How to clean the grout if it dries completely

How to clean the grout if it dries completely

Grouting between the tiles helps keep them in place and prevents water seeping into the ground below. Portland cement is the main component in most grouts. When cement hardens, it can be difficult to remove. For this reason, a quick cleaning after any tile project is a must. If some points have been lost during grouting or delayed cleaning, do not turn to a metal tool for assistance. When it comes to eliminating dry grout, a nylon sponge is your best friend.

Grout Cleaner Product

Instructions

1 pour 1 gallon of hot water into a bucket. Add 1 cup granulated white sugar. Stir with a wooden paint bar until the sugar dissolves.

2 pour the water with sugar on tile areas containing dried grout. Of any pouring directly from the sugar-water spoon or shovel with a plastic cup.

3 Let the water with sugar sit on the tile for about two hours. The two hours soaking will give the time water with sugar to loosen the grout from the tile.

Scrape 4 larger pieces of tile grout using wood paint stick. Exfoliating distance dried grout using a high-strength nylon sponge. Keep the surface of the tile moist at all times with sugary water.

5 Clean the clean tile with a cloth moistened with clean water after the dry grout is removed. Polish the tile to a shine with a dry cloth.

Tips and warnings

•     Wiping the tile with a damp cloth immediately after grout minimizes further cleaning.
•     Do not use metal spatulas or any other type of sharp metal instrument to remove dry grout or risk damaging the tile.

How to clean grout on tile joints

How to clean grout on tile joints

If after scrubbing the floor you think it still does not look clean enough, it may be that your problem the correct cleaning of the ground joints to remove the grout that is still embedded. Cleaning it will require an extra effort, but don't worry that if you do it properly it doesn't have to be complicated.

We have the alternative to clean with natural and organic products or with the chemicals found in the supermarket. No matter what your preference, we tell you how to clean the grout in tiles so your floor is really clean.

Grout Cleaner Product

Steps to clean grout in tiles

Follow these steps to remove grout in tile joints without much effort.

1. It is not new that we recommend cleaning with baking soda, usually very effective and affordable for routine cleaning. In this case, to remove the grout we will create a mixture of bicarbonate with water. You need 3 parts of baking soda and a piece of water. Mix until thick dough is formed. Spread that dough on the board and keep in mind that if you do it with your fingers it is advisable to use rubber gloves to perform the cleaning.

2. Another of our secrets is to use vinegar for ecological cleaning. The second step you must follow is to mix in a water sprayer with white vinegar. And spread this mixture over the bicarbonate you previously applied to the joints. You will see how bubbles immediately begin to emerge that will be the sample that the chemical reaction has started and that the mixture is working.

3. This bubbling chemical reaction should last for a few minutes. When it is finished it will mean that the mixture has done its job and that you can proceed to remove it. Use an old toothbrush to scrub the joints with the mixture and remove dirt.

4. To close with a golden brooch, scrub the floor with water. This way you will eliminate the bicarbonate residues and by the way you can eliminate the dust or dirt that has been left in the ground.

Additional Tips for cleaning grout

For extreme cases it is likely that this homemade housekeeping trick will not end up solving the problem. When this happens, we recommend using a vaporeta so that the pressurized water will definitely remove the grout. And the dirt accumulated in the joints leaving as new. If you do not have a vaporeta at your fingertips we recommend the Express cleaning team. That in all their work they use this type of machinery to thoroughly clean more than 200 areas of your house.

In addition, its 10 years of experience let you know the best way to clean different types of soil and surfaces inside the home. Do not wait for a thorough cleaning of your home and extend the life of your furniture and appliances. Calculate your price in our Online calculator of floor and house cleaning and you won't regret it.

How to Clean Tile Grout

How to Clean Tile Grout

Grout these days, is it still white or does it have a different color? Don't worry there are ways to control that mold, dirt and grime that cling to those cracks. 

First of all do not go to waste your money on products that are not able to do what you are looking for a complete cleaning, when the cheap and healthy solutions are in our home.

Grout Cleaner Product

Prepare to start cleaning! Then I mention some tips for cleaning the same.

Best ways to clean tile grout

When we talk about cleaning the grout you probably already have what we will use at hand. Besides, we'll need a rag and a toothbrush.

