Repair the toilet leak as an expert following these steps

Repair the toilet leak as an expert following these steps

Manos a la Obra now brings you this not very nice tutorial but necessary when things go wrong with our bathroom, especially with the toilet. Learn how to repair leaks with these steps; In the following image you will see the cross section of the toilet and you will notice common problems with water in the floor, water stains on the roof or an occasional smell of sewer gas are signs of a possible leak.

Toilet Bowl Ring Remove Product

Before pulling the toilet, pick up:

• A new wax ring
• Two 5/16 in. Sets Diameter of the water closet screws
• A silicone-based mastic tube, in a color to match the toilet
• A pack of plastic footwear for the bathroom if the toilet was swinging

Loosen the bolts

Unscrew the cabinet nut with a wrench. If the screw rotates together with the nut, grasp the exposed bolt over the nut with locking pliers. Loosen the nut enough to tighten a hacksaw blade under the nut and see through the bolt. TIP: Use a nearby metal saw as shown or wrap a rag around a bare blade.

Remove the toilet

Unscrew the nut that connects the water supply line to the bottom of the tank. Reach the inside of the tank with a long-handled screwdriver to hold the bolts while loosening the nuts underneath with a wrench. Lift the tank from the container, then lift the free container from the floor.

Clean around the drain hole

Fill a rag in the drain line to keep the sewer gases out of the house and pieces of wax from entering the pipe while cleaning. Scrape all the old wax off around the toilet horn and the toilet flange with a putty knife. Clean the floor under and around the old cauldron and debris toilet.

Prepare the new parts

Thoroughly clean the wax residue with mineral spirits. Place a reinforcement ring over the flange so that the grooves in the water cabinet bolt line up and mark the locations of the bolts on the floor. Drill a separation hole through the tile or masonry with a hammer drill and 1/4-in. Masonry Bit Stop when you reach the subfloor.

Apply caulking

Place a silicone cord around the perimeter of the toilet flange.

Screw the ring

Screw the ring on the floor, slide the water cabinet bolts into the slots and attach the nuts of the water cabinet with the nuts and washers of an extra set of bolts to the toilet flange. This will prevent the screws from tipping or wobbling while restarting the toilet. Scrape the excess putty and let the caulking cure during the night before you put the toilet.

Flange reinforcement rings

The flange reinforcement rings are essentially bandages that fit over the broken flange and bolt to the ground. They provide a new slot that receives the bolts from the toilet flange so that the toilet can be secured. You can find several styles in the store.

Prepare the extender ring

Clean the toilet flange with mineral spirits to remove all excess wax. Place the extension ring on the flange and remove the original flange bolts that align with those on the expansion ring. Apply a silicone caulk bead around the inside edge of the extender ring.

Screw the extender ring

Align the holes in the extension ring with the flange holes and screw both sides to the floor with 8 x 1-1 / 4 in. Stainless steel screws. Wipe off excess putty and restart the toilet

Remove the old flange

Remove the old screws from the toilet flange and slide each half of the flange bracket under the edges of the flange. Lift the flange with a screwdriver and lever if necessary.

Install the new wax ring

Push the new wax ring into the toilet's horn with the rounded side facing the toilet. Mark the positions of the water cabinet screw on the floor with adhesive tape.

Reinstall the toilet

Align the holes in the bolts with the adhesive tape and lower the toilet bowl directly onto the bolts. Push down on the rim of the toilet to seat the wax ring, then close the lid and sit on the toilet for a few minutes to force the toilet all the way to the floor. Stop when the porcelain surface rests on the finished floor.

Install wedges

Slide the bolt washer washers over the bolts, then tighten the washers and nuts of the water cabinet with a wrench. Be careful not to overtighten the nuts, especially on the separations between the toilet and the floor. Slide the toilet pads under any hole in the toilet rim and cut off the excess length. Some calzas are quite difficult. If a utility knife will not cut through the plastic, you may have to cut them off with a sharp wooden chisel.

Apply caulking

Heat around the base of the toilet with silicone putty, leaving the back end of the base. The gap leaves a space for moisture under the toilet to escape.

HOME AND GARDEN: How to remove tartar stains from the toilet

HOME AND GARDEN: How to remove tartar stains from the toilet

How to remove lime stains from the toilet bowl If the water in your home is hard, you will notice a rough, whitish substance in your toilet bowl. This is accumulation of lime. The scale of lime results from the remaining deposits of hard water. The buildup of lime scale on the toilet bowl makes the toilet dirty and stained.

Toilet Bowl Ring Remove Product

You can remove lime scale from the toilet bowl with common household items.

You will need to

• Toilet cleaner
• Brush to clean the toilet
• pail
• Water
• 1 gallon (3.78 l) of white vinegar
• Paper towels
• Borax powder

Instructions

1. Remove as much water as possible from the toilet bowl. Close the valve behind the toilet to stop the flow of water. Pull the chain a couple of times until the cup is empty.
2. Clean the inside of the toilet bowl with toilet cleaner. Apply a generous amount of cleaner and scrub the bowl with the toilet brush. This will make part of the lime stains come out but it probably will not remove everything. Throw a bucket of clean water into the bowl to rinse the cleaner.
3. Throw 1 gallon (3.78 l) of white vinegar into the toilet bowl. If this is not enough to cover all the lime deposits, wet paper towels and vinegar and place them on the lime stains. Leave the vinegar in the toilet bowl all night.
4. The next day, remove the paper towels. Use the brush to clean toilets and skirmish to remove lime deposits that have become loose. Clean the toilet by throwing a bucket of water into the toilet bowl. Inspect the toilet bowl to see if there is any lime stain.
5. Use borax powder if the spots do not come out. Spray a good amount of borax directly on the affected areas of the toilet bowl. Leave it for 30 minutes and then scrub with the toilet brush. Rinse the cup with a bucket or two of water.

Tips and warnings

1. Chlorine bleach can also be used to remove limescale. Pour 1/2 cup of bleach into the toilet bowl or soak paper towels in bleach and place them on top of the lime stains. Leave the product on the spots several hours before scrubbing the cup and rinse it with water.
2. Do not forget to reopen the water valve when you have finished cleaning.
3. Use a toothbrush to clean toilets that has plastic bristles so the cup does not get scratched.
4. Use rubber gloves when using bleach to protect your skin.
5. Never mix chlorine bleach with ammonia or products that contain these ingredients since the result can be toxic.

How to remove the dark circle around the toilet bowl OTHER METHOD

You will need to

• 12 oz (354 ml) of cola drink
• A brush for toilet
• 1 cup of white vinegar
• Sodium bicarbonate

Instructions

1-The tail effectively removes stains from the toilet.
Pour 12 oz (354 ml) of glue into the stained toilet bowl and clean it in circles with a bath brush. Leave the glue in the toilet water for an hour to remove the mineral stains.

2-Unload the toilet to wash the glue and loosen the brown rings and spots. Scrub the sides to remove mineral deposits removed by the tail.

3-Add 1 cup of white vinegar to the toilet water to dissolve the rest of the stains. Sprinkle baking soda over the brush to add a mild abrasive.

4-The scraping action of the toilet brush helps in the cleaning process.

Rub the surface of the toilet bowl with the brush covered in baking soda to remove the remaining stains. Discharge the toilet to rinse the surface.

Tips and warnings

• Add 1 cup of white vinegar to the toilet bowl every week and let it sit overnight to remove stains and freshen the toilet bowl.
• Substitute for lemon juice to remove spots of lime deposits and minerals inside the toilet.

How to eliminate brown mold in the toilet

You will need to

•  Whitening tablets for bathrooms
• Rubber gloves
• A bathroom brush
• A toilet cleaner
• 1 gallon (3.78 liters) of bleach

Instructions

1- Collect the elements that will help you clean. Any supermarket or pharmacy will have what you need.

