a wrench to loosen the nut and remove the bolt.

Step 3-Replace the toilet seal
It is best not to remove the toilet bowl, as adjusting it again could be difficult. Ask him to partner to keep the toilet bowl tilted as he goes through the repair. Using a spatula, edge the old wax ring. Replace it with the new wax ring. The seal of the wax ring should be adjusted. The new wax rings tend to protrude a little, which could damage the tight fit. Therefore, press down repeatedly on the seal. Now move towards the insertion of the flange bolts. Use a wrench to tighten the bolts.

Step 4: repair of the toilet board
Ask your associate to gently place the toilet bowl in its original position. Doing this with a tug can break the underlying ceramic tiles of the bathroom floor. Insert the metal bolts to secure the toilet bowl on the floor and tighten them with a wrench. Replace the plastic caps that you had removed at the beginning of the project. Finally, apply a thin layer of putty around the base of the toilet for a tighter fit.

How to wash the toilet? How can I clean a toilet?

How to wash the toilet? How can I clean a toilet?

To wash the bath Cup it is recommended to perform the following steps:

Toilet Bowl Ring Remove Product

1. Pull the handle from the TOILET and let the water run clean.


Como puedo limpiar bien un inodoro2. If using any product, apply and let stand for the time indicated on the label.


3. Brush very well, even on the water discharge flange and around the inside sides.


4. Let the water run again, and rinse the brush at the same time, shake very well and put it back in its base.


5. If the scale cannot be removed, apply muriatic acid (in half a bucket of water, two cups of acid and size with a broom or toilet brush), if you do not want to use the acid, tállela with a moistened water sandpaper.

Leaks in the toilet

Leaks in the toilet

Leaks on the outside of the toilet are easy to detect, but to solve them often it is necessary to dismantle the sanitary

Leaks on the outside of the toilet can cause significant damage and seepage across the floor. The advantage in this case is that water losses are easily detected. Sometimes problems are recorded in the area that joins the cup with the ground. Other times, leakages originate from watertight gaskets in poor condition. In many of these cases, it is necessary to dismantle the toilet or cistern to make repairs.

Toilet Bowl Ring Remove Product

 Problems between the toilet and the cistern

In order to solve the problems of water loss between the toilet and the cistern, it is often necessary to dismantle the latter to replace the sealing gasket and sometimes it is also possible to remove the fixing screws and the mechanism of the cistern. You have to take note of the deposit mark to buy a kit with all the necessary elements for the repair.

Then, the foam gasket is removed that allows the watertightness between the toilet and the cistern, the edges of the hole are cleaned to remove the lime scale and the new mechanism is inserted into the cistern. On the outside, the PVC nut is placed on the thread and locked to compress the gasket. Finally, a new foam gasket is installed on the nut and, again, the cistern on the toilet.

Leaks in the evacuation tube gasket

When leaks are recorded between the evacuation tube and the toilet, the latter must be disassembled. To do this, close the water stopcock, empty the cistern and disconnect the water inlet pipe to the cistern. Then it is separated from the wall and the clamping brackets are removed. To release the toilet from the floor, remove the screws that fix it. After unscrewing them, the toilet is carefully balanced to loosen the adhesive that binds it to the pavement.

    When leaks are recorded between the evacuation tube and the toilet, the latter must be dismantled

Sometimes the solution is to replace the seal gasket. In this case, after removing the toilet, remove the damaged gasket and cut the adjustment ring with a hacksaw. A new ring and elastomer gasket are then placed in place. Finally, just pull the ring to immobilize it in the neck of the tube and place the toilet in place.

Leaks in the bottom of the toilet

As time passes, water leaks can be recorded through the bottom of the toilet. Sometimes the escape is so scarce that it is barely noticeable. It may occur that the seal that joins the Cup with the floor has worn out and that this causes small puddles of water around the toilet.

To avoid the formation of moisture, fill this gasket with silicone or plumber's putty. This last product has a yellowish color that can be somewhat tarnished, so it can be painted with the same paint that is used to coat the joints of the tiles.

5 tips to eliminate lime: the best products

5 tips to eliminate lime: the best products

Lime can be a nightmare: it accumulates in the washing machine, in the taps or in our bathroom. Discover how to restore the brightness of your home.