Vinegar 

We can either pour the vinegar directly into the grout or lower it with water. Then poured it on the edges of the grout. Let it rest for 10 minutes. And finally we use a toothbrush with a circular motion.

Vinegar + baking soda

These 2 are a fantastic duo because when you join fight against dirt very easy. We make a bicarbonate paste with a little vinegar. Rub the grout with the pasta and the toothbrush. Finally wipe the waste. It's slow but the results are fantastic believe me it's worth the effort.

Lemons  

The lemons came! The high acidity in the juice of the lemons corrodes the difficult stains and the discoloration of the grout. Poured the lemon in the grout. We let it act for about 10 minutes before cleaning. If you realize the smell of fresh lemons is much better than the Limpadora solution.

How to clean the really hard stains from the tile grout

Without ever it occurred to clean the lines of your grout for years (do not ashamed sometimes happens) if this comes to pass is the time to bring the big fish. Here I leave the best ways to clean the grout, when stubborn dirt does not want to go out.

Hydrogen peroxide 

Because it has oxidizing properties, this liquid is the most spectacular cleaning solution for many household needs, especially tile grouting. It is much safer than chlorine bleach or ammonia-based products, and best of all less expensive. We make a mixture of peroxide with water in a container half and half. Poured our mixture in the grout. Let stand for 10 minutes before scrubbing away with the toothbrush.

Betun of white Shoes

If you want to know the trick?, and if not lost the hope of getting a white grout?, the time has come to be creative. We apply white-colored shoe cream and let it rest all night. The enamel is easily cleaned, but the color will remain in the grout.

How to clean the grout between the tiles

How to clean the grout between the tiles

Even after scrubbing the floor, the tiles with the dirty grout may still look dirty. Leave your floors as new cleaning the grout as well. Depending on the type of tile and the color of your soil grout, there are different cleaning methods that you can use to renew your appearance. Whether you opt for chemical cleaners or more natural methods, grout can be spotless with little effort.

Grout Cleaner Product

Method 1 With baking soda and vinegar

    1

•     Make a paste with baking soda and water. Mix 3 parts of baking soda and 1 part water to make a thick paste. This versatile cleaner will clean grout of all colors, but vinegar can be detrimental in some natural stones, such as marble or limestone.
•         Apply the pasta to the grout lines with your finger.
•         Although baking soda is not harmful, the use of rubber gloves can help prevent scratches or irritations from rubbing the grout with baking soda.

    2

•     Make a solution of 1:1 of white vinegar and water in a spray bottle. Spray the vinegar solution into the sodium bicarbonate paste you applied. You will immediately see bubbles, which will tell you that the natural cleaning process has begun.

    3

•     Wait for the solution to stop bubbling. Bubbling is a chemical reaction between sodium bicarbonate and vinegar. This reaction usually lasts for a few minutes. After the bubbling is completed, the chemical cleaning action will have culminated.

    4

•     Scrub the grout with a brush. With a nylon bristle brush, or a toothbrush, scrub along each grout line. Pay attention to the corners and edges to clean them well. [1]

    5

•     Scrub the floor with water alone. Use a mop with water alone to remove the residues of baking soda and vinegar. Rinse the mop and change the water followed during the cleaning process so that you do not spread the waste on the floor.

Method 2 Clean with sodium percarbonate

    1

•     Dissolve 2 tablespoons of sodium percarbonate in 2 cups of lukewarm water. Make the solution immediately before using it to get the best results. Mix the solution well to ensure that the sodium percarbonate is fully activated. The bleaching power of sodium percarbonate could damage the color grout, but it is soft enough for all types of tile.

•     2
•     Make a test in a little visible grout corner before cleaning up all the sleep. Some tiles or grouts may be bleached or discolored by sodium percarbonate. Apply a little of the sodium percarbonate solution to a discrete section of the grout to make a color test.

    3

•     Pour the sodium percarbonate solution into the grout. Make sure you throw enough to cover all the lines of the grout. Clean the floor section by section to not wet it completely.

    4

•     Use a nylon bristle brush to soak the sodium percarbonate solution in the grout. Leave this solution acting several minutes to get the best results. [2]
•         Scrub the grout with the brush from front to back.
•         Be sure to scrub the corners and around the edges of the floor, as dirt and dust tend to accumulate there.

