TOTO CST784EF#01 Eco Clayton with Elongated Bowl, Cotton White

How to remove a tank from the toilet with a key

Sometimes it is better to use a pipe wrench to remove the toilet tank from your toilet due to the limited area in which to work. The toilet flange is molded in a way that prevents getting a good grip around the toilet cistern fixing nuts with a standard wrench. A pipe wrench works well in this case because the socket fits into the small area and the handle of the pipe wrench is far from the toilet flange, which allows it to turn the nut. Removing a toilet tank with a pipe wrench is still the same process as if you were using a standard wrench.



TOTO CST784EF#01 Eco Clayton with Elongated Bowl, Cotton White

Instructions

1 Close the water supply to the toilet. The water supply valve is behind the toilet between the house line that comes out of the wall and the line that goes to the bottom of the toilet cistern.

2 Remove the tank lid, and pull the chain. Keep the dump lever down until almost all the water is out of the tank. Absorb the remaining water in the tank with towels.

3 Turn the water line connector on the bottom of the toilet tank to the left by hand. If you have a plastic pipe or copper pipe as a water line, loosen the connecting nut with a wrench to disconnect the water line from the tank.

4 Place a large flat-blade screwdriver on the slotted head of one of the tank bolts inside the bottom of the tank. The heads of the tank bolts are near the discharge valve on the bottom of the tank.

5 Loosen the tank bolt nut below the tank with a socket wrench and socket. Do not allow the handle of the pipe wrench to strike against the outside of the toilet bowl when loosening the nut. Once the nut is loose, keep turning to the left with your fingers until it is out of the bolt.

6 Repeat for the remaining tank tank bolt. Once both nuts are out of the toilet tank bolts, lift the toilet tank.

Tips and warnings

•     Some manufacturers use three toilet tank bolts to secure the toilet tank.

American Standard 3483001.020 Cadet Right Height Elongated Universal Bowl in White

What is a toilet tank with insulation?

Insulated toilet cisterns provide a way to combat sweat baths, which commonly occur in areas with high temperatures and humidity. You can use a toilet with an insulated tank and not realize it, unless you know where to look for the insulation material. Insulating a toilet tank will help prevent serious damage, not only to the bathroom, but the structure of the house.



American Standard 3483001.020 Cadet Right Height Elongated Universal Bowl in White

The sweat baths

Toilet cisterns contain cold water, that is, the tank is also cold from contact with water. In areas that have hot, humid climates, tank sweats like hot, humid air come in contact with the cold toilet tank. The air condenses in the tank, creating sweat. If a house has a dehumidifier or air conditioner, the tank does not sweat much or nothing at all.

Potential water damage

As the water in the air condenses into the toilet tank more and more, the water mixes into larger droplets and starts running down the sides of the tank. The water droplets eventually drain off the toilet tank and fall to the ground. This accumulation of water leads to water damage to the floor of the bathroom, as well as the subfloor and the room below. The constant humidity from the sweat tank can also lead to the growth of mold in the bathroom.

The insulation kits

An isolation kit prevents sweating, covering the inside of the tank with foam or rubber. The insulation material keeps the sides of the tank from becoming as cold as before, since the tank no longer has contact with cold water. An owner installs the kit by draining all the water out of the tank. Next, cut pieces of foam or rubber to fit the walls of the tank. An adhesive that comes with the kit contains the pieces on the sides of the tank.

The anti-sweat valves

An alternative to tank insulators, anti-sweat valves introduce some hot water into the water supply of the toilet. This hot water is mixed with cold water, raising the temperature enough to avoid any future ideally odorless sweat. Some anti-sweat valves come with an adjustment option, which allows the user to increase or decrease the amount of hot water entering the water supply of the toilet. These valves also allow the user to close the valve during the cold times of the year.

TOTO C744E#01 Drake Elongated Bowl, Cotton White

How to repair a crack in a toilet tank

Today's plastic toilet cisterns rarely crack, but older porcelain tanks can crack due to damage or impact. It is common to replace a toilet tank when a crack occurs, since crack repair may require more time, effort and cost than a simple replacement. However, small cracks lend themselves to a quick repair job needing only a few materials and tools that can be easily obtained. Give a repair crack to the toilet tank one chance before looking for a new tank.



TOTO C744E#01 Drake Elongated Bowl, Cotton White

Instructions

1 Close the water to the tank and dry the tank completely. Clean the area of ​​the crack.

2 Drill a hole completely through the porcelain with a Dremel tool and little rotary shredder with embedded diamonds. Pierce the farthest visible extension of the crack. Wet the bit periodically with a sponge to keep it cool, which will control dust and keep the crack from spreading.

