The whole business of making things with raised panels has given me lots of thought over recent years. But router bit sets for making raised panels are relatively expensive, and very limited in terms of thickness of material they can handle.
They also prevent the use of mortise and tenon joints on the frame, because the throat depth on the router bits is too small to accommodate much of a tenon. So I did an experiment to see how well I could shape the frame more by hand. I just made the panel flat (no need for a bit), and used a quarter round router bit as far as I could into the corner, and then carved all the way into the corner with a chisel. So I could approximate the effect of the raised panel router bits this way.
Night Therapy Platform Metal Bed Frame/Foundation Set(SmartBase + Metal Brackets for Headboard & Footboard + Bed Skirt - Queen) - No Box Spring needed
Although it was labor intensive, I was reasonably satisfied with the results. I would not like a whole kitchen this way, but I figured it might be good for a project.
I figured this approach would be nice for a headboard for a bed, and I wanted to build a new bed frame anyway. So I bought the lumber and started working away at it. I decided to go with a non-square shape for the panels. I first cut out the basic shape with a bandsaw, and then put it together with square mortise and tenon joints.
For the panel, I decided to use some very nice 5-ply 5/16 inch birch plywood that came from a discarded shipping crate. My cheap router bit set came with a T slot cutter of the same thickness, but that bit had no guide roller. So I made a fixed guide, and bolted that to the base router - see image above right. That worked surprisingly well.
After I cut the groove into the frame for the panel, I realized that I could not use the roller guide on my quarter round bit, because I had a grove right where the roller guide would press against the wood. Oops! I could have made another wooden guide, like I did with the other bit router. But I had been thinking of the whole bed a bit more of a hand-carved look, so I just carved an approximation of the quarter round profile with a draw knife and a spoke shave.
I used the same approach to carve the outside edge of the headboard, especially because I did not have the right shape of router bit for the profile I wanted.
The next step was to make the posts for the bed. These I glued together out of two pieces of construction lumber to get the right thickness. Two 2x4's would do the trick, but I have found that I can get a lot better quality lumber by buying 2x10x8 pieces. These, by necessity, have to come from larger trees, and tend to be higher quality. The price per unit of lumber is of course more for these, but using construction lumber for furniture is in general remove cheap, so it does not add much to the cost.
For the tops of the posts, I decided on a ball shaped top. I wanted this to be an integral part of the posts, so this required turning the whole posts on my lathe. Now, my lathe is quite big and heavy, but the lathe was not quite long enough to mount the posts for the headboard side of the bed. It is very low tech, it is easy to build an extension for the tail stock of it out of wood.
I left a little bit of wood past the knob, which I cut off afterwards. That way, the hole I had to drill for the dead center to turn in, and the oil I had to put on it to let it run smooth, were cut away.
The next step was to attach the headboard to the posts. Normally, for this type of joint, I would use a mortise and tenon joint. But, I found myself unable to cut the tenons at the ends of the headboard, because I did not have enough ceiling to put the headboard pieces vertically into my tenon jig on the table saw. Strength for this joint was not critical, so I just decided to join it with dowels.
To get the dowel holes aligned precisely, I had the idea of making a drill out of a piece of hardwood, and just drilling through that to get repeatable hole alignment.
This worked well in terms of getting the holes aligned precisely, but with a catch. I could not fit the headboard in my drill press, so I just drilled the holes with a hand drill. I'm usually pretty good at judging right angles, but it's hard to do while also pushing down really hard on a hand drill. For two of the holes, I was about five degrees off in one axis. I compensated for this by tapping on one side of the dowels for those holes, and just pounding it with a rubber mallet when I attached the headboard to the posts. I have since then built to horizontal boring jig to avoid this problem.
This being a "proper" wooden bed, it has bed rails on the sides of the mattress. I'm using these bed rail hooks, so the whole bed can be taken apart easily. I bought these at The Home Depot. The Home Depot calls them "bed rail clips", but you will have more success on the internet searching for "bed rail hooks". Last time I checked, The Home Depot only carried the 4 "bed rail hooks, which would be too small for this bed. through the bed rail so that the screws holding the bed rail clips actually have some cross-grain hardwood to thread in. These are blind holes, so they can only be seen from the mattress side when the bed is assembled - see image at right.
The side rails also have a ledge on the inside to hold the slats (not yet mounted in the picture at right). The slats are essentially supported by the bed rails.
The foot board for the most part is the same as the head board, but shorter, less curved, and without any panels in it.
The bed was too large for me to be able to assemble it in my workshop , so I did not actually assemble it completely until after it was all done and varnished. The first time I put it together was in my driveway. After I took this photo, I shortened the legs a little bit.
The next test assembly was in my living room with the mattress in it. At that point I decided to taper the ends of the slats so they would sit a bit further down in the bed frame. This lowered the mattress down by about a centimeter. And then finally, I set it up in my bedroom.