    5

•     Insert the brush into the powdered sodium percarbonate to increase its cleaning power. If you see a darker or more visible spot, you can make a solution of stronger sodium percarbonate by inserting a wet brush directly into the sodium percarbonate powder.
•         NOTE: Pour a little of the powdered product into another container to avoid adding water to the main container of powdered sodium percarbonate.

    6

•     Rinse the floor with water and then dry. Pour clean water directly into the tiled floor and dry with a clean scouring pad or mop.

Method 3 Clean the grout with oxygenated water, sodium bicarbonate and liquid dishwasher

    1

•     Make a dough. Mix ¾ cup of baking soda, ¼ cup of oxygenated water and 1 tablespoon liquid dishwasher. This highly effective paste cleans the grout in 3 ways:[3]
•         Sodium bicarbonate acts as a natural abrasive to rub the grout.
•         Oxygenated water reacts chemically with sodium bicarbonate, which releases bleaching oxygen ions.
•         The dishwasher liquid helps to loosen dirt and remove grease.
•         NOTE: The whitening action of the chemical reaction may affect the color grout. Make a color test in a slightly visible corner before cleaning the entire floor.

    2

•     Apply the pasta with a nylon bristle brush. A toothbrush or a nylon brush will do the trick. Make sure to apply the pasta to the grout between the tiles and around the edges to make them evenly clean.

    3

•     Let the mixture act in the grout for about 15 minutes. You'll see a bubbling reaction as sodium bicarbonate and oxygenated water interact. Give it time to soak in the grout and you can remove the stains.

    4

•     Rinse the grout with warm or warm water to remove the entire solution. Pour some water directly onto the tiled floor to remove the grout solution.
•         Be careful, because a wet tiled floor can be very slippery.

    5

•     Use a scouring pad to clean the grout and remove any debris from the product or dust. Remove the remaining dough from the grout by lightly scrubbing the floor with a scouring pad. You can do it stopping on the sponge and move with both feet or you can go scrubbing the floor while you go wiping to Gatas.

    6

•     Scrub the floor with clean water. To make sure there is no residue or foam, scrub the floor thoroughly with a sponge or cotton mop. Rinse the mop and change the water followed so that everything is clean.

Method 4 Clean the grout with a vaporizer

    1
    Rent or buy a vaporizer. Vaporizers effectively clean and disinfect all types of tile and grout because they do not use any chemicals. Go to your local home maintenance store to rent or buy one of those machines. Make sure the vaporizer you get has the right accessories to clean the grout:[4]

•         Steam Hose
•         Small brush

    2
    Follow the manufacturer's instructions for assembling and filling the vaporizer. Read the instructions carefully to avoid damaging the equipment.

    3
    Fill the container with clean water to the line indicated in the instruction manual. Do not add chemicals or detergents to the water container of the vaporizer.

    4
    Turn on the vaporizer and let it heat up. The vaporizer's instruction manual will tell you how long you have to wait after turning on the machine for use.

    5
    Move the cleaning brush back and forth over the grout. Start on one side of the room and go forward to the other end. The steam will lift dirt and dust from the grout, and also kill any mold you may have.

    6
    Use a scouring pad or mop to clean up excess water after cleaning. Be careful, because the floor may become slippery after the steam is condensed in water.

Tips

•     You should always first try a new cleaner or cleaning solution in a slightly visible area before using it to make sure it will not damage the tile or grout.
•     If you are using sodium bicarbonate or sodium percarbonate solutions, do not do more than necessary, because these solutions lose their power quickly.
•     After cleaning the grout, apply a sealant to make the cleaning last longer. [5]

Warnings

•     Do not use hard-bristle brushes such as steel or wire bristles, as they may break and damage the grout.
•     Do not use vinegar in marble, granite, travertine or other natural stone floors, as this may cause the surface to be carved and permanent damage. Grouting These surfaces should only be cleaned with a neutral pH solution. [6]

Things you'll need

•     Cube
•     Sodium percarbonate
•     Clean water
•     Nylon Bristle Brush
•     Mop
•     Sodium bicarbonate
•     Toothbrush
•     Spray

How to replace a Kohler toilet tank

How to replace a Kohler toilet tank

Kohler toilets are one of the most popular toilet brands in the United States. They are well manufactured, efficient and come in a variety of styles. However, even Kohler toilets will suffer wear and tear. Replacing a defective part of the toilet, like the tank, can be simple or require a little more time, depending on your Kohler model. You can quickly change a Kohler two-piece toilet tank. But you will have to take out the entire toilet to replace.