2 - Pre-treat the toilet for an entire night. Brown mold usually gets together and grows in the pores, which makes it harder to remove. The best method to pre-treat mold is to wash the toilet. Pour half a gallon (1.89 liters) of bleach into the toilet and into the upper water tank and let it work overnight. Do not use the bathroom or throw the chain while you are following this treatment. Let it settle for at least eight to 10 hours or more. Make sure you close the toilet lid and the bathroom door, so your pets can not enter. Also, if you have a fan inside the room, turn it on so you can run more air.

3 - Flush the toilet. Put on rubber gloves and apply a generous amount of toilet cleaner. Scrub until you have removed all the mold left. The bleach will kill the most part and then the circular movements that you will make with the brush will take care of the rest.

4- Pull the chain several times until all chemicals are gone.

5- Treat the toilet again and scrub if necessary. Follow steps two and three.

6-Add a chlorine tablet to the toilet and water tank to prevent mold from returning.

Tips and warnings

It may take several applications of bleach and scrubbing sessions to remove and eliminate brown mold.
Always wear rubber gloves as protection when dealing with industrial-grade chemicals.

Natural products to remove scale from a toilet

White vinegar

White vinegar is a common product used to remove tartar from bathroom surfaces, including the inside of the toilet bowl, because white vinegar is a weak acid that will work by removing hard, alkaline water and stains from debris. of soap. It is not toxic and is completely natural. White vinegar also kills bacteria and other contaminants. To use, add 1 cup of white vinegar to the water in the toilet bowl. Leave to rest during the night before scrubbing the tartar and pull the chain. As an alternative, remove all the water from the toilet bowl and cover the tartar with cloth soaked in white vinegar.

Lemon juice

Another mild acid that dissolves the mineral deposits from the residue of hard water or soap scum is lemon juice. To use it, empty the toilet and apply the lemon juice to the tartar. Let it rest for at least 30 minutes before scrubbing the tartar with a bath brush. Rinse the area by pulling on the chain. Lemon juice will not harm porcelain or fiberglass toilets.

Pumice

Pumice stone is a natural stone that is abrasive and strong enough to remove scale from the toilet without scratching it. To use it, submerge the pumice stone in water so that it softens a little. Never use a dry pumice stone, as it can scratch the toilet. Rub the tartar stains until they run out. Rewet the stone as often as necessary to keep it moist while you work. Rinse the area with clean water.

Tartar prevention

Tartar will develop naturally in the toilet because hard water minerals accumulate on the surface. Soap residue could also accumulate and contribute to tartar stains. Prevent tartar by installing a water softener in your home. Also, scrub the toilet every week to eliminate the minute buildup and make sure the buildup does not reach a point where it is difficult to remove.

Do you hate cleaning the toilet? This trick will make your life a LOT easier... AWESOME!

Do you hate cleaning the toilet? This trick will make your life a LOT easier... AWESOME!

When it comes to keeping my house clean, I'm honestly not the best. And what's the worst place to clean up? The toilet. I don't even want to think about the amount and variety of bacteria that must be hidden there.

Toilet Bowl Ring Remove Product

Just thinking is getting close to cleaning gives me a lot of disgust. But here is a DIY diy trick very good to be able to clean the toilet easily and in a very fun way. [googlead] You have to mix several ingredients and let them dry in a mold to create very effective and cheap cleaning pumps to clean the toilet. Just one goal in the toilet you will see how magic happens... it's great! Watch the video below to learn how to create them.

Here's what you'll need

• 1/2 Cup sodium bicarbonate
• 1/2 Cup Citric acid
• Essential Oils
• Spray Bottle with water (optional, for spraying essential oils)
• Molds

How to fix a water leak from the toilet tank

How to fix a water leak from the toilet tank

Fixing a toilet is perhaps one of the things that no one wants to deal with. It is one of the reasons why many people prefer to rent, and one of the strongest arguments against renting properties (being a landlord) that are read on the Internet. I agree with both.

Toilet Bowl Ring Remove Product

Unfortunately, I had to deal with the problem a few days ago. And in fact, it's not the first time it's happened, it's part of owning.

When it comes to water leakage, I do my best to fix them as soon as I can. A water pot, no matter how small, can become your worst nightmare, as it not only has the potential to cause damage to your property, but it can also lead to health problems, hygiene and even your personal safety.

Immediately I noticed the water-pot, I began to work on it. Fortunately, the water leaks in the toilet, especially if it's the tank screws, are pretty easy to fix. Let me show you how to do it.

FIXING A WATER LEAK IN THE TOILET

There are several parts where a toilet can lose water:

•     The base (I hope it's not your case)
•     The main water connection
•     The gasket/connection between the tank and the Cup
•     The screws holding the tank

All cases are pretty easy to fix. However, the first requires completely removing the toilet to replace the wax ring, so it takes longer than everyone else.

If the leak is in the main water connection, you must inspect the hose as well as the (normally plastic) connection to the toilet, and replace if necessary.

The other two types of leakage are the ones I show you in this article.

HOW TO FIX A WATER LEAK FROM THE TOILET TANK

Before you begin to fix the water leak from the toilet tank, make sure you have all the parts and tools you need, then proceed to step 1.

•     Screwdrivers and hand tools (always useful)
•     Gloves and sponge
•     Toilet Repair Kit

STEP 1: INSPECT THE AREA AND DETERMINE WHERE THE LEAK IS

In my case, before I could determine that the toilet had a leak through the tank screws, I had to inspect it. As I said before, there are several parts where a toilet can lose water. Be sure to check thoroughly before starting the repair.

Leaks in the base or main water connection should be easier to identify. However, if you look closely between the tank and the cup, you must be able to see or feel the water between them. Take your time as this step is necessary to determine what tools or parts you need to fix it.

Once you have checked that the leak is between the tank and the cup, or much better, specifically by the screws that hold the tank, you can buy a toilet repair kit.

STEP 2: CLOSE THE MAIN WATER VALVE, DISCHARGE THE TOILET, EMPTY THE TANK

To complete this repair it is necessary to remove the tank from the toilet. Before you can do it, it's a very good idea to make sure it's completely empty.

To do this, you must close the main water valve, unload the toilet, and then use a sponge to get the rest of the water out of the tank.

STEP 3: DISCONNECT MAIN WATER INLET

Once the tank is completely empty, you can disconnect the water supply. Some of them may be removed by hand, others may require the use of a small wrench or pliers. When doing this, a small amount of water may come out of the tube and fill valve.

Disconnecting the main water inlet

STEP 4: REMOVE THE TANK AND SCREWS TO BE REPLACED

Using the same wrench or pliers, remove the nuts holding the tank in place. They should not be too tight, as it is not recommended to tighten them too much to avoid breaking the tank or the porcelain base.

If the screws start to rotate, you will need a screwdriver to hold them inside the tank. If the head of the screws is too corroded, you may need another pliers to hold them while turning the nut.

Removing the screws holding the tank

Once removed, place the tank over the toilet or somewhere else where it is easy to work on.

STEP 5: REPLACE THE GASKET BETWEEN THE TANK AND THE CUP – ANOTHER WAY TO FIX A WATER LEAK BETWEEN THE TANK AND THE CUP

This step can be considered optional, but I recommend you do it, even if the leak is not through this packing.

Since you've removed the tank, it makes sense to take advantage and do it. I would not want to repair the leak of the screws and a few days later having to remove the tank to repair another leak through this packing. I'm sure you don't either.

Removing the old packing to replace it with a new

Installing the new gasket in the tank

New gasket in toilet tank

STEP 6: INSTALL NEW SCREWS, GASKETS, WASHERS AND NUTS

Toilet Repair Kit instructions indicate that you must use the screw, washer and gasket inside the tank. Then, on the side of the Cup, another gasket, washer and nut.

For me it makes no sense to use a gasket on the side of the Cup, it is true that it could protect the porcelain, however, the idea is to avoid water leakage, so I decided to do it another way.

Since it had two additional washers and nuts of existing screws (you must also have them), not only I placed the washer and gasket inside the tank, but also placed another gasket and washer from the side outside the tank, and use the extra nut To fix them. In my opinion, two gaskets should work better than one.