3 Drill a V or U-shaped area along the crack to remove dirt and give the epoxy a large surface for bonding. Drill the area about 1/8 inch deep and 1/8 inch wide.

4 Fill the crack with industrial white epoxy. Soften the epoxy so that it rises just a little higher than the level of the surface of the toilet tank. Put a piece of clear adhesive tape on top of the epoxy-filled crack to keep the epoxy in place while it dries.

5 Sand the epoxy to the surface of the tank. Start with the coarser grain paper (40 to 60 grit) and gradually move to finer grain (600 grit sandpaper). Continue until the cracked area looks smooth. If air bubbles occur, add more epoxy and re-sand after the epoxy dries.

6 surface spray to repair renovation of the spray finish in the epoxy dries and let it dry, followed by a spray repair of the clear surface shine.

Tips and warnings

•     Wear safety glasses for this project.

Saniflo Saniflo 087 Elongated Toilet Bowl only (1.28 GPF) For SANIFLO Macerator Systems White

How to increase the water level in a toilet bowl

Having the proper amount of water in a toilet bowl helps to flush it completely clean. The amount of water in each individual toilet bowl is determined by the shape of the toilet itself. Some are designed to leave only a small amount of water in the cup. However, if the water level in the toilet is not allowing the passage of fluid each time, it can be easily adjusted with a few simple steps.



Saniflo Saniflo 087 Elongated Toilet Bowl only (1.28 GPF) For SANIFLO Macerator Systems White

Instructions

1 Remove the lid of the toilet tank by simply lifting it up and locating the float inside the tank. The float looks like a ball and is usually attached to the end of a metal or plastic rod.

2 Locate the screw that is on the opposite end of the float, in which the metal or plastic rod is connected to the water valve. If you see more than one screw, adjust the screw that connects to the metal or only plastic rod.

3 Adjust the screw with a screwdriver, to reset the height at which the float closes the water valve. Each bath may be different, but most likely you will have to turn the screw counterclockwise. Adjust the screw approximately 1/4 turn, check the water level and repeat this process until the desired water level is reached.

American Standard 3717B001.020 Cadet 3 FloWise Right Height Round Front Toilet Bowl Only in White

The addition of water to the back of a toilet tank

The back of a toilet consists of a tank that contains the water that is used when flushing the toilet. The water drains from the tank to the bowl when the chain is pulled, pushing the water from the bowl and the contents down the drain. If the water level of the tank is too low or if you need more water to add pressure to push down contents of the cup that are not easily flushing, you can add water to yourself. This is not a permanent solution for a toilet that eliminates incorrectly or is always running.



American Standard 3717B001.020 Cadet 3 FloWise Right Height Round Front Toilet Bowl Only in White

Instructions

1 Remove the top cover of the toilet tank. Consider the water level in the tank.

2 Pull the chain while looking inside the toilet tank. Write down where the water level stops. Observe the inside wall of the toilet tank for a watermark or a fading line.

3 Locate the water overflow tube in the tank - a small tube on the top of the tank that deflects the water when the level is too high.

4 Slowly pour the water into the toilet tank until it reaches the level of water discoloration or until it is about one inch below the opening of the overflow tube.

5 Rinse the bathroom to clean the toilet bowl and inspect the level of water that rises in the tank. Add more water if necessary.

Tips and warnings

•     If the water level is consistently low, this may indicate a problem with the toilet itself. If the arm of the float in the tank is not rising or falling, you may need a replacement. If the water runs constantly, it means that the seal flap locking the hole in the bottom of the tank is loose or misaligned. It can also mean that the float arm is perfectly aligned or broken and must be replaced.
•     Do not overfill the toilet tank as this could cause overflow.
•     Use a plunger to unclog a clogged toilet before using the water tank filling method.

TOTO CST743S#01 Drake Round Bowl and Tank, Cotton White

How to increase the amount of water in a toilet tank

The ability of a toilet to flush is determined successfully by the amount of water contained in the tank. Low-flow toilets adjust the mechanics of the toilet bowl to allow a smaller amount of water to clean the toilet. Low-flow and standard toilets must still maintain a specific amount of water in the tank to work properly. The water level has to sit within 1 inch of the top of the overflow pipe. Adjusting the water level is a simple matter of adjusting the float or the float.