Toilet Bowl Ring Remove Product

Two-piece toilet
Turn off the water supply in the wall. You can find the shut-off valve by following the inlet hose from the tank to where it is connected to the wall.

Unload the toilet to remove the water. Wipe off any remaining water with a sponge and towels.

Unscrew the inlet hose.

Separate the Kohler tank from the base by unscrewing the two bolts inside the bottom of the tank. On most models, the bolts inside the tank have a screwdriver head, which allows you to use a screwdriver to keep the bolt stable while unscrewing the nut at the other end with a wrench. Or you can keep the key firmly on the nut at the bottom and unscrew the bolt.

Remove the bolts and washers. Gently lift the tank and out of the way.

Install the new Kohler toilet tank as you align the two bolt holes in the tank with the holes in the bowl and align the tank gasket with the inlet port in the bowl.

Pass the bolts and washers back into the tank holes once the tank is in place. Screw the nuts and washers onto the end of the bolts and tighten by hand.

Tighten the nuts a few turns with the key. Turn on one side and then on the other. Alternate the sides to maintain even pressure.

Add a few drops of glue or plumber's tape to the water inlet connection in the tank. This will ensure a tight connection. Then screw the water inlet hose. Squeeze with a wrench.

Turn on the water and allow the toilet to fill. Check for leaks.

One piece toilet
Turn off the water supply, clean the water and disconnect the hose following the steps above.

Unscrew the bolts at the base of the bowl that hold the toilet to the flange.

Gently shake the toilet back and forth to loosen it from its fit. Then lift it up and out of the way.

Wipe the remains of the old wax ring on the flange and install a new wax ring in place.

Insert the new flange bolts into the flange.

Turn over the new Kohler toilet. Add a thin strip of putty or plumbers putty along the bottom of the tank. This will help ensure an airtight seal between the cup and the floor.

Lower the new Kohler toilet into the wax ring, making sure the flange bolts seat through the holes in the base.

Press the toilet gently on the flange to make sure it is positioned on the ring.

Thread the nuts and washers onto the bolts on the bottom of the toilet. Hand tighten, then squeeze one side at a time with the key.

Things you will need

• New tank
• New one piece toilet
• Towels and sponge
• Wrench
• Screwdriver
• Plumífero, adhesive tape and putty
• Wax ring
• Disposable gloves

Tip

• The above steps are a guide to use in conjunction with the manufacturer's instructions.
• Warnings
• Do not over tighten the nuts or the porcelain could break.
• When cleaning wax rings, wear gloves; This part of the bathroom is full of harmful bacteria.

How to repair a toilet seal

How to repair a toilet seal

If you're wondering how to repair a seal toilet, you do not need to be worried since this is a simple repair job that can be done easily with some basic household supplies. Broken or loose toilet seals are among the most common causes of a leaking toilet. The toilet seal in most contemporary bathrooms is a ring-shaped seal that has an adjustable collar for a tighter installation. This seal is necessary to prevent the leakage of water and sewer gases that can contaminate the bathroom space. You can use the following guidelines to repair your toilet seal in an affordable and non-demanding manner.

Toilet Bowl Ring Remove Product

Step 1-Starting
Start by getting ready with a pair of rubber gloves. Turn off the shut-off valve or main valve that controls the toilet water supply. This valve is usually located on the wall on which the toilet cistern is secured. Rinse the toilet several times to make sure that the remaining water also drains. Now proceed to the base of the toilet, that is, where the toilet is secured on the floor of the bathroom.

Use a flat-bladed screwdriver to round the putty or putty ring. This can be tedious since the base of the toilet is well compacted at the time of installing the toilet. Use the tip of a screwdriver to open the plastic caps on each side of the toilet seat. Under the covers, you will find metal bolts that secure the toilet bowl on the floor. Loosen these bolts with a wrench and remove them.