New gasket and screws in toilet tank

New gaskets, screws and washers

Using the extra nuts to fix the gasket and washer

Then I used the other washers and nuts to hold the tank to the cup, as I describe in the next step.

STEP 7: REINSTALL TANK USING REMAINING WASHERS AND NUTS

As I described in the previous step, with the screws set, I reinstalled the tank and used the remaining washers and nuts to secure it. As I said before, do not overtighten the nuts, as this could break the tank, cup, or both.

Reinstalling the toilet tank

Using the pliers to tighten a little nut

STEP 8: RECONNECT MAIN WATER INLET

With the tank in place, you can proceed to reconnect the main water inlet. Do not overtighten as this may damage the thread of the fill tube (usually plastic) or cause leakage.

Reconnecting the main water inlet

STEP 9: OPEN THE WATER VALVE AND MAKE SURE THERE ARE NO LEAKS

Before you can think about your next project, open the water valve and make sure there are no leaks.

I recommend that you check the main water connection you just opened, the gasket between the tank and the cup and the screws that have just been replaced. Make adjustments if necessary.

Reader, have you ever had to deal with a water leak in the toilet? Where was the leak? Did you enjoy the experience?
Do you have a water leak from the toilet tank? Here's what you need to fix it:

•     Screwdrivers and hand tools (always useful)
•     Gloves and sponge
•     Toilet Repair Kit

How to change a toilet (removed and installed)

How to change a toilet (removed and installed)

How to Remove a Toilet

Your toilet can be removed in two stages: first the tank and then the toilet. The dirtiest part is to remove the old wax ring that is under the cup; When finishing this part, the work is easier. Before closing the water supply, make sure you have another toilet that you can use while it is not working. In addition, it is good to find out if your local garbage collection service collects old toilets or if you have to find a way to get rid of it. You do not want your toilet to become an object of permanent decoration in your garden.

Toilet Bowl Ring Remove Product

Step 1:

Close the valve that cuts off the flow of water from the supply line. Pull the toilet chain - this causes the tank and cup to empty - then remove the remaining water with a sponge. Disconnect both ends of the supply pipe, the stopcock and the toilet tank.

Step 2:

Use an adjustable or ratchet wrench to remove the nuts from the bolts that hold the tank to the bowl. There must be two or three, one on each side of the tank and possibly one in the middle. Carefully separate the tank from the cup and place it where it will not obstruct the passage.

Step 3:

If the floor screws still have lids, remove them and then remove the nuts from the floor bolts with an adjustable wrench. If the nuts do not yield, try spraying them with penetrating oil. If this does not work, you may have to cut the screws with a hacksaw or separate the nuts with a nut spacer.

Step 4:

Under the cup there is a wax ring that seals the bottom of the cup to the mounting flange, that is, the end part of the drain tube. To take off the seal you have to mount on the toilet and swing it gently from side to side. When the cup is loose, lift it up and then place it on one of its sides near you (but where it does not obstruct the passage).

Step 5:

Use a caulking spatula to remove the old wax ring from the mounting flange and bottom of the cup. Line a bucket with a plastic bag and place the old wax there. Clean the mounting base and bottom of the bowl with a stiff bristle brush.

Step 6:

At this time you will probably be smelling quite strong; they are mephitic drainage gases. To prevent gases from spreading in your home, put a rag in the drain hole. At the moment, you can cover the base and the cloth with an inverted bucket.


How to install a toilet

A new toilet is installed in two stages: first the toilet and then the tank. The most difficult part of the installation is to place the cup in its place, since it is heavy and has to be placed in such a way that the screws of the floor are directly aligned with the perforations of the base of the toilet. Once this part is finished, the most difficult part of the installation has been completed. When working with heavy porcelain items like toilets you should avoid hitting them against any object. Porcelain is resistant to a certain extent. If it is cracked it can not be used.

Step 1:

Put the new toilet bowl upside down and place a new wax ring around the toilet outlet horn. Press down firmly to adjust the ring. If the ring has a paper cover, remove it.

Step 2:

Make sure the base of the toilet is clean and that the floor screws are straight. If you had put a rag in the drain hole to avoid the mephitic gases, remove it. Then carefully place the toilet on its base and fit the perforations of the toilet base directly with the floor screws.

Step 3:

Press down the toilet bowl to compress the wax ring, so that it seals tightly. Attach the washers and nuts to the floor bolts and tighten them with an adjustable wrench. (Note: Do not tighten too much, the base may crack!) Install the screw caps.

Step 4:

You're already halfway there! Now follow the tank. In some tanks you will first have to install the lever, the float key and the discharge valve. Then put the tank upside down and place the rubber gasket over the outlet on the bottom of the tank.

Step 5:

Turn the tank over and place it over the toilet bowl, centering the rubber gasket in the opening of the water inlet of the cup near the back edge of the bowl.

Step 6:

You have to align the two or three holes in the bottom of the tank with the two or three holes in the top of the cup. Move the tank gently until you achieve your mission; Then put a rubber washer on each screw of the tank and insert the screws into the corresponding holes with the heads of the screws towards the inside of the tank.

Step 7:

From the bottom of the cup holds the washers and nuts to these screws. You can tighten them with a ratchet wrench until they are tight but remember, do not tighten them too much!

Step 8:

Cut a piece of supply tube to connect the stopcock and the toilet tank. First install the pipe to the stopcock and then to the float key of the cup. Tighten the connecting nuts of the joints with adjustable wrenches until they are snug. It can be easier if you hold the float key while tightening the connecting nut. Open the stop valve to fill the tank.

Step 9:

Your last task is to install the toilet seat. Place the seat screws in the toilet holes, screw the nuts into the seat screws and tighten them by hand. Note: toilet seats are usually not included with the toilet.

Removes stains from the toilet

Removes stains from the toilet

It is usual to observe brown spots on the toilet. These are generated by the presence of minerals present in the so-called hard water. The only problem is that when cleaning the bathroom, Removing the water marks inside the toilet is usually a delayed task.

Toilet Bowl Ring Remove Product

And of course, as with almost all the stains, the longer we let them settle on a surface, the harder it will be to remove them. So let's get to work: we're going to give you some tricks to remove the toilet stains .

Removing stains from the toilet

To proceed with cleaning, you must cut the water supply to the toilet and pull the chain so that the water level drops and you can act on the stains directly. It is also never too hard to use rubber gloves to clean.
Materials:

•     Sodium bicarbonate
•     White vinegar
•     Container
•     Toilet brush
•     Rubber gloves

Procedure:

•     You must prepare a mixture of baking soda and vinegar. To do this, put 2 cups of baking soda and add vinegar until you can make a paste.
•     Take the mixture and put it on the water stains. Let him act for about 10 minutes.
•     After that period, you must firmly brush the inside of the toilet. The action of the pasta soften the accumulation of minerals that form the stains.

Other tricks to clean the toilet

•     Borax is another great option to remove stains from the toilet. You just need to sprinkle the borax directly on the stains and scrub with the toilet brush. Leave to act for about 30 minutes and then pull the chain to say goodbye to the stains.
•     Trisodium phosphate is a substance that has been widely used in the manufacture of detergents. If you want to use it to clean the toilet, just dilute one tablespoon of this substance into 1 gallon of lukewarm water. Use a cloth to moisten it in the solution and scrub the stains until they disappear.

Well, with these tricks you no longer have excuses to remove stains from the toilet. Best of all, you don't have to do it with expensive chemical cleaners. By the way, I didn't mention it before, but you can use Cola soda to remove stains from the toilet; It is one of our practical tips for cleaning the bathroom and uncovering the pipes.

How to install a bathroom? Toilet Step by Step installation

How to install a bathroom? Toilet Step by Step installation

something that we should leave to the professionals.

This is partially true, if you don't have time then it's probably better idea to leave a professional plumber work. But if you have a little time and are willing to make a little effort in this House project, installing a bathroom is a great job to start for the first time with an installation.