Toilet Bowl Ring Remove Product

There are many ways to end the lime, however, we recommend the use of specialized products; There are different brands and different uses for these products: to remove lime from household appliances such as the washing machine, to leave our taps gleaming, or to finish with lime in the bathroom.

We tell you 5 tips to remove the lime permanently and we recommend the best anti-cal products on the market according to their quality-price.

Why lime is formed

Water often accumulates in cracks: between the tiles, the tiles, the faucets, the washing machine ... This water evaporates, however, its mineral residues remain.

The gradual accumulation of these mineral residues is what we call lime, which, in addition to being an accumulation of waste, offers a non-aesthetic appearance (a whitish layer that removes all shine from our tiles, sinks and appliances).

We will share with you some very useful tricks to eliminate lime in different areas of the house.

How to remove lime from the bathroom

In the toilet many bacteria are produced, therefore, a thorough cleaning every week is the best way to keep your bath hygienic and clean.

In addition to cleaning the toilet with your cleaning products, be sure to apply an anti-scale product inside the toilet bowl. Spray it with an anti-limescale product and let it act for 10 minutes. After that time, pull the chain and the water will clean the remains of the product.

Do this once a week, and if necessary, rub with the brush in the recesses in which a more visible amount of lime accumulates (once the anti-scale product has been applied).

As for the tiles, there is also the lime accumulates: being between the slits of the tiles, you must carefully apply the anti-lime product with a sponge or scrubbing pad; Leave the product to act for 5 minutes and rinse the remains of the antical with a wet cloth. Do not forget to dry the area when finished! We do not want to accumulate humidity!

How to remove lime from the tap

Removing lime from faucets requires more time; therefore, try to apply the product in a time zone in which you do not need to use that tap frequently, since you have to let the antical act for a long time (sometimes, depending on the amount of lime, can last for hours ).

To remove the lime from the tap and restore its original shine, soak a cloth of anti-scale product and wrap it with the tap in question. Another option is to rub the tap with the cloth, but in both cases it is necessary not to rinse the tap with water until after a while. If you wrap the tap with the cloth, do not remove it until after the actuation time.

With the shower head the procedure is the same, however, in this case it is advisable to disassemble the artichoke in order to reach all the nooks and crannies.

In all these cases, after time, rinse with water and dry carefully with a dry cloth.

How to remove lime from the washing machine

Cleaning the washing machine regularly is a guarantee of a longer service life and a better washing of your clothes.

Every so often (2 months, for example), fill the hot water washer and add one liter of anti-lime or bleach product to the dispenser.

With an operation as simple as this we make sure to keep our washing machine in perfect condition and a much longer durability. In the long run it means savings!

Better anti-lime products

The time has come for us to ask ourselves the big question: what is the best anti-calculus product? Which to choose?

Surely you already know some brands. We are going to recommend the brands with which we work, since, we believe, they are the highest quality for their optimal results and their effectiveness.

• -Calgon (gel)
• -Diranzio Bellido (anti-scale package for the lavavadora)
• -Codina (antical descaler)
• -KH7 (anti-scale gun)
• -Viakal (boat)
• -Viakal (spray)

Other options: salpumánico acid and phosphoric acid

There is the option to use acids to descale lime from certain areas, however, we recommend applying it with great caution, preferably by a professional.

The most commonly used acids are salpumánic acid (salfumán) and phosphoric acid. We recommend you learn how to apply them correctly before putting yourself to it for your safety and a more optimal result.

Have these tips been useful? Give us your opinion, and do not forget to tell us some other advice that you know and that we have overlooked :)

Come back to enjoy the original shine of your faucets, washing machine and bathrooms!

Toilet bowl top-features stripping

Toilet bowl top-features stripping

The problems in the toilet flushing system are not uncommon, however you can always fix them yourself, all you will need to remove the tank cap. Dismantling should be done carefully, as it may break or break. Therefore, in this article we will see how to remove the lid of a different type of toilet.

Toilet Bowl Ring Remove Product

General Information

In older models of drainage tanks, it is usually quite easy to remove the panel, simply unscrew the top of the trigger and lift it up. In modern tanks there is a drain button and a glass button, whose design prevents the dismantling of the cover.