Step 2-Dismantling the toilet flange
It is best to seek help from another person at this time to hold and lift the toilet bowl. Sometimes, the toilet bowl is not properly secured on its base and loosening the flange can cause it to fall off suddenly. Spread some old rags around the base of the toilet before attempting to tilt the toilet bowl. Ask your assistant to slowly tilt the toilet bowl. This could also cause a small waste of water retained in the toilet flush outlet along with traces of dirt for which the rags are made. This should reveal the flange bolt with the nuts that accompany it. The flange is a durable accessory, necessary to secure the toilet bowl in the underlying drain hole. The flanges are made of different materials, including cast iron and plastic. Metal flanges are difficult to handle as they can corrode. Use a sharp end of a screwdriver to remove rust. Use a wrench to loosen the nut and remove the bolt.

Step 3-Replace the toilet seal
It is best not to remove the toilet bowl, as adjusting it again could be difficult. Ask him to partner to keep the toilet bowl tilted as he goes through the repair. Using a spatula, edge the old wax ring. Replace it with the new wax ring. The seal of the wax ring should be adjusted. The new wax rings tend to protrude a little, which could damage the tight fit. Therefore, press down repeatedly on the seal. Now move towards the insertion of the flange bolts. Use a wrench to tighten the bolts.

Step 4: repair of the toilet board
Ask your associate to gently place the toilet bowl in its original position. Doing this with a tug can break the underlying ceramic tiles of the bathroom floor. Insert the metal bolts to secure the toilet bowl on the floor and tighten them with a wrench. Replace the plastic caps that you had removed at the beginning of the project. Finally, apply a thin layer of putty around the base of the toilet for a tighter fit.

How to wash the toilet? How can I clean a toilet?

How to wash the toilet? How can I clean a toilet?

To wash the bath Cup it is recommended to perform the following steps:

Toilet Bowl Ring Remove Product

1. Pull the handle from the TOILET and let the water run clean.


Como puedo limpiar bien un inodoro2. If using any product, apply and let stand for the time indicated on the label.


3. Brush very well, even on the water discharge flange and around the inside sides.


4. Let the water run again, and rinse the brush at the same time, shake very well and put it back in its base.


5. If the scale cannot be removed, apply muriatic acid (in half a bucket of water, two cups of acid and size with a broom or toilet brush), if you do not want to use the acid, tállela with a moistened water sandpaper.

Leaks in the toilet

Leaks in the toilet

Leaks on the outside of the toilet are easy to detect, but to solve them often it is necessary to dismantle the sanitary

Leaks on the outside of the toilet can cause significant damage and seepage across the floor. The advantage in this case is that water losses are easily detected. Sometimes problems are recorded in the area that joins the cup with the ground. Other times, leakages originate from watertight gaskets in poor condition. In many of these cases, it is necessary to dismantle the toilet or cistern to make repairs.

Toilet Bowl Ring Remove Product

 Problems between the toilet and the cistern

In order to solve the problems of water loss between the toilet and the cistern, it is often necessary to dismantle the latter to replace the sealing gasket and sometimes it is also possible to remove the fixing screws and the mechanism of the cistern. You have to take note of the deposit mark to buy a kit with all the necessary elements for the repair.

Then, the foam gasket is removed that allows the watertightness between the toilet and the cistern, the edges of the hole are cleaned to remove the lime scale and the new mechanism is inserted into the cistern. On the outside, the PVC nut is placed on the thread and locked to compress the gasket. Finally, a new foam gasket is installed on the nut and, again, the cistern on the toilet.

Leaks in the evacuation tube gasket

When leaks are recorded between the evacuation tube and the toilet, the latter must be disassembled. To do this, close the water stopcock, empty the cistern and disconnect the water inlet pipe to the cistern. Then it is separated from the wall and the clamping brackets are removed. To release the toilet from the floor, remove the screws that fix it. After unscrewing them, the toilet is carefully balanced to loosen the adhesive that binds it to the pavement.

    When leaks are recorded between the evacuation tube and the toilet, the latter must be dismantled

Sometimes the solution is to replace the seal gasket. In this case, after removing the toilet, remove the damaged gasket and cut the adjustment ring with a hacksaw. A new ring and elastomer gasket are then placed in place. Finally, just pull the ring to immobilize it in the neck of the tube and place the toilet in place.