Toilet Bowl Ring Remove Product

In fact you can have one installed in a few simple steps, that we will see then step by step.

What you will need

First of all, you will need to get the tools and materials ready before you start the installation process.

Most bathrooms come with all the pieces you need, in any case, you're going to require a toilet ring as well as 5/16 inch bolts to lock the toilet.

If you are replacing an old toilet with a new one, remove the former by cutting off the water supply and pulling the chain out, removing excess water with a bucket.

On the bottom of the tank exactly on the left side, you will find a nut that holds the water line to the ball key, you have to remove that.

You will also need to remove the two screws that block the toilet to the floor.

Once this is done, simply lift the toilet. On the floor you will notice a circular flange, this is where you are going to mount your new toilet.
Put the 5/16 inch bolts into the holes with the heads on the inside so they are straight and opposite each other. Place the new toilet ring on the flange with the flat side up.

Now just put the new toilet on the flange so that the bolts are in the right places.

Apply a little pressure so that the ring makes a seal to mount the toilet on the floor.

Hook-up time

The next part of the toilet installation is to tighten the screws with nuts and washers, but carefully (excessive adjustment will cause the bowl to wear). Just have the bolts to tighten firmly.

Now you have to install the cistern, you will have to push the mounting bolts at the bottom, as you did with the flange. In this case, you will have to place the rubber washers to ensure a perfect fit.

Place a rubber ring over the discharge tube (this is where the tank meets the Bowl). Make sure the ring is securely fastened and the bolts pass through the holes.

Tighten these bolts with the washers, get someone to hold the tank firmly down so you can screw tight.
Now what you need to put is one of the most important parts of the installation, the handle of the toilet, remember to turn the nut in the opposite direction, as it is a reverse thread.

Then connect the fin and chain to the inside of the tank. Once done, you are ready to attach the toilet cover to the cup.
There must be a water line ready to enter the bottom of the cistern, connect and then open the water. Keep an eye open for leaks, and then strip the chain several times.

If the container retains water without any problems, you are ready to screw the bowl to the ground. If there are still some shakes, you can use rubber wedges to stabilize things.

Once you have screwed the bowl, cut the ends of the bolts and put the plastic cap on them.

Putting a little putty around the base of the cup is also a good idea as it offers a shield and greater stability.

How to remove scale from the toilet

How to remove scale from the toilet

Scale stains are the most common stains on a toilet. If you have not Limpiás and noticed that the scale has accumulated in your toilet, this article will serve you. We give you a step-by-step guide to how to clean a cup of water with scale in an easy and effective way.

Toilet Bowl Ring Remove Product

How to clean a hard-to-scale toilet

The first thing we need to know before we get the scale of the toilets why the scale is formed. What causes the formation of tartar in the toilet is the accumulation of calcium and other minerals from the water. This creates yellow spots and brownish in our toilet. In areas with drinking water more scale is formed due to the concentration of minerals in the water. Don't worry, there are several ways to remove scale from the toilet.
How to clean the toilet scale

There are many natural products that can be used to remove the scale from the toilet, some of which we can have on hand. Revisá at home to see if you have any of these items and be used the cleaning method you want to remove scale from the toilet:

•     White vinegar and lemon juice. Mezclá in a bowl with sprinkler white vinegar and lemon juice in equal parts. Rociá the area of the toilet that has Tartar and let it act for 20 minutes. Then, with the help of a rag or sponge, quitá the scale; You'll see it's clear from the toilet without any problems.
•     Pumice Stone. This is a good solution if you do not know how to clean a cup of bathroom with Tartar. Humedecé a pumice stone with water until it softens slightly. Then pass the stone through the areas where it has scale, scrubbing carefully.
•     Sodium bicarbonate and soda cola. First echá a little soda cola over the scale stains on your toilet. Then cepillá the stains and let the tail act for half an hour. Finally, espolvoreá bicarbonate of sodium on the stains and rociá the toilet bowl with white vinegar: this will cause the tartar to soften. Finished the process, be back to brush to remove the tartar completely.
•     Sodium bicarbonate and oxygenated water. Mezclá ½ Cup of baking soda with 2 tablespoons of oxygenated water to form a paste. With a rag or grate, colocá the pasta in the toilet bowl. Let the mixture Act for 20 minutes and Enjuagá. The scale will go away easily.

How to remove scale from the toilet with a good product

While there are good homemade remedies to soften and remove the scale of the toilet, there are also good commercial cleaning products, such as the Bleach gel Vim, which eliminates 99% of germs and bacteria leaving your surfaces impeccable. I followed these steps:

•     Aplicá Vim Bleach in gel on the scale stains.
•     Let the product operate for 15 minutes.
•     With the help of a rag or sponge, retirá the scale of the toilet bowl.

It is important that you do a good cleaning of your toilet every 15 days to avoid the formation of tartar. Now you know how to get the scale of the white toilet and leave it shiny with the best tips!

How to install a toilet?

How to install a toilet?

Changing sanitary devices or placing a new ceramic can radically transform not only the appearance of the bathroom, but also the lifestyle of the one who uses it. So if your toilet is already worn, stained or broken, changing it can be an easy task to improve your environment.

Toilet Bowl Ring Remove Product

Tools to use:

• Bucket
• Concrete Drill
• Drill bit for ceramics
• Cross screwdriver
• Paddle tip Screwdriver
• Tape measure
• French key
• Pelican Key
• Caulking gun (for silicone)
• Electric drill

Materials to be used:

• Non-stick resin tape
• Silicone with fungicide
• Toilet
• WD40

 Before you start

Before removing the toilet, measure the distance between the back wall and the side screws at the base of the fixture, this will give you the measurement of the drain shaft on the floor.
With this measure choose your new device, selecting one that has the same axis or slightly larger.
Check all parts of your new toilet.

Parts List:

•     Cup and Pond
•     Anchor screws to Floor
•     Full Tank valve
•     Tank-to-cup coupling seal
•     Pond fixing bolts to cup
•     Discharge handle
•     Flexible Water
•     Wax drain ring with plastic, integral verse
•     Seat
•     Stopcock (optional)

1

Remove the existing toilet.

•     Drain the pond.
•     Close the Stopcock (also known as the angular key) so that it does not pass
•     More water.
•     If there is no stopcock for the pond, or else you want to change it, close the key
•     General step of the house and open some water faucets in other rooms
•     To drain the whole system.

•     Remove the toilet chain so that the water flows into the bowl. Should not enter
•     More water to the pond.
•     Put a bucket to receive the water and unscrew the existing flexible key
•     By the way.

•     Remove the anchor bolts from the cup.
•     Remove the pond from the Cup. This is not essential but it makes it easier to move.
•     If the nut is rusty and very tight, apply WD40 or similar product
•     to release it.

Recommendation

The toilets are heavy, take care of your back when lifting and moving.
DrainAlways try to use the same existing drain on the floor; Changing the position is complicated and quite demoro, and if the house has a single bathroom, it can become a real problem.
A change of drain implies-normally-more than a couple of working days: to break radieres or slabs, to cut existing pipes, to put a new section of pipe, to empty concrete again to close, etc.
And for all this it is advisable to hire specialists.

2

Install the new Cup

•     Present the cup with your pond and mark on the floor the location of the perforations for the new bolts.
•     If the location coincides with the above, remove the old anchors and put some new ones. Now, bolt the new.
•     If the perforations do not coincide, these holes must be filled with cement.
•     Once dry, drill two new holes with a ceramic bit.
•     Insert new plastic anchors.

Cup Position To ensure that the outlet hole in the bowl is perfectly centered on the drain pipe, do the following:

1. Once the old Cup is removed, mark the shafts of the drain pipe on the floor.
2. Put the new Cup back down and mark on its base the axles, extend
On the side faces.
3. Place the new cup by matching the marked shafts with the floor strokes.
4. Mark the contour of the workpiece on the floor and remove it.