However, in any case, this design is foldable, so this operation should not cause any special problem. The main thing is to do any action with care, without putting an excessive effort and slowly.

Before opening the toilet cistern cover, you must prepare some tools that may be necessary in the working process:

•     Pliers
•     Knife
•     Screwdriver

    Pay attention during operation with the tank, the water must be blocked. Otherwise, it can overflow and flood the bathroom.

Cover removal

At the beginning, it should be said that the lids of some models of modern ceramic containers are removed very simply, as the drain button is not connected to the trigger mechanism. To verify this, we must carefully try to lift the detail.

The following are ways to remove panels from other common types of tank designs:

•     If the water is drained as a result of raising the thrust, then before removing the toilet cistern cover, it is necessary to unscrew the ball located at the end of the handle.
•     Disassembling the container with drain buttons causes greater complexity, however, these models have become more popular recently. In this case, before opening the cover of the toilet cistern, you must unscrew the tube, inside which there are buttons. On the outside, it usually represents a ring, which must be pushed with a screwdriver or knife and turned counterclockwise.

It should be said that after this the panel cannot be completely removed, it can only be lifted and rotated a little, after which the latches of the button mechanism must be unfastened.

    The plastic tanks of the Soviet model, which are sometimes found in the apartments, have poles that must be removed before dismantling the structure with their own hands.


After the workpiece is disassembled, it must be placed in a safe place where it is impossible to hook and break it.

    Tip After repairing the toilet cistern drain attachment, it must be checked several times to operate. In particular, you must ensure that after lifting the float, the valve completely locks the water.

Cover Repair
Link

If in the dismantling process, something went wrong or the cover was broken for some reason, you can try to restore it.

For this you need to prepare the following materials:

•     Scottish
•     Epoxy adhesive;
•     Small galvanized steel plates.

The instructions for the implementation of this work are as follows:

•     First, all individual parts should be assembled in a single frame and taped. This should be done carefully so that there are no spaces where the glue can flow. To do this, all joints must be carefully taped.
•     Then the assembled structure should turn around.
•     Before gluing the toilet cistern cover, mix the glue with the hardener in a proportion of 1:10.
•     All gaskets should be carefully stained with glue and the galvanized plates must be attached from above, which will cause the product to become stiff.
•     When the glue hardens (about a day), the tape should be removed, after which the lid is installed in the toilet bowl.

Since the price of a new toilet is very high, this procedure will allow you to avoid the unplanned spending of family budget funds, while the appearance of the pipelines will not be affected.

Hole Increase

Often, home craftsmen, after replacing the drain fittings, face a difficulty: the diameter of the hole in the cap is smaller than the diameter of the reinforcement. Of course, you should not change the plumbing fixture completely, but how to increase the hole in the toilet bowl lid?

There are two ways to solve the problem:

•     Carefully drill the hole with a ceramic drill and cut out the remaining areas. The irregularities will be hidden by the cover.
•     Carefully chop the enamel with a thin drill and a hammer, then widen the hole with a round file.

In both cases, it is necessary to take great care not to divide the surface, because in this case it will be much harder to make a tank lid from the toilet bowl.

Here, perhaps, are all the main points you need to know to remove the tank cap and, if necessary, repair it.

Conclusion

The cistern cover of the toilet bowl, regardless of the type of construction of the latter, is removed quite easily. The main thing is to understand immediately what elements should be dismantled and not to make excessive efforts during work (see also the article: a toilet flush tank).

The video in this article will give you the opportunity to get additional information on this topic.

Installing a toilet

Installing a toilet

Installing a toilet is not a thing of the other world, just follow these simple steps, have a little patience and very careful and can do it easily.

Toilet Bowl Ring Remove Product

I imagine that you have the same thing happened to me once, we do an enlargement at home, for example an office, and logically we must have the toilets nearby so we do not have to cross the whole house, the ceramics are installed and then we call the Plumber , and oh surprise when we pass the bill to install a simple sink or a toilet charge us almost as we cost the same and of course no return to give we have to pay. Well, I started thinking about this matter when I finished the first bathroom of my house and decided to investigate how it is done, such a surprise when I realized that the work is as simple as "taking candy from a child" (if you please do not do that to children) , it requires that if enough patience and care.