Leaks in the bottom of the toilet

As time passes, water leaks can be recorded through the bottom of the toilet. Sometimes the escape is so scarce that it is barely noticeable. It may occur that the seal that joins the Cup with the floor has worn out and that this causes small puddles of water around the toilet.

To avoid the formation of moisture, fill this gasket with silicone or plumber's putty. This last product has a yellowish color that can be somewhat tarnished, so it can be painted with the same paint that is used to coat the joints of the tiles.

5 tips to eliminate lime: the best products

5 tips to eliminate lime: the best products

Lime can be a nightmare: it accumulates in the washing machine, in the taps or in our bathroom. Discover how to restore the brightness of your home.

Toilet Bowl Ring Remove Product

There are many ways to end the lime, however, we recommend the use of specialized products; There are different brands and different uses for these products: to remove lime from household appliances such as the washing machine, to leave our taps gleaming, or to finish with lime in the bathroom.

We tell you 5 tips to remove the lime permanently and we recommend the best anti-cal products on the market according to their quality-price.

Why lime is formed

Water often accumulates in cracks: between the tiles, the tiles, the faucets, the washing machine ... This water evaporates, however, its mineral residues remain.

The gradual accumulation of these mineral residues is what we call lime, which, in addition to being an accumulation of waste, offers a non-aesthetic appearance (a whitish layer that removes all shine from our tiles, sinks and appliances).

We will share with you some very useful tricks to eliminate lime in different areas of the house.

How to remove lime from the bathroom

In the toilet many bacteria are produced, therefore, a thorough cleaning every week is the best way to keep your bath hygienic and clean.

In addition to cleaning the toilet with your cleaning products, be sure to apply an anti-scale product inside the toilet bowl. Spray it with an anti-limescale product and let it act for 10 minutes. After that time, pull the chain and the water will clean the remains of the product.

Do this once a week, and if necessary, rub with the brush in the recesses in which a more visible amount of lime accumulates (once the anti-scale product has been applied).

As for the tiles, there is also the lime accumulates: being between the slits of the tiles, you must carefully apply the anti-lime product with a sponge or scrubbing pad; Leave the product to act for 5 minutes and rinse the remains of the antical with a wet cloth. Do not forget to dry the area when finished! We do not want to accumulate humidity!

How to remove lime from the tap

Removing lime from faucets requires more time; therefore, try to apply the product in a time zone in which you do not need to use that tap frequently, since you have to let the antical act for a long time (sometimes, depending on the amount of lime, can last for hours ).

To remove the lime from the tap and restore its original shine, soak a cloth of anti-scale product and wrap it with the tap in question. Another option is to rub the tap with the cloth, but in both cases it is necessary not to rinse the tap with water until after a while. If you wrap the tap with the cloth, do not remove it until after the actuation time.

With the shower head the procedure is the same, however, in this case it is advisable to disassemble the artichoke in order to reach all the nooks and crannies.

In all these cases, after time, rinse with water and dry carefully with a dry cloth.

How to remove lime from the washing machine

Cleaning the washing machine regularly is a guarantee of a longer service life and a better washing of your clothes.

Every so often (2 months, for example), fill the hot water washer and add one liter of anti-lime or bleach product to the dispenser.

With an operation as simple as this we make sure to keep our washing machine in perfect condition and a much longer durability. In the long run it means savings!

Better anti-lime products

The time has come for us to ask ourselves the big question: what is the best anti-calculus product? Which to choose?

Surely you already know some brands. We are going to recommend the brands with which we work, since, we believe, they are the highest quality for their optimal results and their effectiveness.

• -Calgon (gel)
• -Diranzio Bellido (anti-scale package for the lavavadora)
• -Codina (antical descaler)
• -KH7 (anti-scale gun)
• -Viakal (boat)
• -Viakal (spray)

Other options: salpumánico acid and phosphoric acid

There is the option to use acids to descale lime from certain areas, however, we recommend applying it with great caution, preferably by a professional.

The most commonly used acids are salpumánic acid (salfumán) and phosphoric acid. We recommend you learn how to apply them correctly before putting yourself to it for your safety and a more optimal result.

Have these tips been useful? Give us your opinion, and do not forget to tell us some other advice that you know and that we have overlooked :)

Come back to enjoy the original shine of your faucets, washing machine and bathrooms!