3

Fit the wax ring

•     Put the cup, without the pond, legs up (inverted) and carefully resting on a carton so that it is not scratched.
•     Remove the protective cover from the wax ring.
•     Fit firmly into the bowl drain.

To level
Sometimes the ceramics on the floor are not well leveled.
If this happens, put plenty of silicone on the edge of the toilet base. This will help you level the position once it is set.

4

Seat Cup

   

•     Turn the cup carefully and lower it until the wax ring is perfectly aligned with the floor drain.
•     Press firmly into position.

   

•     Clean the silicone that comes out when you push the cup against the floor.

   

•     Screw the fixing bolts with their respective seals.

Installing pond Parts The inlet valve is installed with the separate 13 MMS float from the rear pond wall. The discharge valve is installed facing the discharge pipe.

5

Insert the inlet valve

•     Screw the float to the metal bar.
•     Insert the bar in the upper part of the valve and tighten in position by screwing.
•     Insert the valve into the corresponding hole in the pond, making sure it has the seal in place.
•     Notice that the float is separated from the walls of the pond.
•     With a pelican wrench secure the locking nut. Do not overtighten the account.

6

Insert the discharge valve

•     Insert the discharge valve into the central hole of the pond and with the locking nut secure it at the bottom.
•     The vertical overflow pipe must be oriented towards the inlet valve.
•     The top edge of the overflow pipe must be at least 13 MMS below the level of the handle perforation.

Recommendation

Be careful not to obstruct the placement of the two coupling bolts or the float bar.

7

Place coupling Seal

•     Place the coupling seal on the threaded end of the discharge valve, taking care to leave the tapered side down and the two bolt holes aligned.

8

Settling the pond

•     Install the pond on the bowl and match the coupling holes.

9

Connect the pond

•     Place the flat rubber washers to the bolts.
•     Insert them into the holes in the pond by placing the metal washers and nuts on the bottom.
•     Tighten the nut by hand, then hold it in place with a French spanner and tighten it from the top with a screwdriver.

10

Install the plug

•     Remove the protection from the underside of the flapper or stopper.
•     Connect in the indicated location to the discharge valve and the ears to the overflow pipe.

11

Install the discharge handle

•     Insert the discharge lever through the hole in the tank for the handle.
•     Secure with locking nut, turning counterclockwise.
•     The handle must be horizontal.
•     Connect the knurled banner of the plug to the discharge lever.
•     Adjust the length so that it rests completely on the discharge valve.

12

Insert the filling Hose

•     Insert the filling hose into the overflow tube.

13

Connect the Flexible

   

•     Connect the stopcock to the thread of the inlet key with a flexible toilet water supply.
•     Tighten with a French key without exaggeration.
•     Roll some non-stick resin tape into the thread of the nut or stopcock.

   

•     Open the stopcock.
•     The water level in the pond must be lower than the level of the overflow tube.
•     Regular with the screw at the top of the inlet valve, this will force the float to go down in the water.

14

Seal Cup

 Seal with silicone around the bottom edge of the bowl and floor.

How to remove scale from the bathroom with Coca Cola

How to remove scale from the bathroom with Coca Cola

The next time you stop for a Coke, make sure you have one for the house too. There are many things this soda can clean up in the house.

Toilet Bowl Ring Remove Product

Use Coca Cola as a bath cleaner

    6 ways you can clean with Coca Cola

•     What is good for removing stains from the toilet?
•     How to clean the bathroom with baking soda?
•     Tips on how to clean your bathroom effectively
•     How to clean your bathroom
•     How to unclog the toilet?
•     How to uncover a toilet without calling a plumber?
•     How to clean the toilet in the bathroom?
•     How to clean the bathroom in 10 minutes or less?
•     11 Amazing easy tips to clean your bathroom
•     Tips to clean your bathroom
•     Clean your bathroom with a product that is in the pantry of your kitchen
•     Tips for properly cleaning the bathroom

Some of them may even surprise you. Keep reading to find out exactly what you can clean a carbonated beverage.

Clean the 3 main articles of the Bath: the bath, the basin and the toilet.

Do you have hard water spots or ring around the toilet? Use Coca Cola and the toilet brush to remove the ring and allow the soda to rest for a while. Rinse when finished and have a toilet as good as new.

Desatascos madrid

For the sink and the bathtub, the Coca Cola breaks the layer and leaves them shiny. Pour directly over the area and wipe with a rag. It also helps to unclog your hair and dirt in your pipes as you go down.

Use in Greasy items:

Your husband has worked in the car all day and now his clothes are a greasy mess? What about that dish that the ham baked all day, now more greasy than your clothes? Use Coca Cola and allow items to rest, either in the washer or kitchen sink. The acid in a soda breaks the fat from the items and does not stain the clothes you are wearing.

You can also use Coca Cola in your vehicle. If the wiper fluid is not doing the work, stop and buy a Coke. Pour directly on the windshield and it will be in perfect condition.

Coca Cola is also a great way to remove all rust and corrosion from battery cables. Simply pour, let stand and observe how corrosion disappears, thanks to the acid of this wonderful beverage.

Use Coca Cola to clean

One of the active ingredients of Coca cola is phosphoric acid. It has a pH of 2.8, (on a scale of 1 -14, being 1 the most acid, 7 neutral and 14 very caustic). Pure phosphoric acid can eat through the metal and dissolve the concrete, but it certainly makes this drink taste good.

Rumors say Coca Cola distributors have used it over the years to clean the engines of their delivery trucks, and it also works to help remove dirt from the pavement of your windshield.

How to install two wax rings in a toilet

How to install two wax rings in a toilet

A leak in a toilet can be caused by things like a crack in the porcelain, a poor seal between the tank or a damaged inlet nozzle. If the toilet drips from under the base, the problem could be with the seal between the waste horn and the floor, which is sealed by a wax ring. In some installations where the toilet flange is lifted from the floor or the toilet waste horn design is unusually high, installing two wax rings can provide a more airtight seal, avoiding leaks under the toilet.

Toilet Bowl Ring Remove Product

• 1 Close the water supply valve behind the toilet. Unload the toilet to remove as much water as possible. Lift the lid off the back of the tank and remove all remaining water from the tank and toilet with a sponge.
• 2 Loosen the coupler that connects the supply line to the teat on the underside of the toilet tank using sliding joint pliers. Disconnect the supply line.
• 3 Remove the screw covers from the toilet base with a screwdriver. Place caps aside. Loosen the nuts on the mounting bolts using an adjustable wrench. Remove Washers. Lift the toilet bowl off the floor and place it sideways.
• 4 Scrape the old wax ring from the flange and the bottom of the waste horn into the base of the toilet using a spatula. Remove old bolts from floor flange cabinet. Insert a new set of cabinet bolts into the flange.
• 5 Place a wax ring over the floor flange. Align a second ring on the first and press down gently to begin molding The two wax rings together so that they do not get undone by placing the toilet in place.
• 6 Center The speaker on the toilet base over the wax rings and align the cabinet bolts with the mounting holes in the toilet base. Press the toilet, rocking the base slightly to seat the bowl against the rings.
• 7 Lift the toilet seat and place a level on the bowl. Slide a toilet wedge under the lower edges of the toilet base until the toilet is level in all directions. Place a washer over each cabinet bolt and tighten the nuts to the cabinet bolts with an adjustable wrench to secure the toilet. Replace Bolt caps.
• 8 Apply a drop of silicone putty around the base of the toilet to seal the floor base.
• 9 Connect the supply line coupler to the power nozzle on the bottom of the tank using the slide joint pliers. Open the water supply valve and test the toilet, observing leaks around the base.

Things you'll need

• Large sponge
• Sliding joint pliers
• Screwdriver Adjustable wrench
• Spatula Locker bolts with washers and nuts
• Two Wax bath rings
• Level
• Toilet wedges
• Silicone
• Putty

Tip

• A toilet is heavy, so you may want a wizard to help you place the bowl on the flange.