Installing a toilet :

The first step is to acquire the toilet, do not think that they should go to the accessory store and buy the first one that comes or I like, this seemingly simple process has its complications and secret tricks; One is that they should consider saving the liquid element (for things like ecology), water is a precious and expensive, please ask them to buy toilets of 6 liters maximum, currently ay one piece models with this design; On the other hand and as more important step should consider the distance between the wall plated with majolica and the center of the sanitary outlet hole of four inches (or three if the case, although this measure is not highly recommended because it is prone to atoros) This distance should be at least 30.5 cms or 12 inches; Also the height of the outgoing drain pipe must be at least 1 cm. In relation to the finished ceramic floor . These considerations are important because not all toilets have the same measure; A variation in this matter would determine a bad fit of the sealing ring and the consequent leakage of water or annoying smells.

The good thing about acquiring modern toilets is that it already comes with the pre-installed internal accessories (for us as Bricómanos this is very convenient); Of course we must acquire other things like the water supply tube, this implement comes in several presentations: economical, usually with thread in ABS plastic and metal braided thread body less durable and I call premium, with Chrome-plated brass thread, aluminium braided body and inner reinforcement The thread size of this fixture must be 7/8 inch. We also have to supply two anchor bolts, these bolts are made of bronze and are instead of head with a removable nut to facilitate the fitting of the toilet base. A wax ring is the last implement for our project, this consists of a ring made of raw paraffin that in some presentations comes with a guide rubber that facilitates the fitting and installation (I recommend to buy in this type).

By hand all the above materials we proceed to install our toilet. A first step is to fit the toilet base into the drain hole, mark the places we drill with the drill (tip: use a 3/8 drill bit special for diamond-head cement, the hole must be previously Marked with a metal punch to avoid slipping of the bit), remove the base and perforate to insert the plastic anchors, the anchor bolts are screwed using a Stillson key (the movable head) or a self-pressure pliers (a tip: to mark the Hole location use indelible down, this if you paint on Majolica, the distance between the anchor bolts must be 16 cms. As a second step we turn the cup and fit the wax ring around the discharge hole at the bottom (tip: Do not place the toilet on the tile floor as it can chip, use the packing carton as Support). A third step is to fit the cup and adjust it with the nuts of the anchor bolts (A tip: they can "decorate" the head of the anchor bolts with ceramic plugs, sell them in the same health care provider and come in similar colors).


With the above steps we have already installed the toilet bowl or base, now we only need to fit the tank in place; To do this, simply turn the tank over and place the anti-leakage rubber that comes with the accessory kit and allow you to adjust the cup to the tank. The adjustment of the two parts of a toilet is carried out by the use OF ABS plastic regulating bolts (in modern toilets) or bronze (in the oldest), you should keep in mind that these bolts (which are placed from inside the tank) must go with their jebes to avoid leakage and in vertical position; Also be very careful in the placement of the tank, it must be positioned vertically and perfectly centered in relation to the cup (tip: Adjust the cup bolts by hand without using metal tools that can cause damage or breakage in them).

Good friends of "the housing market", we have installed our toilet, now we have to dispense with water, for this we taped with Teflon the supply tube in the part where the male thread and put a rubber inside the female thread; The male thread must first be placed in the water outlet of the wall (outlet usually ½ inch) once this is done adjust the thread on the outlet of the tank (tip: It is good to install a control key in case you miscarry a toilet accessory and cam is required Bio). Once all the above steps have been completed, seal around the cup with porcelain to make cleaning easier and prevent dirt buildup.

With these simple steps I believe without fear of mistaken that for you will be simple and gratifying to install a toilet, worth truths in these times always falls well save some pesetas and good there is no thing that makes us feel better than we do for ourselves.

How to remove cigarette burns in a toilet seat

How to remove cigarette burns in a toilet seat

• How to remove cigarette burns in a Kohler toilet seat
• Avoid cigarette burns from smoking in another room.