TOTO CST743S#01 Drake Round Bowl and Tank, Cotton White

Instructions

1 Remove the lid on the back of the toilet and identify the type of float used in your tank. A ball float is a round ball that connects to the water filling valve through a long, horizontal tube. A flotation cup is a round cylinder wrapped around the filling valve and connected to the tip of the valve through a vertical bar.

2 Adjust the ball float by firmly holding the rod in two hands and bending the rod up or down as necessary. Increasing the water level requires that the float be bent upwards. Let the water fill the tank after adjusting the float to determine if the level is appropriate. Re-adjust as necessary.

3 Adjust the float cup by tightening the adjustment clip on the side of the cylindrical cup that holds the vertical rod against the float cup. Lift the float up or down as desired to adjust the water level. Let the tank filling to test the level. Re-adjust as necessary.

4 Precisely adjust the water level by turning the adjusting screw located at the top, the center of the filling valve. Turning the screw to the right will increase the water level in small increments. The screw can only be adjusted a certain amount before the float locks in place, so only use the adjusting screw for fine adjustment after adjusting the float.

American Standard 3195A101.021 Champion PRO Right Height Elongated Toilet Bowl, Bone

How to stop a water leak in a toilet tank Using Liquid

If you notice a crack in the toilet tank, you will have to act immediately to make sure it does not overflow and completely ruin the tank. Anything larger than a small crack will need to replace the reservoir, so try to repair the crack only if it is 1/16 inch wide or narrower. You can stop the leak using a liquid silicone sealant to seal the tank.



American Standard 3195A101.021 Champion PRO Right Height Elongated Toilet Bowl, Bone

Instructions

1 Open the water connected to the toilet bowl by turning the small knob behind the toilet cistern to the right.

2 Empty the toilet tank by hitting the discharge lever after turning off the water.

3 absorb all the excess moisture with towels.

4 Blow the inside of the tank completely dry using a hair dryer. If you wish, you can allow the tank to air dry, but this can take hours. Make sure the tank is completely dry before proceeding to the next step.

5 Wear safety glasses and rubber gloves. Apply a test line of epoxy water to silicone pipes over the crack, starting 1/2 of an inch before the crack and ending 1/2 inch beyond it.

6 Slather the epoxy water test silicone pipes without problems on the crack, using a spatula.

7 Allow the water-resistant epoxy silicone plumbing to dry for 24 hours.

8 Close the water to the bathroom again and let the tank refill.

TOTO CST744SL#01 Drake 2-Piece Ada Toilet with Elongated Bowl, Cotton White

How to connect a water supply pipe to a toilet tank

If you connect a new toilet or the installation of a shut-off valve in an old toilet, you will have to connect the water supply line to the toilet cistern. The type of pipe you choose will determine how difficult this job is. While this website recommends a sturdy section of the chrome tube, it can be difficult to bend. If you want to make the job easier, go with a flexible tube section instead.



TOTO CST744SL#01 Drake 2-Piece Ada Toilet with Elongated Bowl, Cotton White

Instructions

1 Close the water flow to the main one.

2 Screw the lock valve nut into place so that it is properly connected to the service.

3 Connect the new tube to the bath by screwing the white plastic nut into place. This will help you see how it aligns with the shut-off valve so you know where to bend it.

4 Bend the tube with the help of a tube bender, unless you have chosen a flexible tube. Align the bent pipe once more with the shut-off valve.

5 Cut the excess pipe with a pipe cutter so that the pipe extends about 1/4 inch into the shut-off valve.

6 Connect the top part to the tank by screwing the plastic nut into place. Insert the bronze bushing into the shut-off valve and tighten the compression nut on the shut-off valve completely, but not excessively, as this could damage the pipe.

7 Turn on the water at the shut-off valve.

American Standard 3701.001.222 Yorkville Elongated Pressure Assisted Two Piece Toilet, Linen

How to move water in the toilet tank

The displacement of water inside a toilet tank is a way to reduce your water consumption. Decreased water consumption is the environment and can also reduce your monthly water bill. According to the Daily Green website, you can save up to 10 liters of water per day by moving a small amount of water into the tank. Displacement means placing an object in the toilet tank. This object is carried to the volume, leaving less space for water.



American Standard 3701.001.222 Yorkville Elongated Pressure Assisted Two Piece Toilet, Linen

Instructions

1 empty a plastic water bottle. Place about an inch of sand in the bottom. You can replace small stones or pebbles from the sand.