How to Change a Toilet Step by Step

How to Change a Toilet Step by Step

A noisy, leaky plumbing is not something you have to live with. Any owner with basic skills and tools can change a toilet and upgrade it to a new water-saving design.

Toilet Bowl Ring Remove Product

Installing a new toilet will take a couple of hours, but the reward will last for years.
Tools and Materials

•     Spatula
•     Adjustable wrench
•     Screwdriver
•     Spare toilet
•     Wax Ring
•     Toilet bolts
•     Silicone Caulking Putty

How to take steps for a new toilet

Make sure the new toilet is fitted to the previous place.

Measure from the wall behind the toilet to the center of one of the adjustment bolts (the bolts that hold the toilet to the floor). Do this before you take out the old toilet so you can buy a new one and have it handy before you start. If the toilet has four adjustment bolts, measure to the center of one of the back.

Also, measure from the center of the mounting holes to the back of the new toilet you have chosen. Compare these two measurements. If the base of the new toilet is shorter than the distance between the holes for the rear bolts and the wall, it should fit.

In small bathrooms where space is small, also measure from the sides of the flanged bolts to the side walls or other objects to make sure there is space between the sides. You don't want to find out after you start that you can't put the new toilet in place because you're trying to occupy part of the same space as your sink.
How to buy the toilet

Unless you buy one of the slim new models in one piece, you will have to buy the cup and tank. They'll come in two separate boxes. Virtually any tank you buy will have the discharge valve assembly installed, but it would not be too much to check.

In addition, you will need new adjustment bolts, a wax gasket and a toilet seat if they are not included. If you think about replacing the supply line, those that are flexible are coated in stainless steel mesh and are resistant, attractive and very practical. There are also cheaper plastic supply lines, in case you are worried about the price.
How to remove the old toilet

If you want to remove a toilet to change it, it will be better for your back, your floor and your walls if you retire it in pieces. Even if you remove the toilet, do not break it.

•     Cut off the toilet water supply. There must be a valve next to the tank that extends from the base of the wall or floor.
•     Pull the toilet chain and remove any remaining water from the tank, and from the bowl with a small cup and sponge.
•     If you plan to reuse the supply line, unplug it from the bowl. If you plan to replace the supply line, remove it from the supply valve and just leave it attached to the cup.
•     Remove the lid from the tank and place it on the floor, far away so that it does not interrupt, or better, in another room. Do not support this fragile piece against the wall near your workplace. If you fall or hit while trying to move heavy parts of the toilet, it is likely to break.
•     Remove tank from Cup. It will be set by a pair of bolts near the center of the cup where it is attached to the tank. These bolts pass from inside the tank through the mounting flange on the back of the cup. Simply remove the nuts and remove the cup from the gasket. If the bolts are rusty and the nuts are difficult to desenrroscar, wet the bolt assemblies for a few minutes with a lubricant. Place the tank in the most remote place possible, if it is out of the house better.
•     Remove the bolt covers from the toilet base and remove the adjustment bolts. Some toilets have four adjustment bolts that hold them to the floor. Most of them will have only two.
•     Move the cup to remove the wax gasket. Unless you want to bring the cup directly outside, have a piece of paper or plastic ready to place. The gasket will be dirty and sticky, and the wax of a cup gaskets is a difficult material to clean from any surface.
•     Cover the drain hole to prevent the fumes from escaping into the room. Do so that your stopper (cloth or other) does not fall down the drain and tape it.
•     Use a flexible spatula to sand the wax or putty from the Cup base and floor mounting flange.
•     Clean and level the installation surface before installing the new toilet.

How to repair damaged flanges

Toilets can be installed in two ways. The adjustment bolts may have flat heads, which are inserted into the slots in the flange. In this case, the cup is secured to the same flange; The flange serves as a toilet support.

The second class of adjustment bolts have screw type threads at one end and bolt thread on the other. These adjustment bolts hold the toilet directly to the floor. The flange in this type of installation acts only as a support for the wax gasket and does not support the cup clamping pressure.

Once you have removed the previous toilet, you may find that the flange on which it is installed is damaged. Flanges can be made of many materials, such as cast iron, copper, brass and plastic. If the flange is badly damaged, you can ask a plumber to replace it. If it is not too cracked or broken, you can make a simple and permanent repair with a special tab that is placed under the edge of the flange.

This tab has a hole through which the adjustment bolt is placed. After the bolt is inserted through the hole, the tab is placed under the flange edge on the broken part. When tightening the adjustment bolts, the tab presses against the underside of the flange edge, which holds the cup in place.

Of course, if the toilet is installed directly on the wood floor and not on the flange itself, the seat of the flange (the inner circle against which the wax will be sealed) is the important thing. If the flange is cracked or broken inside, you will need to replace it.
How to install the new toilet

Always refer to the manufacturer's instructions for the purchased model.
How to place the Cup

You can install a new toilet the same way you removed the old one, in pieces.

•     Insert the adjustment bolts if they are the type that are inserted into the flange and place them on a line parallel to the wall behind the toilet. If they are of the type that is screwed on the floor, place the new bolts in the place of the old ones.
•     Turn the bowl over the floor. Place something underneath (a rug or blanket) to prevent damage. Install the wax ring on the waste outlet with the tapered end facing the toilet. The debris outlet is the bump from the base of the toilet that extends to the flange. A hardened wax ring is softer and more malleable. If you bring your ring from the cold outside, allow it to heat before performing this step.
•     Disconnect the waste drain hole and place the toilet on the flange. Install the washers and retaining nut without tension. Make sure conical washers are installed with the right side up. These washers are labeled in the manufacturer's instructions.
•     Place the toilet and gently press down against the wax ring and the flange with an oscillating motion.
•     Once the cup is in place, tighten the nuts on the adjustment bolts, alternating side-to-side, so that the pressure is evenly distributed.
•     Install the bolt caps on the adjustment bolts. After the installation is complete and check for leaks, you can seal the toilet base with sealant. You can use silicone sealant for bath and Bath. It can be applied from the tube and straightened with a damp finger.

How to install the tank

•     Install the large rubber ring over the outlet on the tank base according to the manufacturer's instructions.
•     Insert the tank mounting bolts and rubber washers from the inside of the tank through the bowl mounting area.
•     Place the tank in place and tighten the nuts alternately until the tank is securely attached to the cup. Again, do not overtighten.
•     Install a toilet seat according to the manufacturer's instructions.
•     Install the water supply line. If you use the new flexible water supply line, this step is easy. If you use a rigid supply line, you will need to bend it a bit to fit it. Don't curling the line. This will clog the water flow and weaken the line, so it may break or drip.

How to adjust the discharge mechanism

After changing the toilet it will be necessary to verify its operation and it is possible to make some minor changes to the discharge mechanism. Try pulling the toilet chain to see if it works and if you need any change. Follow manufacturer's instructions.

Cleaning the toilet with hygiene and removing brown spots

Cleaning the toilet with hygiene and removing brown spots

The toilet of the bath is one of the places of the house that more germs and bacteria accumulates. In many homes, the toilet Cup attracts dirt constantly. Residues of urine or other types of waste require constant revision. Therefore, when it comes to cleaning bathrooms, we recommend that the toilet become the place that most attention lend.

Toilet Bowl Ring Remove Product

Clean restrooms and other cleaning products you should use

Rubber Gloves will be your best allies in this cleaning job. They will isolate your hands from germs, and turn the experience into something more enjoyable. To ensure the hygiene of the bathroom and clean the toilet properly, also has paper and some cloths, we recommend the microfiber. As a cleaning essential product choose the lye. Their hygiene and disinfection capacity are very high. If you also choose the one that is less harmful to the environment, the better. Finally, you also have a scouring pad, with the "Most of the dirty work" and you will be able to rub the surfaces OF the WC properly. Do not use those that are metallic. They will scratch the toilet and the cleaning won't be greater.