REMOVE THE CIGARETTE

Kohler toilet seats are made from a variety of materials such as wood, plastic and metal - none of which are completely immune to the damaging effects of a cigarette burning. Cigarette burns can stain the surface of your toilet seat, melt protective layers and burn directly through the base material. You can eliminate superficial burns on your account without professional help. However, deep burns require access to the base material and reapplying all protective coatings, which can be prohibitively expensive particularly if your seat has antimicrobial agents.

Toilet Bowl Ring Remove Product

What you need

• Gloves
• Rags
• soap holder
• Pad not to scrub
• Bathroom cleaner
• Put on rubber gloves.
• Moisten a cloth with warm water.

Pour a dime-sized drop of soap on the cloth. Rub the cloth against itself to form a soap scum.

Rub the cloth over the cigarette burn to remove debris on the surface. Place the used cloth in a bathtub or sink for sanitation or disposal.

Rub the stain with a non-abrasive sponge.

Rinse the entire toilet seat with a clean, damp cloth to remove soap residue.

Follow up with a multiple-use bath cleaner. Spray the cleaner on the surface of the toilet lid. Allow the solution to settle as directed by the manufacturer. Rinse the solution with a clean, damp cloth.

Tips and warnings

Examine the place after cleaning. If the surface of the seat has a visible gap or the cigarette burned and defaced the base material, it can safely be assumed that the protective layer has been removed.During the purchase of a new seat is easier, you can Refinish your current seat, if desired Use a high strength separation solution to remove the coatings from the seat then apply one or two coats of a high strength waterproof varnish.

Do not smoke in the bathroom or put cigarettes on the seat - the toilet seat is not an ashtray. If you can not quit smoking in the bathroom, purchase a cheaper toilet seat that can be replaced as needed.

Kohler advises against allowing chemicals to soak in the toilet seat for long periods of time.

How to clean calcium deposits from the toilet bowl

How to clean calcium deposits from the toilet bowl

Modern civilization would not be so modern without the toilet bowl. We no longer have to stoop precariously in dependencies or have disordered urinal contents. Actually, I think that running water outweighs almost any invention out there, including electricity. But it can still be more than a bit annoying when the toilets you greatly appreciate are victims of the dreaded calcium deposits. Fortunately, calcium spots are usually fairly easy to remove with a little effort and a hand or two solvent.

Toilet Bowl Ring Remove Product

Before you start in the "how" of the portion, it is always important to know some facts about the spots you are going to be attacking. First of all, "calcium deposit" is not code for anything serious. In fact, they are exactly what they seem--an accumulation of calcium and other minerals that are commonly found in your home's water supply. The bathroom is a prime spot for calcium spots because there is always some water hanging out on the plate, waiting to cause problems. Calcium spots accumulate over time, but they often feel like they appear out of the blue at night, resulting in an ugly brown/orange/pink ring around your toilet bowl once pristine.

Calcium deposits tend to be larger and worse in places with hard water or well water because there are more lime and minerals present in the water supply.

In fact, 85 percent of the water in the United States is difficult, so you're likely to face the stain more than a calcium in your life. Calcium deposits are not limited to the toilet bowl, unfortunately. They can run the water flowing rampant in any place, including the sink and shower doors, walls and shower. There are ways to keep calcium deposits from happening or get out of control. First of all, you can install a water softening system in your home.

Unfortunately those are seriously expensive, so you might not have space in your family budget. The cheapest (and most logical) method is probably just to cope with any calcium stain the instant it starts to appear. Like the tartar in the teeth, the longer you let it accumulate, the harder you will have to work to get rid of it.

If the container is already flooded with calcium stains, don't be afraid! Take a look at the following page for helpful tips on how to delete quickly and easily.

Calcium deposits are not all bad!
Of course, calcium deposits are unsightly in your bathroom and kitchen, but water containing calcium and magnesium can actually help you and your family reach some of your daily nutritional requirements!

Tips to remove calcium deposits from your toilet
Even if calcium deposits have established their residence in the toilet, there is no need to throw their hands in the air and buy a new one. Instead, use one or more of these techniques, and you're going to see some squeaky-clean results. Well, for a toilet, anyway. First of all, try the green route! A mild, natural acid, such as lemon juice or vinegar, can be very effective in pinching calcium deposits in the bud. Depending on the severity of the stain, the liquid may have to be re-applied and rubbed vigorously several times with sandpaper or rag.