Toilet bowl top-features stripping

Toilet bowl top-features stripping

The problems in the toilet flushing system are not uncommon, however you can always fix them yourself, all you will need to remove the tank cap. Dismantling should be done carefully, as it may break or break. Therefore, in this article we will see how to remove the lid of a different type of toilet.

Toilet Bowl Ring Remove Product

General Information

In older models of drainage tanks, it is usually quite easy to remove the panel, simply unscrew the top of the trigger and lift it up. In modern tanks there is a drain button and a glass button, whose design prevents the dismantling of the cover.

However, in any case, this design is foldable, so this operation should not cause any special problem. The main thing is to do any action with care, without putting an excessive effort and slowly.

Before opening the toilet cistern cover, you must prepare some tools that may be necessary in the working process:

•     Pliers
•     Knife
•     Screwdriver

    Pay attention during operation with the tank, the water must be blocked. Otherwise, it can overflow and flood the bathroom.

Cover removal

At the beginning, it should be said that the lids of some models of modern ceramic containers are removed very simply, as the drain button is not connected to the trigger mechanism. To verify this, we must carefully try to lift the detail.

The following are ways to remove panels from other common types of tank designs:

•     If the water is drained as a result of raising the thrust, then before removing the toilet cistern cover, it is necessary to unscrew the ball located at the end of the handle.
•     Disassembling the container with drain buttons causes greater complexity, however, these models have become more popular recently. In this case, before opening the cover of the toilet cistern, you must unscrew the tube, inside which there are buttons. On the outside, it usually represents a ring, which must be pushed with a screwdriver or knife and turned counterclockwise.

It should be said that after this the panel cannot be completely removed, it can only be lifted and rotated a little, after which the latches of the button mechanism must be unfastened.

    The plastic tanks of the Soviet model, which are sometimes found in the apartments, have poles that must be removed before dismantling the structure with their own hands.


After the workpiece is disassembled, it must be placed in a safe place where it is impossible to hook and break it.

    Tip After repairing the toilet cistern drain attachment, it must be checked several times to operate. In particular, you must ensure that after lifting the float, the valve completely locks the water.

Cover Repair
Link

If in the dismantling process, something went wrong or the cover was broken for some reason, you can try to restore it.

For this you need to prepare the following materials:

•     Scottish
•     Epoxy adhesive;
•     Small galvanized steel plates.

The instructions for the implementation of this work are as follows:

•     First, all individual parts should be assembled in a single frame and taped. This should be done carefully so that there are no spaces where the glue can flow. To do this, all joints must be carefully taped.
•     Then the assembled structure should turn around.
•     Before gluing the toilet cistern cover, mix the glue with the hardener in a proportion of 1:10.
•     All gaskets should be carefully stained with glue and the galvanized plates must be attached from above, which will cause the product to become stiff.
•     When the glue hardens (about a day), the tape should be removed, after which the lid is installed in the toilet bowl.

Since the price of a new toilet is very high, this procedure will allow you to avoid the unplanned spending of family budget funds, while the appearance of the pipelines will not be affected.

Hole Increase

Often, home craftsmen, after replacing the drain fittings, face a difficulty: the diameter of the hole in the cap is smaller than the diameter of the reinforcement. Of course, you should not change the plumbing fixture completely, but how to increase the hole in the toilet bowl lid?

There are two ways to solve the problem:

•     Carefully drill the hole with a ceramic drill and cut out the remaining areas. The irregularities will be hidden by the cover.
•     Carefully chop the enamel with a thin drill and a hammer, then widen the hole with a round file.

In both cases, it is necessary to take great care not to divide the surface, because in this case it will be much harder to make a tank lid from the toilet bowl.

Here, perhaps, are all the main points you need to know to remove the tank cap and, if necessary, repair it.

Conclusion

The cistern cover of the toilet bowl, regardless of the type of construction of the latter, is removed quite easily. The main thing is to understand immediately what elements should be dismantled and not to make excessive efforts during work (see also the article: a toilet flush tank).

The video in this article will give you the opportunity to get additional information on this topic.

Installing a toilet

Installing a toilet

Installing a toilet is not a thing of the other world, just follow these simple steps, have a little patience and very careful and can do it easily.