Cleaning the outside of the toilet

Since the part of the toilet with which our body takes more contact is the outside, it will be to which we devote a special care. First, rinse the scouring pad we will use in the lye . As commented above, we recommend those other than metal. Once rinsed, rub with the necessary force, starting from the lids to reach the sides and the top. Once everything is correctly soapy, we will pass to use microfiber cloths. With them moistened, we will make a second review all over the surface, removing the remains of lye that has left the scourer. The toilet should be damp, but not wet. To dry it completely, it is ideal to use newspaper papers.

How to clean the TOILET inside

For cleaning the inner part, look first at the amount of water in your toilet. If it is a lot, you will have to empty it, because in another case it is difficult to access some of the areas of the WC. You can do it by closing the key and pulling the chain. Lift all the lids, rub with the scourer on your inner face and proceed as you indicated you should do when cleaning the outside. Once you have climbed and soapy, you can take advantage of them while drying to clean the innermost part and remove the scale that accumulates. This, in addition to tarnishing the aesthetics of YOUR toilet, is very difficult to remove. We tell you some tricks to make it easier.

How to remove scale from the TOILET

To complete the cleaning and leave it spotless, we only have to clean the toilet with brown spots and clean the scale. Although there is a good range of alternatives, let's talk about one that cleans effectively and is completely natural: the formula of white vinegar and lemon.

White vinegar and lemon to clean the scale of the WC.

As we wrote in previous posts, the lemon is a potent natural disinfectant. Its combination with vinegar offers very good results. In addition to serving you to remove the scale naturally, the lemon fragrance will leave a smell less strong than other products that remove the scale. For cleaning, pour approximately half a glass of white vinegar combined witha lemon juice. With a different pad than the one used, vigorously rub the area of the toilet with tartar or brown spots. The results will surprise you.

You already have a complete guide to clean the bathroom toilet and all its parts. We hope you will put all these tips into practice. Soon, we'll talk about how to clean the bathroom tiles and increase their hygiene.

How to remove waste from the toilet

How to remove waste from the toilet
The residues of saltpeter are as disgusting and unpleasant as their name. Deposits can form where there is heavy water.

Toilet Bowl Ring Remove Product

When this happens, Scrubbing Bubbles® Power Stain destroyer Toilet Bowl Cleaner Fight against the accumulation of saltpeter. The green liquid turns blue as it falls.

Once you have cleaned it, you can keep the cleaning with the Scrubbing Bubbles® Fresh Gel Toilet Cleaning System. Just place a gel mark under the edge and achieve fresh cleaning every time you pull the lever. In this way, the waste of the saltpeter does not feel comfortable and disappears.

Whether there is hard water or not, the waste of saltpeter does not deserve to have the opportunity. Not while Scubby is in charge!

How to do it

•     Lift the toilet cover.
•     To remove the lid, press the two texturized side surfaces and unscrew completely.
•     Tilt the bottle to fill the beak.
•     To remove the waste from the nitrate and rust, apply the product to the toilet bowl and wait for 15 minutes to settle. In case of a large accumulation of waste from the nitrate or oxide, apply the product again and let it rest until the other day.
•     Brush the entire cup and pull the lever.
•     Cover the container and close it until you hear a "click".

In the case of stains that are difficult to remove, allow Scrubbing Bubbles® Power Stain destroyer Toilet Bowl Cleaner Act for a few minutes.

5 PRACTICAL TIPS ON HOW TO REMOVE SCALE FROM THE TOILET QUICKLY

5 PRACTICAL TIPS ON HOW TO REMOVE SCALE FROM THE TOILET QUICKLY

Eliminates the task of cleaning a toilet with these smart tips and tricks. Simple household products will help your bath shine, but with our cleaning shortcuts, the idea of how to remove the scale is much easier, avoiding the rings in them, in order to be comfortable with our toilet. Few jobs are not inducers to clean a toilet. Nobody wants to get close to their dresser, but it's a necessary task. We have developed some tricks for.

Toilet Bowl Ring Remove Product

Most of our tips require little or no contact with the actual toilet. They also put common household products into work, so it is not necessary to stock up on elegant cleaning products.

1
USE VODKA
Take that cheap bottle of vodka that has been occupying the cabinet space for too long and use it to make your bath shine. Pour 1/2 cup of vodka into the toilet bowl each month to prevent rings from forming.

2
POP IN DENTURE TABLETS
Rushed? For super-fast cleaning, place a tablet or two dentures in the toilet bowl. The effervescent action will provide a quick mini-cleaning in minutes, without the need to use a scale-removing brush.

3
Draft
Rushed? For super-fast cleaning, place a tablet or two dentures in the toilet bowl. The effervescent action will provide a quick mini-cleaning in minutes, without the need to use a scale-removing brush.

4
WATER WORKS
Pour a bucket of water into the toilet bowl before covering the inside with a cleaner.

This will empty the toilet without causing a filling of the bowl. The reduced water level allows you to place the cleaner directly into the toilet for deeper cleaning.

5
COVER WITH CLEANER
To expedite the cleaning process, cover the toilet bowl with cleaner before doing anything else.

Then continue with the handle, seat, tank and any other area you would like to disinfect. When finished, the toilet bowl cleaner will be soaked. Rub and clean.

Cleaning stone for lime in toilets

Cleaning stone for lime in toilets

The use of cleaning stone or pumice stone is not yet widespread for sanitary cleaning. And from ClimProfesional we want to show you the advantages of its use.

Toilet Bowl Ring Remove Product

It is often that in homes and offices or public toilets we find toilets where there are some dirty rings to the lime rings in toilet.

Lime rings in toilet

Water level height, and lime deposits embedded under water level.

Those deposits seem almost impossible to eliminate. And usually appear in toilets that are used less frequently and in areas where the water contains more lime.

Although there are specific anti-limescale cleaners, suitable to remove these remains, we want to offer you another ecological solution: the cleaning stone.

The cleaning stone is made of cellular glass and has a strong descaling acid power. If you haven't used it before, this stone has a similar effect to the pumice stone. Yes, that same stone used at home to remove the excess skin from the bottom of the foot as well as the hardness.

Why does the cleaning stone work?

The cleaning stone will not damage the brightness of your toilet.

It is a eco product manufactured with glass treated at high temperatures and with the latest technologies, in a process similar to that of nature in the formation of volcanic pumice.

They are manufactured in 100% glass, a harmless material for health, non-allergenic and environmentally friendly..

Cleaning Stone to remove limescale from the toilets. ClimProfesional.

How easy is it to remove the remains of lime?

Very easy.

Clean the scraps that are easy to remove using your regular bath cleaning product.

Empty the cistern and remove all the water left in the toilet.

Clean all the water with a cloth and rub the remaining lime residues with the ClimProfesional cleaning stone.

Or in its absence with a moistened pumice stone.

And ready!!! It'll be shiny for a while.

With the use and the passage of time will reappear those remains of lime. But we've already won the battle and we know how to leave the toilet as new very easily.

How to remove the blue rings from a toilet

How to remove the blue rings from a toilet

Blue rings in the toilet bowl are typically caused by mineral deposits that are present in the water. Copper is the common culprit of blue or greenish spots. These stains can make your toilet old and dirty. Fortunately, there is no need to live with these nasty-looking stains. With a few common household items and a bit of hard work, you can remove the blue rings and restore the look of the toilet bowl.

Toilet Bowl Ring Remove Product

Instructions

• Wash the toilet and allow the container to fill with clean water.

• Insert 2 to 3 cups of white vinegar into the toilet bowl. Clean the toilet bowl with vinegar/water mixture and a bath sponge. Let the vinegar stand for 20 minutes in the bowl.

• Scrub the toilet bowl once again with the water purifier mixing and cleaning. Wash the toilet and allow the container to fill with clean water.

• Add 2 cups of ammonia to the toilet bowl. Scrub the blue rings with the ammonia-water mixture and a bath sponge. Let the mixture sit in the cup for 15 minutes.