Another option that many experts in DIY swear by IS plumber's cloth. Available at any hardware store, you can only use a single, plain water section to make stubborn stains disappear. If you don't mind some common household chemicals, pick up a bottle of commercial toilet cleaner for homework. Some users prefer to drain the toilet bowl first because it prevents the dilution water from the power of the VAC. Drop-ins tank are also effective in cleaning and preventing stains, although it might take some time to completely erase the stains from your bowl. If none of the simplest options are doing the trick, there are a couple of more risky ways to get the results you want. For example, muriatic acid can get rid of calcium deposits in a matter of seconds, but it is also very porcelain and dangerous to use if you do not know what you are doing.

First, be careful to make sure that the area is well ventilated due to the risks of smoke. Also, be sure to wear eye protection, rubber gloves, and clothing that covers your skin completely. Then, pour 5 gallons or less of water into the cup, followed by the careful addition of 12 ounces of muriatic acid. Then use a long-handled bath brush to carefully extend the solution around the stain. This step may have to be repeated several times during the next hour or two, but doing so must completely eradicate the mark. If you leave the room at any time, be careful to close the lid and safeguard that no child or animal can come into contact with water.

Another option of last resort is pumice stone, available in many dollar stores and hardware. Just use it with running water to wash the stain, but do it very carefully. Hard stone can irreversibly damage the porcelain, and you don't want to change one unfortunate look for another.

HOW TO CLEAN THE YELLOW SPOTS ON THE TOILET?

HOW TO CLEAN THE YELLOW SPOTS ON THE TOILET?

How many times have we entered a service, in a house or in some elegant offices and we have encountered those nasty yellow spots on the toilet, sometimes with a more intense color remarking the water level, if we knew how easy it is to get rid of They were sure that we had made them disappear for a while. The fact is, they're there and they don't look good.

Toilet Bowl Ring Remove Product

Materials:

• White vinegar
• Nylon Bath Brush
• Coke
• Bleach or Clórox (Bleach for Hispanic America)
• Sandpaper (for grandma's trick)

Note: Always wear gloves throughout the procedure and in the final part of the finish to clean the chair (which few people do) and around the toilet; At the end you should wash your hands when working in places in the home that may have more microbes.
Make the first step the night before.



TO REMOVE Stains Yellows TOILET Bowl:
1. Discharge the cistern and when the water settles and will not use it any more, pour a cup of white vinegar (this is the type of vinegar that has the expected effect) and let it rest overnight.

2. In the morning, scrubbing with the brush or nylon brushes, if you have gloves with a nylon brush will do a lot more strength against the stain, but some people still with gloves do not dare to put your hand inside the toilet bowl.

3. Pour a can of Coca Cola into the toilet bowl and let it sit inside for at least one hour. Unload the toilet and clean the toilet bowl and with a nylon brush the rest of the day use your bathroom as usual.

4. Pour a cup of chlorine bleach into the container and leave all night. In the morning, the stain will be gone.
Although it seems a little wasteful that spend two nights, it is very important to remember that these stains last years in the homes without anyone doing anything, the two nights make "loosen" the mark better.

5. If you see any traces, moisten a little Vanish on the brush and rub a little more vigorously.

Granny Trick to remove the water level mark in the toilet bowl:
Moisten a pumice stone without any product or foam so you can see well through the water and begin rubbing the stain gently with the stone; Make it very soft and without pressing too much, this solution is extreme and we know that the pumice is very abrasive and can scratch the toilet.

Thank you for consulting our easy and economical procedures.

Remove the yellow stains from the bathtub

After a long day it is nice to go home, rest and take a relaxing and warm bath. Soothes the muscles, soothes the mind and magically helps a stressful day fly away.

But how relaxing can your bathroom really be if you are greeted with unpleasant yellow spots? Yuck!

With a little help from Benjamin Franklin's PLUMBing Bay area, this DIY guide provides an effective method to clean a colorful tub – so you don't have to think twice about going into your hot tub!

Remove stains from the tub: follow these simple steps

Before jumping straight into the tub cleaning mode, it is important to consider the type of bathtub you have when it comes to bathroom PLUMBing.

