Material's list
The list of materials below assumes that all wood is good. You should buy extra wood to get rid of the defective parts. It is generally best to buy wider boards and cut them lengthwise into narrower pieces, such as buying 2x6 lumber and cutting the 2x3 pieces from them. You get much better wood that way. It may be better to buy five pieces of 2x10x8 'instead of the parts marked with an asterisk and cut everything from them.
Zinus Arnav Modern Studio 10 Inch Platform 2000 Metal Bed Frame / Mattress Foundation / No Box Spring Needed / Wooden Slat Support / Good Design Award Winner, King
Part Quantity Used for
- 2x8 x 8 ' 3 * Side stringers, also lower horizontal part of the headboard and feet.
- 2x3 x 8 ' 3 * To make poles
- 2x10 x 8 ' one * For the horizontal top part of the headboard and the feet.
- 2x2 x 8 ' two Supports for the slats on the side rails.
- 1x4 x 8 ' 6 For the lamas.
- 3/4 "tarugo 6 ' To cut off the plugs. Buy enough length to get 6 '(feet)
- 2.5 "# 10 wood screw 24 To mount the side rails
- 2.5 "# 10 wood screw 10 To screw the brackets for the slats on the side rails.
- Wood glue 100ml At least 100ml of wood glue.
Cut in section
- Notice how the slats rest on the shelf inside the side rails.
- Mattress 7 "thick.
- Lamas 3.5 "x0.75" x38.5 ", 12 pieces.
- The slats rest on the shelf of the side rails.
- Dimensions of the headboard
- All outer edges have a 1/4 "x1 / 4" bezel. This is best done with a few passes of a carpenter's brush (not the electric one).
- Headboard assembly
- The holes for the plugs are best drilled by fastening the header board and post together with sergeants and drilling the hole completely from the outside, as indicated in the diagram below.
- This part is glued after the rest of the headboard is glued.
- Tarugo 3 / 4x3.5 "
- Hold the post and the board together in position. Then drill through both.
- Do not drill the holes for the screws until you assemble the bed.
Dimensions of the feet
The feet are practically identical to the headboard. If you are one of those people who prefer to hang their feet outside the end of the bed, leave without putting the top horizontal board and make the legs only 18 "high.
Rails of the bed
The side rail has a series of blocks in the inner corner. The purpose of these is to space the slats and prevent them from slipping out of position.
It is better to glue and screw the 1.5 "x1.5" brackets for the slats to the main part of the spar, to make sure it is solidly attached.
- Stringer cut from a 2x8.
- Bevel the edges making several passes with a carpenter's brush.
- Stick wooden blocks with glue, 0.75 "x0.75" x2.5 "
- 2x2 stuck to the side of the crossbar. The 2x2 measures 74 "long
Assembly
Bed structures in general are designed to be dismantled when they move. In this bed structure, unscrewing the side rails allows us this trick.
The slats are placed between the side rails and held in place only by gravity. The blocks on the side stringers prevent them from slipping out of place.
The first and last slats need to cut notches in the corners to fit the posts.
Cut the 1x4 wood slats.
Pre-assemble the structure, then drill the holes for the screws through both parts. That way your holes for the screws will be aligned.
Use 3 "# 10 wood screws.