2 Fill the water bottle almost to the top with clean water. Close the lid.

3 Lift the lid of the toilet tank. Carefully lower the water bottle to the bottom of the tank on the opposite side of the float arm and the water tube. You can lay it flat if there is enough space, but having to stand up is acceptable. Make sure it does not sit on top of the tank drain cap.

4 Replace the toilet tank lid and pull the chain to empty and refill the tank.

Tips and warnings

•     Periodically open the lid of the tank and the position of the water bottle to prevent it from drifting towards the other side of the tank. If you find that the bottle is moving around and there is a small gap between the opposite corner and the water pipe; Carefully place the bottle between the corner and the tube. Make sure it does not interfere with moving parts.
•     Use a smaller bottle, as a larger one can displace the excess water and prevent proper washing.
•     Do not place other objects in the toilet that can clog moving parts or, like bricks, can disintegrate in the toilet tank.

TOTO CST715#01 Carusoe Round Bowl and Tank, Cotton White

How to adjust the water level in a toilet tank

A toilet that does not have sufficient washing power may need to adjust the water level. Before its exit, the water is carried out in the tank. When the handle is pressed, the discharge valve opens inside the tank, allowing all the water inside to run out. An accessory calls a filling valve then refills the tank. A float connected to the fill valve cuts the water when the water inside the tank is at a predetermined level. Adjusting the water level in a toilet tank can help your toilet achieve its full washing potential.



TOTO CST715#01 Carusoe Round Bowl and Tank, Cotton White

Instructions

1 Remove the lid of the toilet tank. In a double flush toilet, you have to unscrew the flush button to remove the lid.

2 Determine what type of toilet system you have. The two main types of filler levers are of the float type or the integrated float type. The float can be identified as it uses a large rubber or plastic paddle attached to an arm in the tank. The integrated float is a ring-shaped assembly that is placed around the filling valve.

3 Adjust an integrated float assembly by turning the water level adjustment screw located on the top of the fill valve. Turning the screw to the right decreases the float, which lowers the water level, while adjusting the screw to the left increases the level.

4 Adjusting a float ball assembly by bending down the float connection bar to the fill valve. Bending the rod down decreases the level, while bending upwards does the opposite.

5 Pull the chain. Watch as the water level refills, and then adjust as necessary.

Tips and warnings

•     If you have a larger ball float type, you may want to think about switching it out for an integrated valve filler assembly. They are cheap and can save water in the long term.

Kohler K-4306-G9 Kelston Toilet Bowl, Sandbar

Can I Double the Float Path to save water in a toilet tank?

Saving water is always a good thing. Not only reduce your utility bills but it is also good for the environment. You can easily cut off your water consumption by adjusting the water level in your toilet cisterns. Adjust some of the internal components of the toilet tank, such as your float or replace the larger parts.



Kohler K-4306-G9 Kelston Toilet Bowl, Sandbar

Float operation

A retaining nut located at the bottom of the long fill shaft has the float valve in place. A hose that leads back to the water supply valve on the wall or floor provides water for the valve. The float assembly is connected to the upper part of the float valve. When the water reaches a pre-set level, the filling valve automatically switches off.

Water level

The level of water in the tank provides the energy for the discharge into the container below. The more water in the tank, the greater the power of the discharge. A tube in the center of the tank, called the overflow tube, siphons the excess water when a certain level is reached. This prevents the toilet from overflowing if the float malfunctions.

Rod Float Flex

The float rod extends from the top of the float valve filling valve to the float. The float is usually made of plastic or rubber. The float moves on the surface of the water and carries the rod with it. When a set point is reached, the float causes the rod to lift a handle and cut off the water. It is possible to bend the float valve down to save water in a toilet tank, but that could end up damaging the float rod and care must be taken.

The displacement of water

You can also store water in the toilet without bending the float valve float (and possibly breaking it) by using bricks or a quart containers inside the tank. Fill the fourth container with water (either from the sink or the tank) and set it on the bottom of the tank. You can do the same with a standard brick masonry. Any of these operations will raise the water level in the tank, which effectively cuts the float off before, the same as if the rod is bent.

Replacement of float

Installing a new float valve assembly is probably the best and most efficient way to lower the water level in your manufacturers sell generic tank.Many ballcocks that fit in a number of different toilet models. Some of the new float valve assemblies have a float or o-ring type, which is much easier to adjust than bending a rod. These filling valves have also been built in anti-siphon devices, which codes for construction in your area. It may require.