You need to determine if it is porcelain, enamel or acrylic because you don't want to make the stain even worse by using an improper cleaning strategy!

If you have a porcelain bathtub, pour some Ajax or kite directly into the tub stain (enough to cover it completely). Add some water and rub with the abrasive side of a sponge. If you rinse the affected area and still see a defect, use a pumice stone to lift the rest of the stain.

If your tub is made of enamel, pour a generous amount of shampoo that you use for your hair directly in the dislocated area. Let stand for a few minutes, then rinse with lukewarm water. The stain should disappear since discoloration is probably caused by an accumulation of human oils that the shampoo can face.

If your house has an acrylic bathtub that has a stain or two, try applying a mixture of water and vinegar to the affected area. Then let it sit and suck for about 45 minutes. Continue soaking with a good sponge to rub and rinse with lukewarm water.

Fix flushing in the toilet

Fix flushing in the toilet

The toilet is one of the elements that can cause the most problems in the house. The most normal thing is that it gets jammed. However, leaks are also a common problem in these. Leakage from the outside of the toilet may cause damage, as well as seepage through the floor.

Toilet Bowl Ring Remove Product

The toilet is one of the elements that can cause the most problems in the house. The most normal thing is that it gets jammed. However, leaks are also a common problem in these. Leakage from the outside of the toilet may cause damage, as well as seepage through the floor. Other times, these leaks may have their origin in joints that may be in poor condition. To solve this type of problem, many times there is no other than to dismantle the toilet or the cistern in order to repair it.

If you notice that there are leaks between the toilet and the cistern , the latter must be removed to replace the sealing gasket. It may also be necessary to remove the setscrews as well as the cistern mechanism. Take note of the deposit mark to purchase a kit with all the necessary items for repair.

Then you will have to remove the foam gasket that makes it possible to seal between the toilet and the cistern. Cleans the edges of the hole to remove limescale and introduces the new mechanism into the cistern. Then, by the outer zone, you must place the PVC nut on the thread and lock it to compress the gasket. The last step will be to install the new gasket on the NUT, and again, the cistern on the toilet.

In the evacuation tube and the sanitary

Another problem may arise if the leaks are between the evacuation tube and the toilet. If this happens, you must dismantle the latter. To do this, you must close the water stopcock, empty the cistern and disconnect the water inlet pipe to the cistern. Then you must separate it from the wall and remove the clamping brackets.

In order to remove the toilet from the floor, you must remove the screws that keep it fixed. One of the solutions can be to replace the seal gasket of the cuff. In this case, after removing the toilet, remove the damaged gasket and cut the adjustment ring with a hacksaw. Once done, pull the ring to immobilize it in the neck of the tube and place the toilet in its position.

You can also find leaks at the bottom of the toilet. This can occur from the seal that attaches the cup to the floor. It may have worn out over time. To prevent moisture from forming, fill the gasket with silicone and ready.

TOILET SEAT FOR TOILET WITH SOFT CLOSURE SYSTEM

TOILET SEAT FOR TOILET WITH SOFT CLOSURE SYSTEM

In the universe of lids toilet seat, there is a wide variety of models. There are wooden, PL features and in both cases also different hardware options.

For these times the seat covers with soft closure or damped CA, are gaining ground against the AC da manual.

Toilet Bowl Ring Remove Product

A system in which the lid falls slowly towards the ring of the toilet causing a sense of harmony as opposed to the impact it implies when the manual descent fall, therefore have a better sound insulation. They are easy to install and remove because their upper anchorage allows the lid to be removed quickly if compared with the conventional fixing of screws and adjusting nuts. Its compact metal hardware gives it greater stability and a firm fit. The soft-closing lids are of Urea, a compact plastic material that impeccably confronts the humidity generated inside the bathroom without degrading the material over the years.

With these options we have other design variants, since these lids allow, by their manufacturing process, to intersect straight lines and curved shapes with total precision. At the beginning they entered the sanitary market in the high-end lines but today we can find them also in the models of medium range and soon Ferrum will launch this product for the lines of the low segment. A different touch that enhances the bathroom with originality and functionality.