• Clean toilet Scrub with ammonia-water mixture and sponge. Continue scrubbing until the blue rings are no longer visible. If necessary, allow the ammonia-water mixture to remain for an extended period of time.

• Wash the toilet to rinse the cup. Let it fill with clean water.

• Clean the toilet weekly cup with white vinegar or a commercial toilet cleaner.

Tips and warnings

•     You can also drain as much water as possible and scrub the blue rings with a moistened pumice stone.
•     Never mix ammonia with bleach or bleach-containing products. The resulting fumes are toxic.

Removing calcium rings in Kohler toilets

Removing calcium rings in Kohler toilets

Normally, mild abrasive cleaners can clean the vitreous china from Kohler bath bowls. Strong cleaners will not only damage the surface, also remove the luster from the cup surface. Kohler reports using a stronger cleaner to cope with hard water deposits such as calcium rings that accumulate over time. Products such as Lysol bath cleaner are recommended by Kohler to clean the toilet, consider another Lysol product, or a similar product designed for hard water stains on the calcium ring.

Toilet Bowl Ring Remove Product

Instructions

• Shut off the Kohler toilet water by turning the shutoff valve behind the toilet completely to the right. Wash the toilet. The container does not fill with water, so the water level will be lower. Wash a second time to further reduce water.

• Lift the toilet seat. Apply a commercial cleaner that removes hard water deposits directly into the calcium ring inside the container. Cover the water line ring and the series of the rim holes above inside the bowl.

• Allow the cleanser to sit quiet for about 10 minutes. Leave the seat up during this time.

• Scrub the surface of the entire inner container, focusing on the holes in the rim and toward the calcium ring in the water line. Use a nylon brush to clean the bowl. Switch to a plastic bristle brush, if the nylon brush is not effective in washing the calcium rings.

• Twist the valve to the left and allow the tank to fill with water. Wash the toilet so the bowl cleaner is removed.

How to recover a wash ring in the toilet easy way

How to recover a wash ring in the toilet easy way

Losing a ring on the toilet can be a nightmare, especially if it's a relic, a souvenir or a symbol of your love. Once something is emptied into the toilet, it travels through the internal pipes of the bowl, through the pipes and sewer system or septic tank. If your ring is to pipes, the costs of ripping the pipes and septic tank will be much more than the cost of most jewelry pieces. However, if the ring is still in the toilet, there is hope. Removing the toilet is the only way to know for sure.

Toilet Bowl Ring Remove Product

Instructions

• Look behind your toilet and find the supply valve located on the water line that feeds the tank. Turn off the valve. Press and hold the lever in the tank to empty the toilet and empty the tank.

• Lift the toilet tank cover and put it aside. Place the nuts on the bottom of the toilet. Remove the nuts with the appropriate deep-well socket from the assembly. Reach into the tank and remove the retaining bolts. Lift the tank from the toilet bowl and put it aside.

• Look on the floor and find the dome-shaped plastic cap on both sides of the toilet bowl. Remove the plant covers using a flat-blade screwdriver and store them. Remove the retaining nuts by keeping the cup on the floor. Lift the toilet off the floor and place it next to you.

• Remove the nuts on the underside of the top edge of the toilet using the plastic tweezers. Pull the cup seat and reserve. Lift the toilet upside down with the help of an assistant. Shake the bath to see if the ring falls out of the jar.

• Turn the toilet bowl straight up and place it on top of a 5 gallon bucket. Spray water from a hose into the toilet bowl to try to remove the ring from the ins and outs of the toilet. Dump the bucket in the tub when necessary.

• Remove the old wax ring from the drain on the floor. Scrape the remains of the plant and the bottom of the vanity with a plastic putty knife. Clean the toilet and floor with a clean cloth. Place a new wax ring around the drain on the floor. Secure the toilet bowl at the top and replace the retaining nuts. Tighten the nuts with an outlet. Tighten plastic caps over bolts.

• Inspect the bottom of the tank to make sure the rubber is in its proper place. Back the tank over the toilet bowl. Slide the retaining bolts through the tank and bowl. Turn the nuts on the bolts. Tighten the nuts with an outlet. Place the seat on the bowl and secure with the plastic screws and nuts. Tighten the plastic nuts with their tweezers.

• Restore the water supply and see the toilet if there are leaks. Flush the toilet several times to check the wax ring. Clean the area with your VAC store rinse out the bucket and fill it with water. Add 1/2 Cup of bleach to water. Clean the bath, toilet and floor with a bleached water--soaked rag. Allow the bath to dry thoroughly before using again.

Tips and warnings

•     Gloves and safety goggles are required when using hand tools.
•     Rubber gloves and safety goggles are required when using bleach or other chemicals.

How to remove plaque from the toilet quickly and at home by 5 homemade tricks

How to remove plaque from the toilet quickly and at home by 5 homemade tricks

Discover five simple tricks to get an impeccable bathroom in just a few minutes

The toilet is one of the household elements that we use the most, which is why our goal is always to keep it clean, disinfected and free from bad odors . However, due to the accumulation of germs, moisture and other substances that make contact with its surface, it is common to have tartar stains.

Toilet Bowl Ring Remove Product

This problem is usually caused by the accumulation of calcium and other minerals present in the water supply. Fortunately, with the following 5 homemade tricks , you can remove tartar from your toilet and keep it impeccable.

1. White vinegar and lemon

The combination of white vinegar and lemon is the most natural and ecological way to eliminate tartar . It is quite useful since the natural acids of both liquids easily decompose tartar deposits. You will need & frac12; cup of white vinegar (125 ml) and lemon juice.

Add the lemon juice in half a cup of white vinegar and mix. Next, rub the mixture over the areas you wish to clean. To make your task easier, you can use a scouring pad or sandpaper.

2. Pumice

Pumice, although it is generally used to remove dead skin, is very useful for removing stains that form in the bathroom. Its abrasive power removes scale and leaves the surface with a more hygienic appearance.

All you have to do is submerge the stone in warm water , until it softens. You have to moisten it yes or yes since the dry stone can cause damage to the toilet. When the stone is soft, rub on the areas where you notice the presence of tartar and you will see how it is removed, leaving the toilet untouched. Rewet the stone whenever necessary.

3. Sodium bicarbonate with hydrogen peroxide

If you use this procedure you will only need & frac12; cup of baking soda (100 g) and two tablespoons of hydrogen peroxide (20 ml).

Moisten the sodium bicarbonate with the oxygenated water, obtaining a kind of paste. With the help of a cloth or sponge, rub the paste against the walls of the toilet to clean the stains. Let it act 20 minutes before rinsing it.

Optionally, you can add lemon juice to achieve a more powerful whitening effect.

Mix 100 grams of baking soda with two tablespoons of hydrogen peroxide. Source: Getty Images

4. Coca Cola

Coca-Cola compounds can help remove tartar and stains that form on the surface of the toilet, but to maximize its effect you must combine the soda with other products.

You will need: a can of Coca-Cola, a cup of white vinegar (250 ml) and three tablespoons of baking soda (30 g).

Having previously dried the toilet, pour Coca-Cola making sure to cover the areas where the tartar is. Let it act for 30 minutes and brush it. Then add the white vinegar and baking soda over the tartar stains. Wait for 15 minutes to act and rub the remaining scale with a brush. When you're finished, rinse the toilet.

5. Borax

It is a useful substance to disinfect and bleach the toilets of the home. It is a bit more aggressive than the previous ingredients, but does not cause strong impacts on the environment or leave volatile compounds harmful to health.

All you need is: a cup of white vinegar (250 ml), four tablespoons of borax powder (40 g) and one liter of hot water.

You have to sprinkle with white vinegar the surface of the bath and let it act 20 minutes. When the time passes, rub it with a brush and then add the tablespoons of borax. After another 15 seconds, add the liter of hot water and remove the impurities with the help of a sponge.

If you use this method, it is very important that you wear gloves and a mask to avoid accidents.

Borax will help disinfect and bleach the toilet.