Toilet Bowl Ring Remove Product

I imagine that you have the same thing happened to me once, we do an enlargement at home, for example an office, and logically we must have the toilets nearby so we do not have to cross the whole house, the ceramics are installed and then we call the Plumber , and oh surprise when we pass the bill to install a simple sink or a toilet charge us almost as we cost the same and of course no return to give we have to pay. Well, I started thinking about this matter when I finished the first bathroom of my house and decided to investigate how it is done, such a surprise when I realized that the work is as simple as "taking candy from a child" (if you please do not do that to children) , it requires that if enough patience and care.

Installing a toilet :

The first step is to acquire the toilet, do not think that they should go to the accessory store and buy the first one that comes or I like, this seemingly simple process has its complications and secret tricks; One is that they should consider saving the liquid element (for things like ecology), water is a precious and expensive, please ask them to buy toilets of 6 liters maximum, currently ay one piece models with this design; On the other hand and as more important step should consider the distance between the wall plated with majolica and the center of the sanitary outlet hole of four inches (or three if the case, although this measure is not highly recommended because it is prone to atoros) This distance should be at least 30.5 cms or 12 inches; Also the height of the outgoing drain pipe must be at least 1 cm. In relation to the finished ceramic floor . These considerations are important because not all toilets have the same measure; A variation in this matter would determine a bad fit of the sealing ring and the consequent leakage of water or annoying smells.

The good thing about acquiring modern toilets is that it already comes with the pre-installed internal accessories (for us as Bricómanos this is very convenient); Of course we must acquire other things like the water supply tube, this implement comes in several presentations: economical, usually with thread in ABS plastic and metal braided thread body less durable and I call premium, with Chrome-plated brass thread, aluminium braided body and inner reinforcement The thread size of this fixture must be 7/8 inch. We also have to supply two anchor bolts, these bolts are made of bronze and are instead of head with a removable nut to facilitate the fitting of the toilet base. A wax ring is the last implement for our project, this consists of a ring made of raw paraffin that in some presentations comes with a guide rubber that facilitates the fitting and installation (I recommend to buy in this type).

By hand all the above materials we proceed to install our toilet. A first step is to fit the toilet base into the drain hole, mark the places we drill with the drill (tip: use a 3/8 drill bit special for diamond-head cement, the hole must be previously Marked with a metal punch to avoid slipping of the bit), remove the base and perforate to insert the plastic anchors, the anchor bolts are screwed using a Stillson key (the movable head) or a self-pressure pliers (a tip: to mark the Hole location use indelible down, this if you paint on Majolica, the distance between the anchor bolts must be 16 cms. As a second step we turn the cup and fit the wax ring around the discharge hole at the bottom (tip: Do not place the toilet on the tile floor as it can chip, use the packing carton as Support). A third step is to fit the cup and adjust it with the nuts of the anchor bolts (A tip: they can "decorate" the head of the anchor bolts with ceramic plugs, sell them in the same health care provider and come in similar colors).


With the above steps we have already installed the toilet bowl or base, now we only need to fit the tank in place; To do this, simply turn the tank over and place the anti-leakage rubber that comes with the accessory kit and allow you to adjust the cup to the tank. The adjustment of the two parts of a toilet is carried out by the use OF ABS plastic regulating bolts (in modern toilets) or bronze (in the oldest), you should keep in mind that these bolts (which are placed from inside the tank) must go with their jebes to avoid leakage and in vertical position; Also be very careful in the placement of the tank, it must be positioned vertically and perfectly centered in relation to the cup (tip: Adjust the cup bolts by hand without using metal tools that can cause damage or breakage in them).

Good friends of "the housing market", we have installed our toilet, now we have to dispense with water, for this we taped with Teflon the supply tube in the part where the male thread and put a rubber inside the female thread; The male thread must first be placed in the water outlet of the wall (outlet usually ½ inch) once this is done adjust the thread on the outlet of the tank (tip: It is good to install a control key in case you miscarry a toilet accessory and cam is required Bio). Once all the above steps have been completed, seal around the cup with porcelain to make cleaning easier and prevent dirt buildup.

With these simple steps I believe without fear of mistaken that for you will be simple and gratifying to install a toilet, worth truths in these times always falls well save some pesetas and good there is no thing that makes us feel better than we do for ourselves.